What are the strengths and weaknesses of this Visceoelastic model?

Q: What are the steps to produce Plastic bottles of medical ?

A:

Q: Detailed information and report on Viscoelasticity

A: VISCOELASTICITY Visco elasticity viscoelasticity in material sicence is defined by : It is the…

Q: What are the differences between continuous or steady shear rheometry and oscillatory and creep…

A: The tension in shear rheology is tangential to the surface from which it is applied. The…

Q: Which has a higher strength, polystyrene with a DP of 1000 or a DP of 5000?

A: Degree of polymerization (DP) is defined as presence the total monometric units in a polymer. It is…

Q: Cement is made of crystalline particles of ___

A: In the question, It is asked about the crystalline particle of cement.

Q: What is woven asbestos friction material? Why asbestos friction materials are prohibited in many…

A: Woven asbestos friction material: It is friction lining materials which mixture of organic &…

Q: Using the ‘rule of mixtures’ calculate the modulus and strength,  in the fiber direction and…

A:

Q: . Why are recycling codes used in the plastic bottles?

A: As per bartleby guidelines we are allowed to solve only one question if multiple questions are…

Q: What two changes occur with regard to EAC behavior of PVC and polyethylene water and gas…

A: Polyvinyl chloride or the PVC is made by adding plastic and vinyl, so it is named polyvinyl…

Q: what temperatures sensonrs are best to measure the temperature of paraffin wax and why? ( give two…

A: INTRODUCTION: There are several varieties of Temperature Sensors available, each with unique…

Q: What is plastic impregnated (PI) wire ropes?

A: PI wire rope are basically platic filled wire ropes.

Q: Figure 9 is the adsorbent natural gas (ANG) vehicle tank to hold natural gas in an adsorbent at low…

A: In the vehicle sector, there has been a significant increase in the need for lightweight materials…

Q: Draw a stress vs strain rate curve for a shear thickening material. How does the viscosity of such a…

A: Shear thinking materials are known as dilatant materials. In this type of fluid viscosity of the…

Q: How is the characteristics of the stress-strain curve of concrete under axial compression?Please…

A: The stress-Strain curve for the concreate under axial compression loading is as shown in the above…

Q: If you need a plastic material for a product that must resist a variety of chemicals and affects of…

A: Fluorocarbon plastic will be chosen.

Q: What are the different types of Plastic Materials? Discuss each briefly (at least 4 types)

A: There are 7 different types of plastic materials are there They are: Acrylic or Polymethyl…

Q: A tempered glass window in an automobile requires two holes near the bottom edge, in order to attach…

A: In this problem, it is asking about the way to make holes during the manufacturing process in glass.…

Q: Is the laminated glass that is used for automobile windshields best described in terms of the…

A: The cracks in the laminated glass used for automobile windshields generally initiate in the outer…

Q: Using information acquired from the National Transportation Safety Board (NTSB), explain the role…

A: At 11:00 pm on July 10, 2006 a 1991 Buick passenger caroccupied by a 46 year-old male driver and his…

Q: General information and report on Elasticity and Viscoelasticity

A: General information and report on Elasticity  Viscoelasticity

Q: Magnesium oxide particles are compacted and fired at a high temperature to produce a strong ceramic…

A:

Q: Which type of glass is widely used with good electrical insulating ability and good strength?

A: Answer : E-glass

Q: Define and discuss Blow molding Process in Metal and Plastic. Does blow molding can be use in Glass…

A:

Q: For the case of a perfectly plastic

A: Given: The maximum reduction in cross-sectional area per pass (R) of a cold wire drawing process is:…

Q: Question 2: Calculate the APF for polyethylene. Given the volume of unit cell is 0.09333 nm³ re…

A:

Q: ) To calculate the tensile strength of the fibre, the cross-sectional area has to be determined.…

A: given:

Q: Question 6. Calculate the average molecular weight Mm for a thermoplastic that has the following…

A:

Q: What is Poisson's ratio ? why do you think is it lower for ceramics and higher for polymers compared…

A: Poisson's ratio is the ratio of transverse strain to the axial strain.ϑ=-εtransεaxial

Q: In general, polymers have lower strength, hardness, stiffness, density, and temperature resistance…

A: This statement is true.

Q: What are the types of biomaterials? What is the main property of a biomaterial?

A: Biomaterials are generally grouped into three classes: metals, ceramics, and polymers.

Q: Question 7. The nose cap and the wing leading edges of the space shuttle may reach temperatures of…

A:

Q: How did the consistency of the jelly change when you changed the ratio of sugar to pectin?

A: Pectins are the extracts obtained from the fruits. The jelly of the fruits extracts used to make…

Q: As the lead engineer for a LPG storage project, you are overseeing the design of pressure vessels…

A:

Q: elastic modul

A: given: What is relation between bulk modulus and elastic modulus?

Q: What factors influence the crystallinity ofpolymers? Explain the development androle of…

A: The process of partial alignment of their molecular chains is called the crystallization of…

Q: If the viscosity ofCl2 gaseous molecule at 20.0 °C and 1 atm. is 132 pP. what is the viscosity of dz…

A: Given data: The viscosity of 35Cl2 at the given temperature and pressure conditions is v1 = 132…

Q: What are the typical post treatment for plastic materials?

A: The main purpose for treating the components after the processes like printing is to decrease the…

Q: For an application of high strength components including gears cams and rollers the desired…

A: Given: For an application of high strength components including gears cams and rollers the desired…

Q: For materials selection, determine the type of material that will give the minimum thermal…

A: Diamond has excellent thermal conductivity and low thermal expansion , which leads to minimal…

Q: Most ceramics materials are immune (resist) to corrosion because: they are chemically stable and…

A: Most ceramics materials are immune (resist) to corrosion because: they are chemically stable and…

Q: A carbonate whole core 700 cc is placed in cell two of a Boyles Law device. Each of the cells has a…

A: According to the given details provided.