ViRiVoIlThe elements in the circuit shown have the following values: R = 2570.11 N. R2 = 4277.34N. R3 = 4236.39 N. R4 = 622.17 N. Vị = 102.816373 V. h = 0.0176 A.Determine the following: a.) Using any circuit method you prefer, solve for the voltage V, b.)Determine the current flowing through R4. c.) Determine the magnitude of the currentflowing through the resistor R3 (Hint: Assume the current flows up through R3). d.)Determine the power dissipated by R4 (in Watts).

Answered: Vi Re hy Vo Il +

Engineering

Electrical Engineering

Vi Re hy Vo Il +

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

following equation applies: V = IR. Outside of the linear range, V*IR, outside of the linear ranges where resistors are broken The resistor has a resistance of 100ohm, and a power rating of 250mW. 1) Sketch the plot (and label) of the i-v relationship for the resistor using only the linear range of the resistor. Determine the range of values for the voltage and current that the resistor operates as a linear element and note these simplified numerical values on the plot.
1. In a circuit that contains only resistors in series, the current is the same throughout the circuit (remember that current is conserved!). The amount of current in the circuit is determined by the potential difference (or em f) of the battery and the equivalent resistance, Req, of the circuit. We can therefore write Ohm's Law as DeltaV = IReq. Assume the batteries supply a potential difference of DeltaV = 3.0 V, and use the currents measured in circuits 3a, 3b, and 3c to determine the equivalent resistance in each circuit. Please show the calculation of each. R1 = 150 ohm, R2 = 230 ohm R3 = 270 ohms (don't believe question should need these but providing anyways) Current MeasuredCurrent through R1 in 3a (Only resistor 1) Ir1= 0.01 amp Current through R1 in 3b (Resistor 1 and 2) Ir1= 0.0032 amp Current through R1 in 3c (Resistor 1, 2 and 3) Ir1 = 0.002 amp
Using Kirchoff's voltage law to determine the unknown voltage E2 for the configuration given in the figure below. Given that: - The source E1= 110 VV, - V1= 23.5 V, V2= 18 V, V3= 16.4 V, and V4= 20.5 V
Since R1=9282.13ohm, R2=3403.87ohm and Ri=Infinite in the circuit given in the figure, write the equivalent resistance in Ohms between the terminals A-B.
A solar cell with a reverse saturation current of 5 nA is illuminated such that the short-circuit current is Isc = 200 mA.a. Plot I-V and obtain the voltage at maximum delivered power.b. Assume that this cell has a series resistance of 1 Ohm, so that the cell voltage is reduced by the IR drop. Replot the I-V curve for this case and compare with the plot in a.
Given the circuit below and that R1=1.7ohm,R2=3.5ohm,Emf1=2.1V and Emf2=6.3V. What is the current through the section ac?
Look at the images shown. Why can we measure resistance with a pencil drawn on a piece of paper? What is the component/material that is on the pencil that gives a high resistance? With the values given on the images, what are the corresponding color codes (indicate tolerance using a 4-band color code scheme)? If the first value is connected in series with the other value, what is the total resistance? If it’s parallel what is the total resistance? 0.449 mega ohms 102.2 kilo ohms
Given:Vb = 100 voltsR = 10000 ohmsC = 200 μFAssuming that after a long period of time, the switch is flipped from position "A" to position "B" at t=0. Determine the current in the source-free circuit after 1 second.
In the circuit shown in the figure, the values of the circuit elements are given below.Accordingly, what is the voltage across the resistor R3 at t=0.4 seconds?R1 = 10 ohmsR2 = 8 ohmsR3 = 5 ohmsL = 8 hensC = 1/2 faradV = 14 u(t) VI = 8/5 u(t) A
can someone show me step by step how to do this problem and explain the concepts A device, shown in Figure P3.5a, can be modeled by a current source in parallel with a resistance. The relationship between the current through the device, iX, and the voltage across the device, vX, is given in the plot in Figure P3.5b. a) Find a model for the device that would be valid when current is in the range 1[mA] < iX < 5[mA]. This model must have numerical values for the current and resistance, and the polarities with respect to vX and iX should be shown in a diagram. b) A voltage source is applied across the device so that vX = 10[V]. Find the power delivered by the device in this situation.
Vbatt=25 VC1=90 ?CC2=75 ?CC3=60 ?CR1=160 ΩR2=120 Ωt2=21.6 msect3=27 msecConsider the circuit shown below which shows a battery connected to some resistors and capacitors along with some switches which will be toggled opened or closed at different times. The components are listed above. The capacitances are in microCoulombs (?C), the resitances are in Ohms (Ω), and the times are in milliseconds (msec). A stopwatch is started at time t1=0 ms. At that time, switch S1 is closed and all other switches are open and the capacitor is allowed to charge up.(a). What is the charge (in uC) on C1 at the time the stopwatch reads t2=21.6 ms?Ans: 1750 uC(b). What is the current (in mA) through R1 at t2=21.6 ms?Ans: 34.9 mA(c). What is the voltage (in V) across R1 at t2=21.6 ms?Ans: 5.58 V(d). What is the voltage (in V) across C1 at t2=21.6 ms?Ans: 19.4 V(e). What is the energy (in mJ) in C1 at t2=21.6 ms?Ans: 17.0 mJThen, immediately at time t2=21.6 on the stopwatch, switch S1 is thrown open and…
Using Kirchoff's voltage law to determine the unknown voltage V3 for the configuration given in the figure below. Given that: - The source E= 90 V, - V1= 10 VV and V2= 10.3 VV.