What function does this implement? Draw the timing diagram

Q: why do flip flop work because the feedback allows 2 stable states?

A: Latch is basic sequential circuit. The output of latch change as input changes. It is level…

Q: Write a program to generate the following Timing Diagram with the order: Step 1-A button is pressed…

A:

Q: Differentiate the two types of instruction in PLC. COUNT UP COUNTER, COUNT UP/DOWN COUNTER

A: We need to differentiate between the two types of instruction in PLC. COUNT UP COUNTER COUNT…

Q: 7. What is the difference between an electrical concept and a PLC concept?

A: Basically electrical concept deals with the generation, transmission, distribution and utilisation…

Q: Answer one of the following A. What are the basic types of timers in PLC? B. What are the types of…

A:

Q: Describe the function of each block of a typical PLC in a brief way. Include labeled diagram

A: The above shown diagram is generalized block diagram of programmable logic controller (PLC) It…

Q: clk Qo Q1 Q2 T1 T2 T3 T4 Ts Based on the timing diagram, what device is this? O PIPO shift register…

A:

Q: A time-proportioning (PWM) controller with a DC output voltage of 35 volts will produce an average…

A: This problem is from power electronics  Look for solution in next slide

Q: Draw the internal circuit of 555 timer IC, and explain how it operate.

A: The IC 555 timer circuit is shown below: The internal circuit of the IC 555 timer is shown below:…

Q: the

A: Let us assume initially A, B & C are zero.

Q: 6. Sketch the wiring to connect a power supply and PNP sensor to the PLC input card shown below. 00…

A: The connection of the power supply and the PNP sensor to the PLC input is shown below in the…

Q: Identify the process happen in Figure Q29(a). Interrupt User Program Handler X Interrupt Handler Y

A: The process shown in fig. is defined as the bending waves around the corners of an obstacle or…

Q: For the given details, Clockrate = 900 MHz, Instructions executed = 1200, Machine instruction = 30…

A:

Q: 4)Comparison instructions A)may be combined in AND (series) as well as OR (parallel) configurations…

A: To execute the comparison instructions, the combination of the AND and OR gates is required. The OR…

Q: How many different ways can interrupt triggering be done? What are these?

A: Interrupt - Basically interrupt is a block of an instructions which is associated with a specific…

Q: Study the ladder logic program in figure below and answer the questions that follows: a) What type…

A: Answer-

Q: 1. Sp Sp Sp Rp Vec Clock input Aulurmatic Reset From the circuit, write the output value Q2 (logic…

A: According to the question, for the given circuit as shown below We need to find the output Q2.

Q: eedback and control system Explain how a closed-loop automatic transfer switch (ATS) operates, and…

A: An automatic transmission switch (ATS) is a device that automatically transmits power supply from…

Q: Q3: Consider a digital counter that counts 5 to 0 when the reset button is 0 and go back to 0 when…

A:

Q: Q1.) The state diagram for a negative edge triggered counter is shown below. Sketch the…

A:

Q: Discuss two modes of 555 timer with circuit diagram and proper equations. Provide two applications…

A:

Q: Describe clocking methodology.

A: Clocking methodology   Clocking Methodology defines the timing when data (signal) is being read and…

Q: 4)A PLC scan cycle contains each of the following operations EXCEPT A)read inputs B)perform…

A: PLC's will work by scanning the program continuously, by doing this plc scans the hardware and…

Q: Q2: What is the maximum clock frequency that the control that can used? If time delay is 30 ns to…

A: Given time delay=30 nstransfer address=20 nsaddress register=20 ns

Q: 1.a. In a DC servo motor system, the tachometer feeds back a voltage that’s proportional to motor…

A: 1.a) Tachometer is a device that produces signal proportional to the speed. Tachometer senses the…

Q: Mechatronics 37.

A: We need to find out the output for given logic diagram

Q: Q1.) The state diagram for a negative edge triggered counter is shown below. Sketch the…

A:

Q: Q3: Consider a digital counter that counts 0 to 7 when the reset button is 0 and go back to 0 when…

A:

Q: 6.draw the timing diagram for the following 8085 instructions and also determine the time taken to…

A:

Q: which option is the Q2Q1Qo value given correctly after 14 clock pulses in the following digital…

A:

Q: (a) Is this a Mealy machine or Moore machine? (b) Fill in the outputs on the transition table. (c)…

A:

Q: • Create a new relay logic that will simplify the logic below. + A B C HH #HE D # C * A B #F (M) DC…

A:

Q: Industrial Motor Controls 14.a. Single sweep operation of a PLC is normally used to A. produce…

A: Answer 14 (a):   Normally, a PLC's single sweep action is used to debug newly built ladder logic.…

Q: The symbol used for normally close contacts in PLC is

A: The explanation is as follows.

Q: B. What are the types of counters in PLC?

A:

Q: 8.2 A logic circuit with active-low synchronous reset has two control inputs x and y. If x is 1 and…

A: Given control Input  x and ygiven  x=1, y=0 then   R←R+1    and    s1→s2x=0, y=1,  then R←0  also…

Q: What is the purpose of clock pulses?

A: Clock pulse: Clock pulse is a timing signal used to synchronize the activities performed by digital…

Q: 3. Describe working of different proximity sensors used in a PLC.

A: The sensor that is used to determine the object in a specific range is known as the proximity…

Q: Could you perhaps clarify what a programmable interval timer/counter

A: In this question we will write about programmable interval timer ....

Q: om our experiment we used LM555 timer to demonstrate a multivibrator circuit. The following choices…

A: We need to select correct option .

Q: Explain how a timing circuit works and list some applications.

A: Timing circuit : Timing circuit is a electronic circuit which synchronize any signal with the help…

Q: In how many different ways can interrupt triggering be performed? What are they?

A: There are different-different ways of interrupt triggering and they are as following, 1. Hardware…

Q: 21.a. What type of circuits are present on an axis logic card for a stepper motor system and are…

A: Given; The objective is to find what type of circuits are present on an axis logic card for a…

Q: Design a PLC program and prepare a typical I/O connection diagram and ladder logic program for the…

A: In the question, the following data is given. A motor named M and three controlling START/STOP…

Q: In a DC servo motor system, the tachometer feeds back a voltage that’s proportional to motor speed.…

A:

Q: نقطة واحد؛ Which of the following statements is NOT correct (25) If a problem in a PLC module…

A: A PLC is a programmable logic controller. It is basically a computer used for controlling the…

Q: 24)A PLC scan cycle contains each of the following operations EXCEPT A)read inputs B)perform…

A:

Q: The power required to operate the logic circuits of the processor unit (8) :is Low voltage ac High…

A: