View Policies Current Attempt in Progress The steel pipe column shown has an outside diameter of 7.675 in. and a wall thickness of 0.25 in. The timber beam is 10.75-in.-wide, and the upper plate has the same width. The load imposed on the column by the timber beam is 98 kips. Determine the average bearing stress at the surfaces between the pipe column and the upper and lower steel bearing plates. 10,75 in. Timber beam Upper bearing plate Steel pipe Lower bearing plate Concrete slab a a O 15.69 ksi O 22.87 ksi O 11.89 ksi O 16.81 ksi O 19.75 ksi

View Policies Current Attempt in Progress The steel pipe column shown has an outside diameter of 7.675 in. and a wall thickness of 0.25 in. The timber beam is 10.75-in.-wide, and the upper plate has the same width. The load imposed on the column by the timber beam is 98 kips. Determine the average bearing stress at the surfaces between the pipe column and the upper and lower steel bearing plates. 10,75 in. Timber beam Upper bearing plate Steel pipe Lower bearing plate Concrete slab a a O 15.69 ksi O 22.87 ksi O 11.89 ksi O 16.81 ksi O 19.75 ksi

Principles of Foundation Engineering (MindTap Course List)

9th Edition

ISBN:9781337705028

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter16: Lateral Earth Pressure

Section: Chapter Questions

Problem 16.15P

See similar textbooks

Similar questions

a 300 mm thick footing slab supports a 300 mm thick concrete wall carrying uniform service dead load of 214.31 kN/m and service live load of 145.94 kN/m. the base of the wall footing slab is 1.2 m from the ground surface. design parameters are as follows: ysoil = 16 kN/m^3, yconci = 24 kN/m^3. qa = 215.46 kPa. f'c = 27 MPa and fy = 420 MPa. 1. calculate the required center to center spacing of 16 mm bars for flexure if the maximum factored moment in the slab is 75 kN.m a. 150 mm b. 180 mm c. 210 mm d. NOTA 52. calculate the ultimate beam shear stress on the footing slab if the footing slab is 2.1 m wide. a. 1.25 MPa b. 0.74 MPa c. 0.87 MPa d. 0.96 MPa
The billboard shown is supported by structural tube that has a 380 mm outer diameter and 38 mm wall thickness. If the billboard is under wind pressure Pwind and has weigth of Wbillboard, determine the principal stresses and max. in-plane shearing stress at point H. Assume wind is applying uniform pressure all over the billboard and centroid of the billboard is located at point C. You can ignore the thickness of the billboard. P???? =2.3kPa W????????? =80 kN
Pls answer ASAP. Show fbd and diagrams. A sector-shaped sluice gate having a radius of curvature of 18 ft is as shown. The center of curvature C is 3 ft vertically below the lower edge A of the gate about which the gate is constructed to turn. If the water level is 7.9 ft above the lower edge of the gate. (a)determine the magnitude (in kips) and direction (R or L) of the horizontal component of the force acting onthecurved gate AB. (b)determine the magnitude (in kips) and direction (U or D) of the total vertical component of the force acting on the curved gate. (c)determinethe magnitude of the total force (in kips) acting on the gate. (d)determine the angle that the total force acting on the gate makes with the horizontal
A five-storey building is subjected to a windload, computed Vu = 2,350 KN, design the reinforcement of a shear wall that is 5.8m long and 4.2m high, and 250mm thick. F’c= 23.5MPa and fy=275MPa. If the wall is considered to be a load bearing with a concentrated load, Pu= 7,255 KN, can the thickness of wall carry the ultimate axial load, otherwise what is the design wall thickness? Assume . Sketch the rebar details.
The post is fixed to the ground and a rectangular pressure of 7 lb/ ft2 acts perpendicular to the face of the signboard. What resultant internal loadings act on the cross-section through point B of the signpost?
Design the base of the following concrete curtain section, calculating the Safety Factor against overturning. Assume linear distribution of pressure in the subsoil. Free body diagram with the acting forces, calculation procedure, Definition of Width A of the base of the curtain clearly indicated.
The appied load on a shallow square fondation makes an angle of 20° wiht the vertical. Given: B= 5 ft, Df= 3 ft, γ= 115 lb/ft3, φ’= 25°, and c’= 600 lb/ft2. Use FS= 3 and determine the gross inclined allowable load. Use Eq (6.28)
Given a proposed six-story (12 meters by 18 meters) City Library which is to be constructed in the Province of Benguet (site to fault distance of 7.1 km from a fault line-assume seismic source type B). It is designed under reinforced concrete with special moment-resisting frames. Assume an average regular weight per floor area to be 10.5 KPa while the roof deck weighs 8 KPa per floor area. The regular floor-to-floor height is 3.20 m. a. Design Base Shear b. Vertical storey forces in each level. c. Shear force per floor level and the overturning moment per floor level
A 48” O.D., 3/4” steel wall pipeline is buried under the bottom of a harbor. It is proposed that the minimum cover for the pipe under the bottom is 2'. The saturated unit weight of the soil is 110 pcf. Compute the net force on the pipe. Will it float to the surface without the shear resistance of the soil?
A 6 storey with roof deck building has a total height of 21m. The computed base shear is 900 kN. Each floor has an average height of 3.5m. Each floor has a weight of 3500 kN except for the top most level with a weight of 2500 kN. Its natural period of oscillation is 0.75 sec. What is the shear at the 2nd level, 3rd level, 4th level and 5th level?
Rectangular load C to D = 200lb/ft
The dimensions of a 9-m-high warehouse areshown in Figure P2.12. The windward and leeward windpressure profiles in the long direction of the warehouseare also shown. Establish the wind forces based on thefollowing information: basic wind speed = 40 m/s, windexposure category = C, Kd = 0.85, Kzt = 1.0, G = 0.85,and Cp = 0.8 for windward wall and −0.2 for leewardwall. Use the Kz values listed in Table 2.4. What is thetotal wind force acting in the long direction of thewarehouse?