What is a hazard of push buttons

Q: X) Answer the following questions (answers to be typed, handwritten answer for this question will…

A: The answer is

Q: Question No. 1: [10 Marks] [CLO-1] Draw only the block diagram to demonstrate the complete PCB…

A:

Q: 2. An actuator slowly extends as the push button is pressed. Upon the cylinder reaching a certain…

A: To draw the electrical as well as pneumatic circuit

Q: Please solve this question in control system quickly

A:

Q: Given the image below, what are the control signals needed to perform the NOT operation (OR (x, y)).

A: The control signal needed to perform the NOToperation (OR(x,y) ) are:Since,zx =1, then x = 0, the…

Q: What happened to the led speed blinking when the delay was changed?

A: /* Blinking LEDs- Program to run that the LED is connected to pin 6 and the delay is one second…

Q: Q.33 True or false? A normally closed push-button symbol is drawn so that the movable contact is…

A:

Q: ‏List the flags that would be affected during the use of IN instruction.

A: In this question we will know about the flags that would be affected during use of instruction....

Q: Draw a simple block diagram of 'Open-Loop Control System' and 'Closed-Loop Control System' Not…

A:

Q: ow does an intermediate switch work?

A: The explanation is as follows.

Q: A washing machine is supplied with hot and cold water from two different supplies. Draw the bock the…

A: Given, Two inputs with cold and hot water supply. The flow of hot water as well as the cold water…

Q: Explain different types of ADC with figures?

A:

Q: Crosstalk, shielding and grounding

A: According to question: Crosstalk: It is one of problem seen in communication system which occurs…

Q: or a jet pump which is larger the drive pipe or the suction pipe

A:

Q: Aside from the examples given in the notes, give 3 more examples of automatic control systems using…

A:

Q: What is the difference between the pins under number 1 and the pins under number 4, and mention when…

A: Group numbers 1 and 4 are general-purpose input and output pins of Arduino and they are grouped…

Q: Deep freezing of wet documents does what

A: Solution The fruitful recuperation of water-harmed library and documented materials relies upon…

Q: Signals and systems (Please write in legible handwriting if it is handwritten)

A:

Q: What is the difference between a task and a function in verilog?

A: As per our company guidelines we are supposed to answer only first one question. Kindly repost other…

Q: Why are certain operations blocked by isolators?

A: Isolators are material for high voltage gadgets like transformers. The principle capacity of…

Q: Report: Answer the following 1- What is meant by Registers? Do they have names?

A: According to our guidelines, we can answer only one question at a time. Kindly, repost the remaining…

Q: AIWhat is the difference between clippers and clampers ? sketch the * .circuit

A:

Q: Compare between the status and control flags? Explain the status flags for the operation AEH+37H

A: Status flag show the status of the microprocessor accumulator after an arithmetic or logical…

Q: What is the modus operandi motion control lamp Please not handwriting

A: the modus operandi motion control lamp

Q: Briefly explained the function of the hold device in a digital control system.

A: The hold device is used to convert discrete signal into continuous or analog signal which can be…

Q: 1- What does the air volume sensor mean? What are the electrical lines of this sensor, explain?

A: Note: As per the guidelines will be solving only 1st question. For others please repost. Generally,…

Q: Basic Control Actions 1) What is the most used controller?

A: We are authorized to answer one question at a time, since you have not mentioned which question you…

Q: Compare between indirect and direct control circuits.

A: Indirect control circuit : Cylinders with large piston diameter have a high air requirement. Control…

Q: A proportional system of control system. How to disable OFF-SET ? Draw example for Process line…

A: The oscillations around the set point (known as oscillation) in some processes may be too severe to…

Q: High Voltages are preferred for Transmission of Electricity. Why? Note please do not handwriting

A: Power transmitted from the one place to other places at the higher voltgae levels .

Q: Explain the used of Drum Switches? Draw the 6 point , 8 point and 9 point drum switches?

A:

Q: f I were to fill in the table to have a robot follow a line being detected by the three sensors, how…

A:

Q: Where push-buttons are being used in our daily lives? State some examples.

A: Given: Push button

Q: 3. Compare between indirect and direct control circuits.

A: Indirect control circuits: Cylinders with a big piston diameter demand a lot of air. To activate…

Q: What is analog switch?

A: An analog switch is also known as bilateral switch which is similar to relay with no moving parts.…

Q: What is the function of a sensor and an actuator in a mechatronic system? List different types of…

A:

Q: push buttons

A: it is a momentary contact. just aplly to make a contact. it is used in various electrical system.

Q: Question: Describe the functionality of the following buttons and LEDs on the front panel while…

A: An analog input or digital interface is used to remotely regulate the functioning of a programmable…

Q: List the flags that would be affected during the use of IN instruction.

A: The IN instruction is a kind of mnemonic which is used for the input in microprocessor. It input the…

Q: How do the different parameters vary with ic?

A:

Q: Aastion 19 Which of the following explanation is NOT true? Select one: O a. A measurement system is…

A: 20)  Mechatronic system consist of mechanical, electrical and control system. First controller is…

Q: 9 Answer the following questions (answers to be typed, handwritten answer for this question wi not…

A:

Q: explain Each block for a Manipulator Robot on a block diagram

A: Robotic manipulators- Robotic manipulators are capable of performing repetitive tasks with speed and…

Q: 1) The Execute Unit (EU) functions? 2) Compare between status & control flags?

A: In this question , we will write about execute unit, status flag and control flag..

Q: What is the difference between an LEA SI,NUMB instruction and a MOV SI,OFFSET NUMB instruction?

A: An instruction of a computer is a command given to the computer to perform a specified operation on…

Q: Following error

A:

Q: What is the difference between a one function and a multifunction electronic control device

A: A one function electronic control device operate only one function, Those equipment which uses…

Q: Differences between VFD and Soft Starter,include their applications and when are they used

A: To differentiate between VFD and Soft starter

Latches and Flip Flop

Just like logic gates, the latches and flip-flops are the important elements of an electronic circuit. The logic gates form the important part of combinatorial circuits, while the latches and flip-flops form the essential part of a sequential circuit. Sequential circuits form the important concept of automata theory in electronics and electrical engineering, these circuits are a kind of logic circuit whose output depends on both present input and past inputs, that is, the input history.