we added the shown Pl controler to reduce the steady-state.error of this system to become e 0.1 for a unit step Input Determine Kthat allows us to do that Hint start by finding the static position constant Kp. R6) s(s +4) s +3s-+2s+3 plant K, 2+ Pl controller Select one: O a.9.75 b.6.75 O d. 13.5

we added the shown Pl controler to reduce the steady-state.error of this system to become e 0.1 for a unit step Input Determine Kthat allows us to do that Hint start by finding the static position constant Kp. R6) s(s +4) s +3s-+2s+3 plant K, 2+ Pl controller Select one: O a.9.75 b.6.75 O d. 13.5

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.59P

See similar textbooks

Related questions

Q: Q₂- For the system of open-loop transfer function _4 (5² +10,5+100) 5² (5+3) (5¹+65+10) Find : a-…

Q: 14. Compute the minimal value of K so that the steady-state error due to a unit step distur- bance…

Q: Response Analysis: The system has a unit step input, Find GI A Transfer funstion h What is the…

A: The solution is given below

Q: * for the System in fiqure, find the Coefficients such that the steady-shate error Ki and Kz is 5%…

A: In the control system, Find the value of k1 and k2 for the steady state error 5% If the input is…

Q: For the circuit shown, find the voltage "v" using classical method for t20 when the circuit is in…

A: at t = 0-, inductor act as a short circuit at the steady state IL(0-) = 84+8I=812×9=6 Amp you…

Q: A first – order system and its - response to unit step input as in Figure, what is the correct…

A: Last option is correct. The detailed solution is provided below.

Q: 2: For the pole-zero plot shown in figure Q2, answer the following a- Find the time response (y(t))…

Q: Suppose the proportial gain K is tuned so that the minimum requirement for the steady state error of…

A: 11.(b) The steady state of a system is dependent on the proportional constant which is K here input…

Q: Q2: If the discrete time signal f(n) = 28(n+2) - 28(n+1) + 28(n) - 28(n-1) + 28(n-2), sketch. -2x(n)…

A: The signal x (n) can be drawn as:

Q: 9o improve the transient behavior of and SCS+2) anity Reed back Lind all time domain the system…

A: (1) We are given a system having open loop transfer function shown below: Gs=25ss+2 We have to find…

Q: splane ** * * ja s-plane d

Q: 0.8e jn/4 0.8e ja/4 hi(n) h2(n)

A: as per our company guidelines we are supposed to answer ?️only first 3️⃣ sub-parts. Kindly repost…

Q: Perform a 200-case Monte Carlo analysis of the DAC and find the worst-case differential and integral…

Q: Discuss the concept of unit-step, impulse and sinusoidal response and provide at least one…

Q: Q1 (a) The characteristic equation of a general nth order system is given by q(s) = s" + a,s"-1 +…

A: Given : Note: It is the kind notice that according to the guidelines of the company we supposed…

Q: Ex. 862 298. A closed-loop system has poles shown as x's in the complex plane. For a closed loop…

Q: 64 G(s) s2 + 2s + 64

A: We know direct formula for rise time settling time and overshoot for given system .

Q: Consider the 2nd order system as shown in the figure. Find the Problem (1] output response ot the…

Q: Q1 (а) The characteristic equation of a general nth order system is given by q(s) = s" + a,s"-1 +…

A: NOTE: Since you have asked multiple question, we will solve the first question for you. If you want…

Q: For the circuit shown below, let Va - 3.8V Vy-0.7V and vị = 8sinst (V). Assume the initial voltage…

Q: 4. The length of x1(n) is N1, the length of x2(n) is N2. The coevolution of x1(n) and x2(n) has a.…

A: Note :- As per guidelines we are supposed to answer only first 3 questions (MCQ Type). So I request…

Q: Discuss the concept of unit-step, impulse and sinusoidal response and provide at least one example…

Q: Q2:- a) Find the error coefficient for the following system as shown in figure below: R(G) 100 (s +…

A: The system is is type 1 system hence only velocity error coefficient will be finite . The given…

Q: Given that x=3 and y =4 Determine a) The steady State error for a unit step input in terms of W and…

Q: What is the closed-loop function? What is type of the system? What is the steady-state error for an…

A: Since you have posted a question with multiple sub parts , we will solve first three sub parts for…

Q: What MPPT algorithm helps in pv optimization

A: PV(photovoltaic) Photovoltaics uses semiconducting material to convert direct light into…

Q: 02: For the pole-zero plot shown in figure Q2, answer the following a- Find the time response (y(t))…

Q: 1- By using MATLAB, connect the second order control system shown in figure below and draw the unit…

Q: Determine the steady-state output response of the causal system H(s) given below to an input x(t) =…

Q: Let G(s) = -K(s + 1)² s² +2s +2 with K > 0 in Figure P8.3. [Sections: 8.5, 8.9] a. Find the range of…

A: Given G(s)=-Ks+12s2+2s+2 with K>0. a. We need to find the range of K for closed-loop stability.…

Q: 4. Simplify the following expression using a 4-variable Karnaugh map: (a) in sum-of- products form,…

Q: Q3. Using K-map simplification method, simply the following Boolean function as sum of product (the…

A: Fw,x,y,z=∑(0,8,0,9,1,9) It is the four variable k-map so we have to take the grouping of maximum…

Q: Given two independent 1st order recursive systems with complex constant coefficients as described in…

A: Given, Two independent Ist order recursive systems, The impulse response of a system is…

Q: te the superposition théòřém. Why is the superposition theorem useful for analysis of…

A: Since you have asked multiple questions in a single request, we will be answering only the 1st…

Q: Q2- A- Find the static steady-state error shown by the system of open-loop transfer function…

A: The steady state can be calculated by using the general error signal representation and by using the…

Q: Q2: If the discrete time signal f(n) = 28(n+2) - 28(n+1) + 28(n) - 28(n-1) + 28(n-2), sketch. -2x(n)…

A: DISCRETE TIME SIGNAL- A Discrete-time signal or discrete-time signal is a time series consisting of…

Q: Find the stability condition of the equation given below. intervals of coefficients, what kind of…

Q: Perform a 200-case Monte Carlo analysis of the DAC as shown and find the worst-case differential and…

A: Given: The answer is shown as:

Q: Consider the real, frequency-domaln function Illustrated in the glven figure. -f If A = 1, 4 = 95…

A: Here, in the question, we have given continuous-time Fourier transform and we have to find inverse…

Q: Q5: impulse [r(t) = u1(t)] has the form, For the system shown in Figure, determine the values of K…

Q: Amplitude The output run of the following MATLAB code is n1=1; d1=[11…

Q: Digital Electronics and Design Question a) Minimise the function as shown picture below. b) Use the…

Q: * for the System in fiqure, find the coefficients Ki and Kz such that the steady-shate error is 5%…

A: In the control system, steady state error 5%. Find the value of k1 and k2 If the input is step…

Q: For the control system whose block diagram is shown below with G(s) = (2s2+8s+6)/(s3+6s2+8s): (a)…

A: The transfer function is determined as:

Q: 5. A L-R series circuit is built with inductance 10 H and resistance 4302 and connects to a electric…

A: The given circuit is a first order circuit which means only single energy storage element is exist…

Q: For the system with forward path gain s+2 G(s) = and feedback gain H(s) = s2+4s+7 8. will be…

Q: ASAP

Q: Find the stability condition of the equation given below. intervals of coefficients, what kind of…

Q: Derive the state variable model of the circuit given in Figure T5.3 if vo is the output. R, ic C R2…

A: Given: Brief description: In the above given question we have an electrical circuit having…

Q: s² + 420s Q(s) Pao(s) s² + 620s + 4000

A: Consider a unit step input. The expression for the transfer function is given as:

Question

Plz quickly

Y(s) =
Gas + bs + 2k)(s² + w²)
kos
Y(S)
(nks + bks+ 2)(s? + o²)
Cear my choice
We added the shown Pl controller to reduce the steady-state error of this system to become e 0.1 for a unit step
input. Determine Kthat allows us to do that. Hint start by finding the static position constant Kp.
RG
K.
2+
s(s+4)
s +3s +2s+3
plant
Pl controller
Select one:
O a.9.75
O b.6.75
O.9
O d. 13.5
1:
EN
CAMPOMATIC

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

5/The Voltage Regulation of a Transmission Line (in the simulator) depends on which parameter/s? A. Both the Transmission Line Resistance and Inductance B. The Transmission Line Shunt Capacitance only C. The Transmission Line Inductance only D. The Transmission Line Resistance only
Transfer function of the pulmonary system that represents alveolar pressure PA to Pao is given by H(s)=0.8s2 +4s+1. How much is PA for Pao = 5 mmH2O, at steady state in mmH2O?
Assume that the system recorded by the block diagram is reliable. a) Determine the position constant, kp, of velocity, kv, and of acceleration, ka, of the system. b) Determine the steady-state errors for a magnitude 5 input in step, ramp, and parabola, respectively.
Calculate the unit step input steady state error (ess) for the control system below. Examine the stability of the system given by the characteristic polynomial A(s)=2s³+4s²+s+1 using the Routh-Hurwitz criterion.
What is the effect on %VR value if taken at half-load lagging pf? Justify and explain briefly your answer on one(1) sentence.
By plotting the root locus of the system given as the open loop function : G(s)= K/(s*(s+2)); a) When K=4, show the locations of the closed loop poles on the root locus. Determine the Damping Ratio and Natural Frequency values in this gain value. b) Calculate the unit step response of this closed-loop system by calculating the Percent Overshoot, Peak, and Settlement Time values and plot them to scale. c) Scan the region on the root locus where the pairs of conjugate poles must be in order for this inspected system to work at least in the success criteria (greater than the calculated damping rate and natural frequency) in (a).
find vth , IN , RTH , between A and B , by using kirchhoff's law please write full detailed solution ,, thank you ,
(a) Assume the resistance is constant: R = 100.Check by direct substitution that the function VC (t) = 9(1 – e^−10t ) satisfies the ODE and the initial condition. (b) Now assume that the resistor slowly degrades, so that its resistance increases with time: R = R(t) = 100 + 2t. Solve the ordinary differential equation for VC (t) with this resistance, using either separation of variables, or the integrating factor method. Make sure to also include the initial condition.
G(s)= K / S^2+ 8S + 641 A) Calculate steady state error for this system? B) Design a controller to Improve the steady state error 2 times? C) Calculate steady state error for new controller? D) Draw the controller circuit with suitable circuit components?
Given the asynchronous circuit, determine the map Q1, Q2, Z, transition table, and flow table.
If the pole is located at the origin of the s plane, the response is in the form of a: a. damp exponential b. exponential rise c. sinusoid d. constant What characterizes an unstable system? a. poles at the origin b. poles with negative real part c. poles with positive real part d. poles without real part Routh’s stability criterion will provide the number of: a. RHP b. poles c. LHP d. imaginary poles
Consider the translational mechanical network system shown on the figure. A 1-lb force, f(t), si applied at t=0. If fv=1, find K and M such that the response is characterized by a 3-sec settling time and a 2-sec peak time. Also, what is the resulting %OS?