Water in the triangular trough is at a depth of y = 3 ft. The drain is opened at the bottom, and water flows out at a rate of V = (7.32 y'/2) ft/s, where y is in feet. The trough has a width of 2 ft. The slit at the bottom has a cross-sectional area of 26 in? . (Figure 1) Part A Determine the time needed for the water to reach a depth of y = 2 ft. Express your answer to three significant figures and include the appropriate units. Value Units Submit Previous Answers Request Answer

Water in the triangular trough is at a depth of y = 3 ft. The drain is opened at the bottom, and water flows out at a rate of V = (7.32 y'/2) ft/s, where y is in feet. The trough has a width of 2 ft. The slit at the bottom has a cross-sectional area of 26 in? . (Figure 1) Part A Determine the time needed for the water to reach a depth of y = 2 ft. Express your answer to three significant figures and include the appropriate units. Value Units Submit Previous Answers Request Answer

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A pipe line between points A and B consist of 305m of 200mm, followed by 245m of 300mm, followed in turn by 150m of 200mm. If n = 0.011 and the total headloss from A to B 3.65m. determine Q by computing the equivalent length of 12in pipe.
Q4: Assuming f-0.020, determine the discharge in the pipes. Neglect minor losses. Pipe Diameter AB 250 mm 200 mm 400 mm BC BD Length 1200 m 600 m 200 m EL.45m EL 3m. B C EL. 3.0m D EL 0.0m
EX(2): Calculate the Diameter for pipe by Chart Method, Given : head losses 50 kpa , L-1250m, Q=126 m3/hr , C= 80 . %3D
A/ Estimate Q in. B/ In the pipe systems show, find the distribution of flow, with a friction factor of 0.0165. Assume that minor losses can be neglected. (Use Darcy-Wiesbach)-Only 3 trail 3169 8 Litmin. 1500m D-0.675m 1200m D-0 675m 2250 Limin. D=0,6m 968.436m D=0.6m 4500 Limin 953.064m 2250 L/min.
3. Determine the Velocity and discharge through the 150mm diameter pipe shown a) assuming no head loss and b) considering a head loss of 200mm El. 30 El. 28 m El. 27.5 m 150 mm El. 24.9 m
Determine the equivalent length pipe with a diameter of 300mm and a C value of 120 that will replace the arrangement from B to D below. A B 1000m, 4000, C=100 600m, 2000, C=85 E 1600m, 3000, C=120 D
1. Calculate the discharge through a 90 mm o sharped edge orifice. Assume Cd = 0.65.
The tank has a square base and is filled with water to the depth of y 0.4 m. If the 20-mm-diameter drain pipe is opened, determine the initial volumetric flow of the water and the volumetric flow when y = 0.2 m. %3D %3D 2 m
5. Water is flowing with flow rate 50 liter/s in a sudden enlargement pipe. The diameter of the larger and the smaller pipe are 200 mm and 150 mm respectively. Determine the head loss through the enlargement. (Ans.: 81.6 mm)
In the branched pipe system below, water is flowing at 0.0142 m3/sin a new, clean DN 100 Schedule 40 pipe (ID = 0.1023 m) at A. The flow splits into two new, clean DN 50 Schedule 40 pipes (ID = 0.0525 m; A = 0.00216 m2) as shown and then rejoins at B. Call the 30 m branch“a” and the other branch “b.” The friction factor in Branch ais 0.021, and the friction factor in Branch bis 0.0215.(Note that if friction factors weren’t given, you’d need to make initial guesses and iterate!)Calculate the flow rate in each of the branches. Include the effect of all minor losses in Branch bbut ignore the tee junctions. The total length of the pipe inBranch bis 60 m. The elbows are standard.(Remember to check that your final answers follow continuity!)
A wooden flume (n=0.012) of rectangular cross section is 2 ft wide. The flume carries 3 ft3/sec of water on a 1% slope. A) What is the depth?B) What is the critical DepthC) What is the EminD) What is the Froud (Fr) Number ot the flow.
: For the following circular channel section (sewer pipe): OF D. Part1 : Compute the maximum flow rate (Qma) the pipe can discharge? - Select the diameter (D) between: 0.51m