We need a three-stage space-division switch with N = 100. We use 10 crossbars at the first and third stages and 4 crossbars at the middle stage. a. Draw the configuration diagram b. Calculate the total number of crosspoints c. Find the possible number of simultaneous connections d. Find the possible number of simultaneous connections if we use one single cross-bar (100 x 100) e. Find the blocking factor, the ratio of the number of connections in c and in d

We need a three-stage space-division switch with N = 100. We use 10 crossbars at the first and third stages and 4 crossbars at the middle stage. a. Draw the configuration diagram b. Calculate the total number of crosspoints c. Find the possible number of simultaneous connections d. Find the possible number of simultaneous connections if we use one single cross-bar (100 x 100) e. Find the blocking factor, the ratio of the number of connections in c and in d

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter33: Single-phase Motors

Section: Chapter Questions

Problem 1PA

See similar textbooks

Similar questions

Find the missing values given the following information. R1= 1, R2=6, R3=6, R4=1, R5=2, R6=3, Vtotal=50 V
a- Define (with aid of a graph):Hold time, 5-variables Karnaugh map, -ve edge triggeredFlipflops.b- Draw & plot K-map of an odd function 4-variable XOR circuit.
Suppose in an IC fabrication factory there is conveyer belt from which workers collect the ICs & test There are 10 workers who are line-up with the belt and similarly the belt continuously moves and stops at ten different spots repetitively, so that each worker can collect his IC from it. You need to design such circuit with the help of Twisted Ring Counter using shift registers. Also draw the clock pulse diagram that represents the whole sequence for this counter circuit. Note: The counter has 10 states (initial state = 01010)
SohnCo. Baby Products Division purchases circuit boards from one supplier with a known failure rate of .06/year. In a new baby mobile, the university fight song module board has to be bought for a new supplier as well. After some testing, it’s discovered that the composite of the two suppliers results in a failure rate that is 80% higher. The failure rate, however, is decreasing over time.a) Estimate the failure rate of the new supplier’s circuit boards.b) What will the long-term failure rate be?
We need a three-stage time-space-time switch with N = 100. We use 10 TSIs at the first and third stages and 4 crossbars at the middle stage.a. Draw the configuration diagram b. Calculate the total number of crosspoints c. Calculate the total number of memory locations we need for the TSIs
4. Are the following statements correct or wrong? Justify your answer. (a) GTO requires very low current applied to its gate to be turn off. (b) IGBT is a voltage driven device. (c) BJT is more efficient than IGBT in high power applications. (d) Thyristors are used only for low voltage, low current applications. (e) MOSFETs are used for high frequency applications.
Q1.Please design a FSM to implement the basic function of onevending machine.a. You can insert two types of coins (1 yuan or 2 yuan)b. This machine can deliver one bottle of water worth 2 yuanGive the whole process of your solution: identification of input,output, state, stategraph, statetable, NextStateEquation, output equation and diagram of the circuit. Note (I have already answered it but i am not sure if its correct so can you write it in orderly manner ?)
design a two-way traffic light system with prototype using 4-bit down counter circuit. use 7-segment as an output to represent the timer.i need help.. pls make a circuit diagram for this. i will do this on the breadboardand also explain how u did it. thank youthe photo attached is how i will do it
Derive the Rs formula from the voltage divider formula. Show your steps. Given that the internal resistance of the batteries is very low, how would you make the calculations more accurate knowing the switch resistance? Do you think we should consider the leads and connector resistances to? Should those be added to the load resistor? Answer in full sentences what you think.
One of the major functions of transfer switches and equipment is to _____? A. Prevent the dangerous interconnection of two electrical systems that are not intended to be operated in parallel B. Provide a means of protecting the supply load from an over current condition. C. Allows for the ability to have the alternate electrical systems connected during normal operation. D. Allows for the ability to have both normal and alternate electrical systems connected during normal operation.
We have aquarium size 15 cm x 45 cm x 60 cm (L x W x H). Water must be replaced when: water level < 40 cm. Create proven Arduino with Tinkercad simulation on display LCD (include coding)?
Electrical Engineering 1. What voltage(s) should you provide when you power the Arduino through the barrel jack? How much current can be made available to the Arduino through this port? Does this port have any protection on it? 2. When you are powering the board using the barrel jack, what does the Vin pin do? 3. When you are powering the board using one of the ports mentioned above, how much current can you draw from the 5V pin? What about the 3.3V pin? What about a regular I/O (digital or analog) pin? 4. What voltage(s) should you provide when you power the Arduino through the Vin pin? How much current can be made available to the Arduino through this pin? Does this port have any protection on it? 5. What voltage(s) should you provide when you power the Arduino through the 5V pin? How much current can be made available to the Arduino through this pin? Does this port have any protection on it? 6. How much power does a normal 9V battery contain? How long could you run an Arduino board…