Water flows through the curved pipe shown in the figure below where point X denotes the center of gravity of the system. Considering the weight of the pipe and water with-in as WG which acts at a distance of X m from pipe axis, answer the following questions: 1) What are the horizontal and vertical components of the force provided by the flange at point A? 2) What is the moment provided by the flange at point A? D2 Patm H D1 A L

Water flows through the curved pipe shown in the figure below where point X denotes the center of gravity of the system. Considering the weight of the pipe and water with-in as WG which acts at a distance of X m from pipe axis, answer the following questions: 1) What are the horizontal and vertical components of the force provided by the flange at point A? 2) What is the moment provided by the flange at point A? D2 Patm H D1 A L

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The bar system given in the figure above, (between AB: 1m / BC between: 3m / CD: 2m)a) Show the support reactions and load resultant on the rod?b) find the support reactions?c) find the Normal Force, Shear Force and Moment values by cutting from the points you have determined?d) Draw the cross section effect diagrams? Indicate the maximum positive and negative moment values?e) Check the cross-section influence diagrams with a simple method, explain the control steps briefly?
Very urgent. The box in the figure is connected by a cable from point A to point B. If the stress T in the cable is 5kN, calculate the Moment Mo of this force to point C. A(0,0,5m), B(2m,5m,0), C(4m,0,0)
The rectangular gate has dimensions: h=.8m; b=2.4m;c=0.4m;weighs 2 tons. It slides on a plane of inclination θ=70° and serves to plug the conduit of a dam. Considering that the coefficient of friction is 0.35. Determine the magnitude of the tension T needed to move the gate when the water level reaches the elevation of 62 m.
Water is stored in a tank with an inclined panel AB whose dimensions are 5 ft long by 6 ft wide. The manometer indicates a gage liquid height of z = 2 feet. Determine the pressure (in psf) at B. Determine the pressure (in psf) at A? Apply the pressure prism concept in determining the force (in lbs) exerted on side AB.
The gate AB is a quarter circle of 2.5 meters in diameters and 3 meters wide asshown in figure#2. How Find the horizontal component of the resultant hydrostatic forceacting on the gate in kilonewtons. How find the vertical component of the resultant hydrostatic force actingon the gate in kilonewtons, and how to find the location of PH and Pv from hinge A in meters. And if the weight of the gate is 100 Newtons, how find the force “F” just sufficient to preventrotation about hinge A.
7.) The section of a gate at the end of a tank is shown below. The length of the gate is 3 m normal to the paper and hinge at O. If the depth of water is 2.50 m, neglecting the weight of the gate calculate the horizontal force P to maintain equilibrium. Use unit weight of water 9.80 kN/m^3. Note: change 6 meters arc
Using the Force Method of Analysis, draw the influence line for shear at point C of the beam shown. Plot numerical values every 5 ft. Assume the support at point B is a roller. EI is constant. Express your answers in 4 decimal places.
The sector gate UE is submerged in water as shown in the figure. The sector gate is one-twelfth pf a circle of radius 4.98m. It has a length of 10.4m. Determine the horizontal components (kN) of the resultant force acting on gate.
6.) The section of a gate at the end of a tank is shown below. The length of the gate is 3 m normal to the paper and hinge at O. If the depth of water is 2.50 m, neglecting the weight of the gate calculate the distance of the line of action of vertical component of the hydrostatic force on the submerged curved section of the gate from the y-axis. Use unit weight of water 9.80 kN/m^3. fluid mechanics
A 3-cm-diameter horizontal pipe attached to a surface makes a 90° turn to a vertical upward direction before the water is discharged at a velocity of 6 m/s. The horizontal section is 5 m long and the vertical section is 4 m long. Neglecting the mass of the pipe and considering the weight of the water contained in the pipe, the bending moment acting on the base of the pipe on the wall is (a) 11.9 N·m (b) 46.7 N·m (c) 127 N·m (d) 104 N·m (e) 74.8 N·m
The three forces act on the pipe assembly. If F1 = 80N and F2= 50 N replace this force system by an equivalent resultant force and couple moment acting at O. Express the results in Cartesian vector form.
Collars A and B are connected by a 525 mm wire and can slide freely, without friction, on the rods. If the force P = 370j [N] is applied to collar A and the system is in balance, calculate the intensity of the forces.