What is the answer in #3B. Show complete solution and FBD

Q: Each of four particles move along the x-axis. Their positions (in meters) as functions of time (in…

A: Introduction In this problem we will calculate the velocity and acceleration of the particle and we…

Q: A marksman fires a practice round from A toward a target B. If the target diameter is 170 mm and the…

A:

Q: ius rB = 199 mm, and is at rest when it comes into contact with disk A. Knowing that μk = 0.45…

A: Given data as per question Disk A has mass mA = 4.5 kg, radius rA = 278 mm, and initial angular…

Q: A 2-kg sphere is attached to a massless rigid rod attached to a fixed pivot point O. The rigid rod…

A: Given data:- Mass of the sphere (m)=2kg M=0.5t2 N-m Length of the rod (l) =0.5 m To find:- Speed of…

Q: Steam enters a turbine at 10 MPa and 600°C and exits at 0.1 bar. If the isentropic turbine…

A:

Q: A. Draw a different configuration, and make it a diagram similar to Fig. 3. Specify each mass and…

A: Given: To find: A. Draw a different configuration, and make it a diagram similar to Fig. 3.…

Q: Determine the angular velocity, in rpm, of the rotating drum which results in loss of contact…

A: Given data:- Angle=0.9699 rad, and Radius (r) =330 mm To find:-angular velocity of drum

Q: In a basketball game, the point guard A intends to throw a pass to the shooting guard B, who is…

A:

Q: The normal and shear stresses in MPa at point P are respectively a) 67.9 and 56.6 (b) 56.6 and 67.9

A: Given data:Force applied, F=600 NDiameter, d=30 mm

Q: Three equations of equilibrium are available to determine the unkowns. -Two dimensional force…

A: Three equation of equilibrium consist of the balance of forces in two dimensional and moment balance…

Q: Stiven AL in diameter Red 180 in long elongates 0.12 in under load of 60 kip. The diamurer of Rod…

A: Given    Diameter, d = 2 in        Length, L = 100 in           Load, P = 60 kip Find   Modulus of…

Q: Compute the allowable load in kN on a 20mm x 120cm long steel rod with a maximum elongation must not…

A:

Q: y did we use 3498.28 N in computing for the total elo

A: We have givenThe maximum shearing stress in either spring must not exceed 200 MPaτmax=200 MpaFor…

Q: Problem no. 1. Compute the reaction forces at pt. A and B D C 9 m B 3m 1.5 m 3 m 30° 20 KN

A:

Q: a pipe varies jointly with the internal pressure and the diameter of the pipe, and inversely with…

A: Given data as per question The stressσ in pipe varies jointly with the internal pressure(P) and the…

Q: A 372-kg boat is sailing 15.0° north of east at a speed of 1.60 m/s. 34.0 s later, it is sailing…

A:

Q: ble containing the ideal gas specific heats of various common gases. diffe Uko K

A: Given data as per question P1=150 kPa, T1=39°C P2=150 kPa, T2=337°C

Q: pitch of gears A and B is 3.125 mm and of gears C and D is 2.5 suitable numbers of teeth for the…

A: Given-Information:- Speed Ratio, NAND = 12mA = mB = 3.125 mm mc = mD = 2.5 mm To-Determine:-…

Q: determine the properties of the saturated liquid at 10 bar. Locate the state on a T-S diagram

A: Given data:- the saturated liquid at 10 bar To be found out :-the properties of the saturated liquid

Q: A flat steel plate that weighs 1.0 N is resting on top of an aluminum ball which is resting on a…

A: Solution: Given Data: *The weight of the steel plate, W=1 N *The diameter of the ball is, D = 100 mm…

Q: any way the solution set c

A: Lead and aluminum both have FCC crystal structures  Density of solid aluminum= 2.71g/cm3.

Q: A projectile is launched from point A with speed vo= 33 m/s. Determine the value of the launch angle…

A:

Q: If your drive gear is 36 and your driven gear is 60, what is the gear ratio? O 60/1 O 3/5 O 36/1 O…

A: Given : Number of teeth on drive gear , T1 = 36 Number of teeth on driven gear , T2 = 60   To find…

Q: Ex find The fuel used (gramor kg) in one year in d 1424.24 kw reactar کو معطل بور 235

A: The mass of U235 fuel used in one year is 547.64 grams.

Q: Problem 1: A cone-plate viscometer is a device used to measure a fluid's viscosity. The torque M…

A: Solution; The toque M is given as: M=f(Ω,R,θ,μ) here, Ω is the angular velocity with unit rad/s and…

Q: The rotation of the 3ft arm OA about O is defined by the relation θ=0.15t2, where θ is in radians…

A:

Q: Calculate the total head of the system below. Assume a flow of 70 m³/h and that the pressure drops…

A: GivenZA=15mZB=5mZC=5mhs=3mhd=4m

Q: Water is the working fluid in a reheat-regenerative Rankine cycle with one closed feedwater heater…

A: Schematic diagram Given data: P1=P11=P10=1440 lbf/in2T1=1100FP2=P3=P4=P12=500…

Q: At time t = 0 a small ball is projected from point A with a velocity of 287 ft/sec at the angle 63°.…

A: Introduction With the use of the equation of motion, we will compute the times t1 and t2 in this…

Q: Initially contains Air: P1 = 30 lbf/in^2 T1 = 540 °F V1 = 4 ft^3 Second phase of process involving…

A: Given data:-air piston cylinder with work and heat interaction system To be explained:- potential…

Q: 2) Explain the in detail control system for steam supply to the engine of centrifugal Watts’Governor…

A: Steam supply can be controlled by a governor. In centrifugal watt governor flyballs are balanced by…

Q: The vena contracta is the section where this minimum flow area occurs in a sudden contraction

A:

Q: Given: The plate( The shaded rectangular volume) has weighs 240 lbf. It is. suspended by able CD,…

A: Given: To find: Tension in cable CD

Q: A 1-kg mass is attached to a spring with stiffness 1 N/m. The damping constant for the suystem is 2…

A: Given data: massm=1 kgspring stiffnessk=1 N/mdamping constantc=2 N sec/minitial velocityv=30…

Q: Thermodynamics- During an isentropic expansion process of 1.2 kg/s of air from 8 bar to 1 bar a)…

A: Given Data- m=1.2kg/s P1=8bar P2=1bar T1=485K We have to find Volume and final temperature

Q: Determine the support reactions and draw the Shear and Moment Diagram. Note: All upward forces are…

A:

Q: The 15.8-in.spring is compressed to a 6.0-in. length, where it is released from rest and accelerates…

A:

Q: EXPERIMENT (2): LINEAR HEAT CONDUCTION/practical heat transfer Discussion: 1-State any possible…

A:

Q: Determine the support reactions and draw the Shear and Moment Diagram.

A:

Q: A cylinder of internal diameter 2.5 m and of thickness 5cm contains a gas. If the tensile stress in…

A:

Q: In a basketball game, the point guard A intends to throw a pass to the shooting guard B, who is…

A:

Q: Process A: A piston-cylinder assembly, the piston was welded to the cylinder on both sides.…

A: For solution refer below images.

Q: 200 N/m 70° 50 N/m 120 N/m 125 N/m F Ans:

A:

Q: Problem 2. (Determining Cutting Speeds in Machining Economics) A turning operation is performed with…

A: “Since you have asked multiple question, we will solve the first question for you. If youwant any…

Q: The graph in the figure shows the position of an object as a function of time. The letters H-L…

A: Given, Position time graph of the object is given indicating its position at various times.

Q: Auditorium Hall is to be maintained at a temperature of 24 C dry bulb temperature and 60 % relative…

A:

Q: The figure below shows a small gate attached to two couplers. The door needs a resultant moment of…

A: Given data: MA=178 N.mF1=480 N Need to determine the magnitude of the force F2 necessary for the…

Q: A car is moving on a curved horizontal road of radius 100 m with a speed of 20 m/s. The rotating…

A:

Q: Determine the maximum absolute value of the shear.

A: Given: P = 6.5 KN To find: | Vmax |

Q: k = Let (x, y, z) p> 0. Is (x, y, z) harmonic? with p = x² + y² + z². Find the level sets of and F =…

A: Solution: Given Data:

Free Body Diagram

The system of forces acting on a body tends to either rotate it or make the body undergo motion. In general, when an external agent exerts a force on a body, the body undergoes translational motion and rotational motion. The body has six degrees of freedom under the influence of that force. Here, three degrees of freedom are from the translational motion while the other three are from the rotation motion. However, sometimes the bodies are not allowed to undergo any motion and are fixed, under such conditions the body is said to be constrained.