VTH = -0.5V, k = 2mA/V² and λ = 0.05, what is the small signal transconductance (gm) of this MOS transistor in us (no decimal place)? What is its output impedance in kOhms (with 2 decimal places)? (Hint: Use the current equation considering channel length modulation and consider the polarity of the current equation for PMOS transistors) 'Go SS D

VTH = -0.5V, k = 2mA/V² and λ = 0.05, what is the small signal transconductance (gm) of this MOS transistor in us (no decimal place)? What is its output impedance in kOhms (with 2 decimal places)? (Hint: Use the current equation considering channel length modulation and consider the polarity of the current equation for PMOS transistors) 'Go SS D

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

What are the advantages and disadvantages of single-sideband transmission? Briefly describe each.
[Q1] A carrier signal (peak amplitude = 39V, frequency = 100MHz) is frequency modulated by the baseband signal (peak amplitude = 5V, bandwidth = 12.02kHz). The frequency deviation is 77.53kHz, and the load is 510. Determine (a) the load power, (b) the bandwidth of nsmitted signal. (consider only VnG)|> 0.1).
2. The output stage of a transmitter requires, owing to supply voltage limitations, a downward impedance transformation of the antenna resistance. The load impedance is 50-Ω. Suppose we wish to deliver 3 Watts of power into such a load at 915 MHz, but the power amplifier has a maximum peak-to-peak sinusoidal voltage of only 7 Volts because of various losses and transistor breakdown problems. Design a two section L-match of low pass type to allow that 3 Watts to be delivered to the 50-Ω load. Assume that all reactive elements are ideal.
Answer the question: For a QPSK modulator with an input data rate (fb) equal to 10 Mbps and a carrier frequency of 70 MHz, determine the minimum double-sided Nyquist bandwidth (fN) , the highest fundamental signal, and the baud rate.
pls list the step by handwritinga) Sketch the spectrum of g(t)?b) Sketch the spectrum at point (a) of the conversion system?c) What should the parameter w0 be relative to wc?d) What should be the value of passband gain A?
For an FM modulator with a modulation index mf = 1, a modulating signalVm(t) = Vm sin(2π1000t) and unmodulated carrier Vc(t) = 10 sin(2π500kt),determinea) Number of sets of significant sidebandb) Their amplitudec) Then draw the frequency spectrum showing their relative amplitudesd) Determine the unmodulated carrier power for the FM modulator(assume a load resistance RL = 50 Ω)e) Determine the power in the modulated carrier and each side frequency,and sketch the power spectrum for the modulated wave.
An analog signal is given as?(?) = 5 + 2 cos(20??) + 3 cos(400??)a) What is the bandwidth of ?(?)? Determine the Nyquist sampling frequency for ?(?), both in radian/sec (?? ), and in Hz (?? ).b) Formulate ?? (??), the signal sampled with the Nyquist frequency.c) Plot frequency spectrum of the sampled signal, ?? (??).d) Determine the filter to reconstruct the signal ?(?).e) Is it possible to reconstruct the signal ?(?) for ?? = 0.004 [s]? State that if aliasing error occurs or not.
-MCQ- FM modulator is used to transmit a cosine message signal with 4V amplitude and 20Hz frequency. The frequency deviation constant kf = 25 Hz/V, the carrier is a cosine sign with an amplitude of 10V and a frequency of 2000Hz. The FM modulated signal is passed through a bandpass filter and 90% of the power of the modulated signal remains. What is the bandwidth of the FM modulated signal in this case? a) 240hz b) 20hz c) 100hz d)200hz
1.Select the correct statement(s) regarding frequency modulation (FM) bandwidth. a. the more the carrier frequency is allowed to change frequencies (Δf), the smaller the modulated signal bandwidth b. the larger the FM index, β, the larger the modulated signal bandwidth c. as you increase kvco, you decrease modulated signal bandwidth d. all statements are correct 2. Select the correct statement(s) regarding baseband signal modulation. a. with modulation, a baseband signal can be moved to a higher frequency thus preventing baseband signal interference b. modulation techniques are only required for analog information signals, since digital signals are represented by discrete logical values of “1” and “0” c. modulation eliminates the baseband signal’s frequency bandwidth, thus enabling greater efficiencies when transmitting a modulated carrier signal d. all statements are correct 3. A…
a) Sketch the spectrum of g(t)?b) Sketch the spectrum at point (a) of the conversion system?c) What should the parameter w0 be relative to wc?d) What should be the value of passband gain A?
A. The baseband signal in the image Is transmuted by using a linear delta modulation (ΔM), the modulator has the following specifications Sampling rate = 5 Fnyquist, where Fnyquist is the Nyquist rate of the baseband signal, bandwidth = 5 KHz. 1. Determine the maximum step size Δ for delta modulation of this signal, which required avoiding slope overload. 2. Determine the signal to noise ratio in decibel for the signal. 3. What is the maximum power that be transmitted without slope overload distortion 4. if the step size of the delta modulation is 0.02 determine the amplitude and maximum power of baseband signal to a void slope overload .
How many channels are available in the 2.4 GHz band? List all the channels. What is the channelbandwidth?