It is known that q = 3kN/m; F = 6-√√2kN and M=10kN m. Ignoring the weight of the frame, determine the constraint reactions at the fixed end A. F M A 3m 45° 4m

Q: A flat plate is placed normal to a discharging jet of water. The jet discharges water at the rate of…

A: Flat plate normal to discharging jet of water- Discharge from jet Q= 0.2 m3/s Speed of water V= 18…

Q: A channel of width 450 mm branches into two sub-channels having width 300 mm and 200 mm as shown in…

A:

Q: Question-18 A saturates soil mass has a total density 22 kN/m3 and a water content of 10%. The bulk…

A:

Q: Using ASIC tables AS 1204 Table 3 and 4 as well as ASIC design capacity tables, what is the yield…

A: AS 1204 Table 3 provides the mechanical properties of structural steel sections, including the yield…

Q: Q1) In this connection E60 electrode has been used and a weld size of ½ inch connects this corbel to…

A: Size of the weld, a= 1/4 in = 0.25 in Applied load, P = 120 kips Strength of Electrode used = E60 =…

Q: Draw the shear and moment diagrams for the beam.

A:

Q: (12-16) MOMENT DIAGRAM (DON'T FORGET TO PUT LABELS, UNITS, AND DEGREE OF CURVE CONSTRUCT SHEAR AND…

A: Given : Required : Moment diagram

Q: An air conditioner cools humid air at temperature t₁ = 25°C and relative humidity 1 = 70% to…

A: To solve this problem, we can use the psychrometric chart, which shows the properties of moist air,…

Q: Design an earthen canal to carry a discharge of 40 cumecs and the mean diameter of silt particles is…

A: Canal discharge(Q) = 40 cumecs Mean diameter of silt particles (d) = 0.3 mm Design the earthen canal…

Q: 1. A sample saturated cohesion less soil tested in a drained triaxial compression test showed an…

A:

Q: A symmetrical circular arch of span 25 m with a central rise of 5 m is hinged at crown and…

A:

Q: si, determine the maximum load P that may

A: ###Calculation of the Load P which can withstand the allowable SHEAR in Beam###

Q: For 100 sq. m cement concrete (1: 2: 4) 4 cm thick floor, the quantity of cement required, is

A: →thickness = 4cm→Area of cement concrete =100m2→sum of ratio of concrete mixture =1+2+4=7To…

Q: Figure SIN 72 < 1 of 1 ▾ Part A Determine the equation of the elastic curve for the beam in (Eigure…

A: Equation of elastic curve

Q: Calculate the bar force members IJ, ID, LK and BC using method of section. ANS: IJ = 4.6 KN (C) ID =…

A: Given: A truss with loadings  Required : Force in member  IJ, ID, LK, BC

Q: differentiate between saturated and unsaturated flow in soils

A:

Q: A beam AB is fixed at both ends and carries a uniformly distributed load of intensity p per unit…

A:

Q: Draw the free-body, shear and bending moment diagrams of each member of the rigid frame shown.

A: ###Drawing of free body diagram , SHEAR force diagram and BENDING moment Diagram ####of frame

Q: Determine the size in ft of a circular vitrified pipe sewer which will be used to discharge 15 cfs…

A:

Q: a) criteria, hazardous (b) hazardous, criteria, (c) toxic, particulate (d) PM2.5, organic

A: Criteria air pollutants are air pollutants for which acceptable levels of exposure can be determined…

Q: Determine the net area for the plate PL // x9 with 3/4 in bolts indicate which area controls

A: Diameter of bolt = 3/4 in Number of bolts, n= 6 Size of plate = 1/2' * 9' It is asked to determine…

Q: 3. For a saturated sand deposit, the void ratio and the specific gravity of solids are 0.70 and…

A: void ratio e = 0.70 specific gravity G = 2.67 The critical upward hydraulic gradient=?

Q: Use the virtual work method to determine the vertical deflection at joint C Acy of the frame shown…

A: ###Calculation of Vertical deflection at Joint C using Virtual Work / Unit load method of analysis…

Q: 37. 38.

A:

Q: 1. The maximum density corresponds to (maximum/minimum)_ 2. An increase in the degree of saturation…

A: Note- It has been asked to solve question 7. Sand Cone Method- In this method, a hole is dig and…

Q: 1. The maximum density corresponds to (maximum/minimum). 2. An increase in the degree of saturation…

A: Triaxial test- This test is done on a cylindrical core soil sample to find its shear strength.

Q: CVE 331 Consolidation Settlement Calculation Problem 1: A rigid concrete foundation is shown in a…

A:

Q: An open ended steel barrel of 1 m height and 1 m diameter is filled with saturated fine sand having…

A: An open-ended steel barrel- Height = 1 m, &amp; Diameter d = 1 m, Drop in the water level h = 0.75 m…

Q: Determine an expression for the vertical reaction at Point A.  Note: this will be a function of x.

A:

Q: VIII) A force of P = 400 N is applied to the 70-kg cart. Determine the reactions at both the wheels…

A:

Q: Velocity measurement of flow through a rough circular pipe indicate that the average velocity is…

A:

Q: C 4' * -A 8' 3200 lb/ft 4' 기 B

A:

Q: Draw the Influence Line Diagram of the maximum moment at Point E of the given simple beam as ME = f…

A:

Q: 8. For the beam and loading shown, determine the reaction at the roller support. The beam is…

A: Beam: Section: W 250 x 25.3 Load density: wo = 2 kN/m Length of the beam: L = 9 m Young's modulus:…

Q: 4. What are the major forest products that people use?

A: "Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: Use the virtual work method to determine the vertical deflection at joint C of the frame shown

A: ###Determination of Virtual deflection at joint C of frame ###

Q: For a design speed of 60 kmph, if the deviation angle of a valley curve is 1/30 then the length of a…

A:

Q: The 10m long beam shown in the figure has a total superimposed load of 40 kN/m and the prestressed…

A: Length of beam, L=10 m Unit weight of concrete, γ=23.5 kN/m3 total superimposed load (Live load),…

Q: lable 5.2 Unified Soll Classification System (Based on Material Passing 76-2-mm Sieve) Criteria for…

A: Passing from sieve 200 =17% Passing from sieve 4=100%  it means sieve belongs to sand  fines are…

Q: A concentrated vertical load of 3000 kN is applied depths 1 m and 2 m below the ground, respectively…

A:

Q: (a) Solve the following indeterminate beam by the moment distribution method. Determine the…

A: To determine the reactions and to draw the bending moment diagram. Note: Since the Question has two…

Q: 1 : Find the deflection of the simply supported beam of 12 m span, and then compare with ACI Code…

A: To find the deflection of a simply supported beam, we need to determine the maximum moment and the…

Q: Given data: I = 14° R = 50m D = 1° interval until 7° L (length of chord) = from 1° -7° Solve for: 1.…

A: I = 140 R = 50 m D = 10  Find: (a) Tangent (b) Length of chord for every degree from 10 to 70

Q: Calculate the value of double area if the value of latitude of A is 235.67 m and DMD is +89.26 m.

A:

Q: The water content of a saturated soil and the specific gravity of soil solids were found to be 30%…

A: A saturated soil- water content w=30%,specific gravity G=2.70,unit weight of water γw=10 kN/m3,To…

Q: 1. Draw shear and moment diagram. Determine maximum moment and maximum shear. 20 KN 30 KN/m K 2.0 m…

A: Given: Required : Shear and moment diagram.  Maximum moment and maximum shear Note: As per bartleby…

Q: A 1,200-mm diameter transmission pipe carries 126 l/s from an elevated storage tank with a water…

A: diameter of pipe = 1200 mm  Water surface elevation of reservoir = 540m  pipe length under…

Q: A highly turbid water at 20⁰C is to be treated in a sedimentation (gravitational settling) tank…

A: Let t be the time required for suspended particles to settle at bottom of sedimentation tank. t =…

Q: Using the method of work and energy, determine the slope at point D caused by the couple Mo. (Round…

A:

Q: what size of pipe in ft should be used?

A: ###Calculation of size  D of pipe in ft  for circular vitrified sewer pipe having discharge 83.50…

Frames

The trusses and frames are the two most important structural members of civil engineering. Trusses are the interconnection of links and other structural members. The interconnection with other members makes the system behave as a single member that supports and transfers loads. Trusses are generally two types, plane truss, and space truss. Frames on the other hand form the skeleton of any building construction. Frames are structures formed by the connection of beams, columns, slabs, and joists. These members provide the building with the required structural support.