Water flows through a tube of 5mm inside diameter with a volumetric flow rate of 7.8 cm3/s. Wall temperature of the tube is kept constant at 80oC. In a fully developed velocity and temperature profile region of 5m length, calculate the bulk temperature of exiting water if its inlet temperature is 20oC

Water flows through a tube of 5mm inside diameter with a volumetric flow rate of 7.8 cm3/s. Wall temperature of the tube is kept constant at 80oC. In a fully developed velocity and temperature profile region of 5m length, calculate the bulk temperature of exiting water if its inlet temperature is 20oC

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter7: Forced Convection Inside Tubes And Ducts

Section: Chapter Questions

Problem 7.20P

See similar textbooks

Similar questions

6.1 Determine the heat transfer coefficient at the stagnation point and the average value of the heat transfer coefficient for a single 5-cm-OD, 60-cm-long tube in cross-flow. The temperature of the tube surface is , the velocity of the fluid flowing perpendicular to the tube axis is 6 m/s, and the temperature of the fluid is . Consider the following fluids: (a) air, (b) hydrogen, and (c) water.
Air (1 atm) enters into a 5-cm-diameter circular tube at 20°C with an average velocity of 5 m/s. The tube wall is maintained at a constant surface temperature of 160°C, and the outlet mean temperature is 80°C. Estimate the length of the tube.
Cold air at 5°C enters a l2-cm-diameter, 20-m-long isothermal pipe at a velocity of 2.5 m/s and leaves at 19°C. Estimate the surface temperature of the pipe.
Fluid flows at an ambient temperature of 87 oC at a speed of 0.4 m/s through a smooth pipe with a diameter of 20 mm, a length of 24 m and placed horizontally, and heats a medium. Considering that the pipe surface temperature remains constant, inside the pipe; a) In case of water flow,b) In case of engine oil leakage Calculate the heat transfer coefficient and the friction factor in the in-pipe flow and compare and interpret the results.
Water at 15°C is to be heated to 65°C by passing it over a bundle of 4-m-long, 1-cm-diameter resistance heater rods maintained at 90°C. Water approaches the heater rod bundle in normal direction at a mean velocity of 0.8 m/s. The rods are arranged in-line with longitudinal and transverse pitches of SL=4 cm and ST=3 cm. Determine the number of tube rows NL in the flow direction needed to achieve the indicated temperature rise. Please, I need the solution from fundamental concepts of how the heat flow behaves in the system. That it be answered with theory of the subject
Water at 15ºC is to be heated to 65ºC by passing it over a bundle of 4-m-long 1-cm-diameter resistance heater rods maintained at 90ºC. Water approaches the heater rod bundle in normal direction at a mean velocity of 0.8 m/s. The rods arc arranged in-line with longitudinal and transverse pitches of SL 4 cm and ST 3 cm. Determine the number of tube rows NL in the flow direction needed to achieve the indicated temperature rise.
Example 4: Hot air at atmospheric pressure and 80°C enters an 8–m-long uninsulated square duct of cross section 0.2 m  0.2 m that passes through the attic of a house at a rate of 0.15 m3/s (Figure). The duct is observed to be nearly isothermal at 60°C. Determine the exit temperature of the air and the rate of heat loss from the duct to the attic space.
Water with a mass flow rate of 0.002 kg/s at 18oC flows inside a tube while the flow is already developed hydrodynamically. The inner diameter of the tube is 1.5 cm, and the inner pipe wall temperature is maintained uniformly at 125oC. Calculate the required tube length to increase the water temperature to 82oC.
Water at 10oC enters a tube of 0.1 m diameter at the mean flow velocity of 0.4 kg/s. Calculate the exit water temperature if the tube is 15 m long and the wall temperature is constant 30oC.
Engine oil at 60ºC (μ = 0.07399 kg/m s, ρ = 864 kg/m3) flows in a 8-cm-diameter tube with a velocity of 2.2 m/s. Determine (a) the friction factor and (b) pressure drop along a fully developed 6-m long section of the tube Water at a mean temperature of 25°C flows across a 1-cm square tube in cross-flow with a Reynolds number of 10,000. Calculate (a) Nu and (b) the convection heat transfer coefficient.
1) Atmospheric air at 25oC and with a speed of 50 m/s is pumped by a fan over a flat plate. a)What is the minimum plate length in order to achieve a Reynolds number of 108 ? b)At what distance from the leading edge would transition occur if critical Re #= 5x105 ? 2) Local Nusselt number is given as Nux=0.04Rex0.9 Pr 1/3. Obtain an expression for, a) average heat transfer coefficient, x b) local heat transfer coefficient, hx c) What is the ratio of the average to local coefficient, x / hx 3) Air is in parallel flow over a flat heater surface which is to be maintained at 140oC. Airflow induces a drag force of 0.25 N on the heater. What is the electrical power needed to maintain the prescribed surface temperature? 4) Air at 1 atm with a velocity of 4 m/s and a temperature of 50oC flows over a flat plate that is at a uniform temperature of 100oC. The plate has a length of 0.20 m and a width of 0.1 m. a) What is the average heat…
The fluid flows at a speed of 0.4 m/s through a horizontally placed smooth pipe with a diameter of 20 mm and a length of 24 m and heats an environment at a temperature of 87 oC. Considering that the pipe surface temperature remains constant, inside the pipe; a) In case of water flow,b) In case of engine oil leakage Calculate the heat transfer coefficient and friction factor in the in-pipe flow and compare and interpret the results.