what are some vital parameters to be considered when siting a consumer unit/distribution board.

Q: What are some of the advantages of using high-tech lighting?

A: High-tech lighting : In high tech lighting system LED ystem are used for lighting purpose instead of…

Q: ock diagram of Arduino car Detector and explain operating

A: The Digital OUT of the first IR Sensor is connected to Pin 11 of Arduino and the Digital OUT of the…

Q: What is mean by equipment grounding and system grounding?

A: As per bartleby guideline for more than one question asked only first three are to be answered…

Q: What is external setup?

A: EXTERNAL SETUP: Setup is the method involved with setting up a machine to run an item. A portion of…

Q: What is meant by utility-controlled load management?

A: utility-controlled load management is the process to balancing the electricity supply on power grid…

Q: Explain the major consideration required for a protective system.

A: In the power plant, the generator is one of the most expensive pieces of equipment; therefore,…

Q: Sketch and compare the TNS, TNCS, and TNC earthing regulations as p wiring used to safe guard the…

A: 3)TNCS:- i)T- denotes that the Consumer is Solidly Earthed independently of the Source Earthing…

Q: explain/describe given full wiring circuit for “Prototype-Electric” Vehicle System!

A: A wiring circuit of Prototype-Electric Vehicle system is given in the question. We need to explain…

Q: Describe the functions of earthing/grounding in providing safety to user when a live wiretouches the…

A: Earthing: Earthing/ grounding is of low resistance wire and high melting point which prevents from…

Q: What are the three project categories an electrical contractor may choose to browse?

A: There are different projects in the world, and every project needs some specialty for completing it.…

Q: Discuss any two types of grounding methods.

A: Two types of grounding methods: Solid grounding Resistance grounding

Q: (b) Use labelled diagrams to illustrate the differences between a stand-alone and a power-grid…

A: “Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: What is embedded system?Also discuss the various applications of Embededded system.

A: we need to answer what is embedded system and also have to discuss the various applications of…

Q: What Are The Different Dimensions Of The Terms Engineering And Management?

A:

Q: Explain the Different types of testing Methodologies used in CB??

A: To check the rated characteristics and the capabilities of a circuit breaker, different types of…

Q: What is receptacle load ? Explain under 100 words...

A: The amount of load produced by a device inserted into a receptacle is referred to as a receptacle…

Q: What is the data and results that are shown in this picture?

A: To describe the data and result shown in the diagram

Q: What are the basic components of a module? Which components are mandatory?

A: The basic components are, Port list, Module name, Parameters, Register variables, Data flow…

Q: What materials and equipments are used when handling PCBs

A: PCB stands for Printed circuit boards

Q: Explain bus bar and bus bar chamber

A: In this question we will write about bus bar and bus bar chamber....

Q: 2) What are the salient features of supply voltage control method?

A: It is one of the control methodologies based on DC linking the supply voltage without any current…

Q: What is the voltage across the terminals of DS1 if a multi-tester set at 600V DC range is connected…

A: To answer above given question, we should understand the following circuit theory: Kirchhoff's…

Q: Estimate the relative error in measuring the unknown resistor when are using the Ammeter- Voltmeter…

A: Ammeter Voltmeter Method- The instruments required for this test are usually available in the…

Q: (b) Explain what is power system protection and why is it important?

A:

Q: Describe the job of the Board of Electrical Engineering in one sentence.

A: The solution is given

Q: 5. Explain the advantages and disadvantages of various types of grounding and indicate where each…

A: The system earthing refers to the earthing of the transformer and generator's neutral points. A…

Q: What should the K range be for the system to be stable

A: What should the K range be for the system to be stable?

Q: When designing and planning the Distributor, which parameter is taken into great consideration?

A: A distributor is a conductor from which tappings are taken for supply to the consumers.

Q: Choose one appliance/electronic device that needs application before it can be used and explain why

A:

Q: Do underwrites laboratories approve any electrical product for launch into the commercial market?

A: Underwriters Laboratories is one of the nationally recognized testing laboratories in the United…

Q: Discuss what is meant by zones of protection

A:

Q: What should the K range be for the system to be

A:

Q: THE TYPE OF WIRES AND WIRE GAUGES?

A: A wire is a single flexible strand of a metal, made up of materials which are good conductors of…

Q: What are the steps that must be taken in order to create a deployment diagram?

A: Given,  We have to write the steps in ordee to create a deployment diagram. Please find the below…

Q: What is the value of VR

A:

Q: Define the term passive reference configuration. When do we have this configuration when using…

A: When the current reference enters the positive terminal or polarity of the voltage source, then this…

Q: NO. A. Discuss the requirement of an efficient distribution system, describe the

A: Distribution system: The distribution system plays the main role in the calculation of consumer…

Q: 24. What value is to be considered for a "don't care condition"?

A: The correct option along with the explanation is provided in the following section.

Q: Define "ideal" and "currently available" standards and provide a brief explanation as to how they…

A: Ideal standards are principles that don't take into account typical wastage and work interference…

Q: 8. If DS1 busted/open, what is the voltage across the terminals of DS1 if a multi-tester set at 600V…

A: The given voltage across the terminals L and N is 220 V RMS.

Q: What are the differences between wrinkle method vs DO meter (advantages vs disadvantages)?

A: Different energy sources are required in day to day life. These energy sources can be renewable or…

Distribution System

The final stage in the delivery of the electric power is the electric power distribution system. From the transmission system to the individual customers it carries electricity. The distribution system is connected with the transmission system and is used to lower the voltage of the transmission to medium voltage in the range of 2 kV to 35 kV with the help of transformers. This medium voltage to the distribution transformers located near the customer's premises is carried by the primary distribution system lines. These distribution transformers in turn lower the voltage to utilization voltage used in lightings, household appliances, industrial equipments etc. Through secondary distribution lines often several customers are supplied from one transformer. It is through service drops, the commercial and residential customers are connected to the secondary distribution system lines. Customers who demand a larger amount of power can be connected directly to the primary distribution system level or the sub-transmission level.