A cylinder buoy is 1.2 m in diameter and 2mhigh weighing 800N was being held stableby a cable connected to a 0.5 m3 anchorblock weighing 24kN in air. The cylinderfloats in seawater with a draft of 0.3m.Specific gravity of seawater is 1.03.What is the bouyant force on thecylinder(kN)?Determine the tension in the cable if thetop of the cylinder is 0.6 m above the watersurface(kN).Find the rise of the seawater to move theblock from the seabed(m).

Buoyant Force= Weight of fluid displaced Weight of fluid displaced = Density * 9.81* Volume of water…

What is the bouyant force on the cylinder(kN)? Determine the tension in the cable if the top of the cylinder is 0.6 m above the water surface(kN). Find the rise of the seawater to move the block from the seabed(m).

What is the bouyant force on the cylinder(kN)? Determine the tension in the cable if the top of the cylinder is 0.6 m above the water surface(kN). Find the rise of the seawater to move the block from the seabed(m).

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: For a simply supported prestressed concrete bearn, compute the stress in the top fiber at midspan du...

Q: The gross commanded area of an irrigation canal is 10 x 103 ha out of which 8 x 103 ha is culturable...

Q: Problem 1 The cantilevered rectangular bar is subjected to a force of 9 kips. a. Determine the major...

Q: . Bronze pipe (1) has an elastic modulus of E1 16,000 ksi, a cross-sectional area of A1 2.68 in m al...

A: Given data ∆=0.25 inPipe 1 Pipe 2E1=16000 Ksi ...

Q: - Stabilized soil brick is made from clay mixed with a small percentage of some stabilized materials...

Q: The sanding-drum mandrel shown in the figure is made for use with a hand drilI. The mandrel is made ...

A: a)The change in strain along a diameter is found from εD=∆DD=1.60 in.-1.50 in.1.50 in.=0.0667 in./in...

Q: A solid circular bronze [G = 6,500 ksi] shaft, 5.8 ft long and 1.275 in. in diameter, carries a torq...

Q: 103. What is the quantity (Sq.m) of plastering required for the 6m length of wall which is 4m high a...

A: given-length of the wall=6 mheight of the wall=4 mthickness of the wall=50 cm

Q: Use the graphical method to construct the shear-force and bending-moment diagrams for the beam shown...

Q: SITUATION. A mercury barometer reads 600 mm at a certain elevation (above sea level). Determine the ...

Q: A tension bar 7 m long is nade up of two parts, 4 m of its length has across section area of 12 cm2 ...

Q: *2-12. The component of force F acting along line aa is required to be 30 lb. Determine the magnitud...

A: Using the concept of resolution of vectors the components along the directions of a-a and B-B can be...

Q: A polymer cylinder (2) is clamped between rigid heads by two steel bolts (1). The steel [E = 29,000 ...

A: For the given polymer cylinder

Q: Q2-A-Three masses are placed on the x-axis :100g at x=0 ;200g at x=20cm ;and 400g at x=70cm. Determi...

Q: 2= 1 m n3= 7 m 4= 12 m Oil h1 Water h2 Mercury h3

A: Specific Gravity of Oil = 0.8 Specific Gravity of water = 1 Specific Gravity of Mercury = 13.6

Q: Classify the following fine grained soil as per IS soil classification system. Liquid limit = 90%, P...

Q: SITUATION: An open cylindrical vessel 1.3 m in diameter and 2.1 m high is 2/3 full of water. If rota...

Q: Draw the shear and moment diagram. Then answer the questions: (1) What is the maximum shear? (2) W...

A: To Determine The maximum shear? The maximum moment?

Q: For the beam shown, the magnitude of the distributed load is wo = 11.2 kN/m and the beam length is L...

A: Using equilibrium equations to calculate the reactions and equations of Shear and bending moment.

Q: TUATION: Water flows through an almost level rectangular channel 3 m wide at 12 m^3/sec. ne depth of...

Q: A solid 2.1 in. diameter shaft is used to synchronize multiple mechanisms in a manufacturing plant. ...

Q: load

Q: A bar AE is in equilibrium under the action of the five forces shown. Determine P (kN). F1 = 85 kN F...

Q: I am doing road accident analysis survey. Could you please suggest me what are the best websites to ...

A: for doing this you can go with some research paper ( case study) and road safety institution of vari...

Q: A WET OF SOIL SAMPLE HAS A VVOLUME OF 4.85 x 10^-4 m3 AND WEIGHS 8.5N. AFTER OVEN DRYING, THE WEIGHT...

Q: A solid 40 mm diameter shaft is subjected to the torques shown. The bearings shown allow the shaft t...

Q: 2. The lap joint that is 130 mm wide and 25 mm thick is connected by three 20-mm-diameter rivets. As...

A: Given, d=20 mm Number of rivet n=3 Allowable shear stress = 65 MPa Bearing stress =45 MPa Maximum te...

Q: A tapered member that is 60 inches in length is fixed connected at both ends C and D. The system is ...

Q: 2. The 55-kg crate shown in the figure rests on a horizontal surface for which the coefficient of ki...

Q: *2-12. The component of force F acting along line aa is required to be 30 lb. Determine the magnitud...

Q: Determine the reaction/s at supports A and D if P1 = 28 lb, P2 = 98 Ib and x = 13 ft. What is the va...

Q: The solid 1.55-in.-diameter rod is subjected to a uniform axial distributed loading along its length...

Q: Soil particle whose size is greater than 300 mm. Rock O boulder cobbles stone

Q: A shaft subjected to torsion experiences a pure shear stress on the surface. The maximum principal s...

Q: The sanding-drum mandrel shown in the figure is made for use with a hand drill. The mandrel is made ...

Q: A soil sample has the following properties: Sp.gr. 2.67, Void ratio = 0.54, Water content = 11.2%. C...

Q: Given the clevis shown, P=D25KN. If the shearing stress is limited to 60 MPa, what is the diameter o...

Q: A laboratory consolidation test on the normally consolidated clay gave the following values: Pressur...

Q: Find the moment (N-m) about point O. Each square is 1 m. on each side. F1 = 58 N F2 = 215 N C1 = 202...

A: To find moment about point O

Q: Use the graphical method to construct the shear-force and bending-moment diagrams for the beam shown...

Q: The soil profile at a site for a proposed office building consists of a layer of fine sand 10.4 m th...

Q: A cantilevered portico slab is 5 m in width and is having 2 m effective span. Assuming moderate envi...

A: In order to restrict the value of deflections the code has prescribed limiting values of Span to dep...

Q: A sample of saturated clay had a volume of 97 cm3 and a mass of 0.202 kg. When completely dried the ...

A: Shrinkage limt is :SL=MC-V1-V2Wdryρw

Q: A bronze pipe (1) is to be connected to an aluminum alloy pipe (2) at flange B. When put in place, h...

Q: A solid circular bronze [G = 6,500 ksi] shaft, 6.0 ft long and 1.325 in. in diameter, carries a torq...

Q: Problem 1. A particle's curvilinear motion is represented by the equation s(t)=20t + 4t - 3t. What i...

A: To Determine Initial velocity

Q: A 300 mm diameter test well penetrates 27 m below the static water table. After 24 hours of pumping ...

Q: A 6 lane highway (3 lanes in each direction) has 11 ft wide lanes, 8 ft wide shoulders, 50 degree ce...

A: Given, Design speed = 60 mph Central deflection = 65o

Q: Determine the reactions for the cable in figure below and the sag (v) at the 60-kip load. 4 ft y 12 ...

A: Given -

Q: a

Concept explainers

Cables

Cables are collections of wires, alternatively referred to as a cord, connector, or plug. They are one or more wires covered in a plastic covering that allows for the transmission of power or data between devices. The earliest use of recognizable electrical cable was the early commercialized telegraph lines. These were iron-made and tedious to produce and install cabling.

Question

A cylinder buoy is 1.2 m in diameter and 2m
high weighing 800N was being held stable
by a cable connected to a 0.5 m3 anchor
block weighing 24kN in air. The cylinder
floats in seawater with a draft of 0.3m.
Specific gravity of seawater is 1.03.
What is the bouyant force on the
cylinder(kN)?
Determine the tension in the cable if the
top of the cylinder is 0.6 m above the water
surface(kN).
Find the rise of the seawater to move the
block from the seabed(m).

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A load W is to be lifted using the crane which is hinged at B as shown in the figure. The value of x1 is 10m, x2 is 8m and h is 18m. Neglecting the weight of the crane. Determine the following. 1. Force at cable AC. 2. Resultant reaction at B. 3. Largest load that can be lifted if the maximum force of cable AC is 50kN.
The 100-lb boy at A is suspended from the cable that passes over the quarter circular cliff rock. Determine if it is possible for the 185-lb woman to hoist him up; and if this is possible, what smallest force must she exert on the horizontal cable? The coefficient of static friction between the cable and the rock is μs = 0.2, and between the shoes of the woman and the ground μ's = 0.8.
Calculate the tension T in the cable which supports the 1000-lb load with the pulley arrangement shown. Each pulley is free to rotate about its bearing, and the weights of all parts are small compared with the load. Find the magnitude of the total force on the bearing of pulley C. (Hint: The radius r does NOT influence the results, because it will be canceled out eventually).
ENGINEERING MECHANICS (No lng explanation needed. Write the complet solutions and legibly. Rate will be given) Determine the maximum mass (kg) that can be lifted at E if the 8-HP motor A has a maximum rotation speed of 300 rpm where the diameter of the shaft AB and CE are 10 mm and 15 mm, respectively The allowable shearing stress is 1 GPa with F.S. of 1.2 for both shafts. Neglect the deformation of the cable at E. Where: Radius of the gear at B, rB = 100mm Radius of the gear at C, rC = 150mm
Determine support reaction. Given a=5 m b=10 m P=30 KN
The 1200-kg car is being lowered slowly onto the dock using the hoist A and winch C. Determine the forces in cables BA and BC for the position shown.
A cable is suspended between two supports at the same elevation 300m high and 500 m apart. The load is 600 kg per horizontal meter including the weight of the cable. The sag of the cable is 50 m. calculate the maximum Tension in the support. a.) 1766.080 KN b.) None of the above c.) 1767.008 KN d.)1765.800 KN e.) 1768.000 KN
A uniform 50-kgf board rests on rough supports located at A and B in the figure. Thefriction coefficient μs=0.60 on both contact surfaces. If a man weighing 80 kgfpulls on the rope with a force of 40 kgf, determine:a) The angles "min" minimum and "max" maximum for which the system is in equilibrium.b) The minimum coefficient of friction that must exist between the soles of the man's shoes andthe soil for each of the cases in section a.
We have a table that we seek to lift with a pulley. The table is uniform, with a weight of 73 Newtons, it is suspended by means of a cable 2.7 meters long, which is attached to the sides of the table and passes through a small pulley located at O. Determine the tension of the cable if: d1=0.43 m d2= 1.14 m
A crane boom of mass 450 kg with its centerof mass at C is stabilized by two cables AQ and BQ(Ae = 304 mm2 for each cable) as shown in the figure.A load P 5 20 kN is supported at point D. The craneboom lies in the y-z plane.(a) Find the tension forces in each cable: TAQ and TBQ(kN). Neglect the mass of the cables, but includethe mass of the boom in addition to load P.(b) Find the average stress (σ) in each cable.
The suspended girder shown is supported by a series of hangers uniformly spaced along a parabolic cable 1. Determine the tension at the midspan. a. 450 kN b. 360 kN c. 400 kN d. 380 kN 2. Find the vertical reaction at A. a. 200 kN b. 220 kN c. 180 kN d. 160 kN 3. If T = 300, find the resulting sag ‘’y’’. a. 3.5 m b. 3.8 m c. 4.5 m d. 4.3 m
A pulley-and-cable assembly supports block W and requires a downward force at P for equilibrium. Knowing that the tension of cable FG is 61.2 N, calculate the mass of the block and the magnitude of the downward force P.