Verify whether the system of forces shown can be replaced by a single equivalent force. If it can be replaced determine the point where the line of action of the single equivalent force intersects with the xz-plane. Note: If the system cannot be simplified into a single equivalent force system, write CS (Cannot be Simplified) into the answer box. y A 12 kN 30 kN B 18 kN 300 mm 18 kN 30 kN 500 mm 400 mm

Verify whether the system of forces shown can be replaced by a single equivalent force. If it can be replaced determine the point where the line of action of the single equivalent force intersects with the xz-plane. Note: If the system cannot be simplified into a single equivalent force system, write CS (Cannot be Simplified) into the answer box. y A 12 kN 30 kN B 18 kN 300 mm 18 kN 30 kN 500 mm 400 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Replace the loading system by an equivalent resultant force and couple moment acting at point ?. Length AB = 1m Length BC = 2m F1 = 80 N F2 = 60 N F3 = 120 N Angle with respect to x-axis = 32 degrees Moment couple = 195 Nm
Determine the reactions in pounds the hinge and the rocker exert on the beam supporting the distributed load. (Assume that the +x-axis is to the right and the +y-axis is up along the page. Due to the nature of this problem, do not use rounded intermediate values in your calculations or answers) Magnitude and direction Magnitude in lbs. Ax- Magnitude is 0 Ay- By-
The force acting on the gear tooth is 20 N. a. What gives the component of the force along line aa? b. What gives the component of the force along line bb? c. If the component of force F acting along line aa is 30 N, determine the magnitude of force F.
Determine the following unknowns on the beam shown below using Area-Moment Method. Consider 150 mm x150 mm section and E = 80 GPa. Show complete and organized solution. a. Vertical Reaction at B in kN. b.Moment Reaction at A in kN-m. c. Deflection at point C in mm. d. Deflection at midspan of AB in mm. Given: a- 7m b- 24kN/m C- 30kN
Statics and Equilibrium Draw a FREE BODY DIAGRAM of Point B. Determine the tension in both Cables AB and BC Use Equations of Equilibrium to solve: ΣFx=0 & ΣFy=0 Please show a different answer other than T1=4.2836kN and T2=16.2992kN
A force of F = {6i - 2j + 1k} kN produces amoment of MO = {4i + 5j - 14k} kN ⋅ m about the origin,point O. If the force acts at a point having an x coordinateof x = 1 m, determine the y and z coordinates. Note: Thefigure shows F and MO in an arbitrary position.
Express the moment of the couple acting on the pipe in Cartesian vector form. What is the magnitude of the couple moment? Take F = 125 N.
Replace the force and torque systemacting on the rectangular block by a key.Specify the magnitude of the force and the moment oftorque of the wrench, as well as the point where its line of actionintersects the x-y plane.
A tapered cantilever beam AB supports a concentratedload P at the free end (see figure). The crosssections of the beam are rectangular with constantwidth b, depth dA at support A, and depth dB = 3dA/2 at the support. Thus, the depth d and moment of inertiaI at distance x from the free end are, respectively, d = (dA/2L)(2L+x) I=(bd3/12) =(bd3A/96L3)(2L+x)3 = (IA/8L3)(2L+x)3in which IA is the moment of inertia at end A of thebeam.Determine the equation of the deflection curveand the deflection δA at the free end of the beam dueto the load P.
Solve the problem completely and neatly. Use 3 decimal places in all your computations except for strain and rho(5 decimal places). Design the number of 36 mm diameter bars to support the maximum positive moment of Mu=1600 kN.m. Use f'c=28MPa, fy=345MPa, h=800mm, bf=1000mm, bw=400mm, flange thickness=100mm, stirrups=10mm, and cc=40mm. Calculate the effective depth of the section in mm.0 Calculate the depth of compression block due to the maximum positive moment in mm.0
Solve the problem completely and neatly. Use 3 decimal places in all your computations except for strain and rho(5 decimal places). Design the number of 36 mm diameter bars to support the maximum positive moment of Mu=1600 kN.m. Use f'c=28MPa, fy=345MPa, h=800mm, bf=1000mm, bw=400mm, flange thickness=100mm, stirrups=10mm, and cc=40mm. Calculate the effective depth of the final section in mm.0 Calculate the depth of the compression block of the final section in mm.0 Calculate the depth of the neutral axis of the final section in mm.0 Calculate the ultimate moment capacity of the final section in kN.m.0
The bent bar shown is subjected to 3 forces shown. Replace these forces with an equivalent couple M and single force F at point A. Show solution to answers M = 21.8 kN-m, cw Fv = 12.03 kN, D FH = 1.60 kN, R