What is the full form for NEHRP? Describe about it.

Q: provided figures A) a. u + v c.u - v b. u + v + w d. u - w B) b. u - v + w a. u - v c. 2u - v d. u +…

A:

Q: hat does C sub c refer to?

A: CC = Coefficient of compression  Which is the ratio of change of void ration before and after…

Q: Which of the following is the largest scale? O 1cm:1mile O 1 mm:10m O. 1:1000 1cm:1km

A: to check largest or smallest scale firstly convert all numerator and denominator in same unit of all…

Q: Q1: Discuss in detail Kennedy and Lacey Theory? Write down all the design steps. Civil Engineering…

A:

Q: Define Weight-Volume Relationships

A: The weight volume relationship is depicted in following properties:- Void ratio:- The ratio of…

Q: 1-3. Represent each of the following quantities in the correct SI form using an appropriate prefix:…

A:

Q: 4. What is the area (in mm2) of a 000 AWG wire? 5. What is the gauge number of a wire with a…

A:

Q: Where do we get n from and what does it stand for ?

A: Problem  How to get value of n, and what does it stand for?

Q: Represent each of the following as a number between 0.1 and 1000 using an appropriate prefix: (a) 45…

A: Unit conversion is very important in field of engineer

Q: 750 lb 3 ft 3 ft 2 ft B 30 Ng (b) Determine the Values of Ax, Ay and Nb Ax is Ib. (nearest whole…

A:

Q: b) R c) la d) L e) F

A:

Q: What is the general range of L/G ratios?

A: L/G ratio stand for the liquid to gas ratio. which is the ratio of the waste slurry to the flue gas…

Q: год I KLF Мmax = Am max=

A:

Q: where did you get 6?

A: 6 is the loading intensity at B.

Q: W= 3+ lb/ft 3 lb/ft A a ft'

A: calculation for resultant force are for location for resultant from o assume x' distance from o…

Q: Represent each of the following as a number between 0.1 and 1000 using an appropriate prefix: (a)…

A:

Q: Kindly give me all right solutions with clear calculations.  *xbar (location of the centroid along…

A:

Q: some examples of the term OFFSET

A:

Q: [CODE G] KN/m [CODE H] KN [CODE G] KN/m ICODE J) m [CODE JI,m [CODE H] KN [CODE I) m (CODE I] m…

A: To maintain equilibrium, the sum of vertical force acting on the beam is equal to zero,  ∈V = 0…

Q: Why is there two values of 1.5? Where did the other one came from?

A: Given :- a solution  To find :- why  two 1.5 m is used

Q: Discuss the following topics and make two illustrative problems of each a. Centroid of volume.

A: In The above problem, we have to discuss the centroid of volume. we have given the formula used in…

Q: Explain the concept of "float."

A: Answer IntroductionThe float generally used for finding the critical path in the project management…

Q: Mathematical problems useful for engineering works are is

A: For plural we should use 'are'. For singular we should use 'is'.

Q: Part B: (define (tail x) ..-) to obtain tail element of list x Examples > (tail '(a)) > (tail '(a…

A: According to given question. Tail x is defined as the trail element of list x. It means that if…

Q: What do you mean by? AEW , sMTI

A: AEW :- Airborne Early Warning An airborne early warning is defined as a system in an airborne radar…

Q: Weir formulas in a.) SI UNITS b.) ENGLISH UNITS

A:

Q: Refer to the figure. bw

A: (a) using 28mm diameter main reinforcement bars, determine    the nominal ultimate moment capacity…

Q: What is the unit of NPSH? КРа

A: To find : Si unit of NPSH.

Q: 3/1 1/2 W% ↓t Wo t Wo-

A:

Q: Differentiate Professional Engineering Cost to Construction Cost

A: Construction: - It is a term which is defined as the process in which build something.

Q: 1-6. Represent each of the following to three significant figures and express each answer in SI…

A:

Q: P. P 3 H. Cross-sectional dimensions.

A:

Q: What is a boundary value problem? Where did it occur?

A:

Q: Show that [Ya,max] [Ya,max = Ya,min][ етах — е Ya – Ya,min Dr етах — еmin Ya

A:

Q: What do you mean by allowances and tolerances in specifications?

A: Tolerance and allowance are two important terms which are used in specifying the dimensions of any…

Q: Determine the magnitude of R (Unit: Ib)

A:

Q: What is the definition of pi?

A: To find:-  the definition of pi

Q: Provide definition of watste and its types with examples

A: Asked to provide definition of waste and its examples.

Q: Common problems in road construction

A:

Q: Question Bank – Forces Evaluate each of the following and express with SI units having an…

A: To find:- Evaluate each of the following and express with Sl units having an appropriate prefix:

Q: L = 3 ft A = 0.2 in.2 L = 2 ft A = 0.4 in.2 A В 10 ft

A: Given: Length of the bar AB = 10 ft Length of shorter rod, L1=2 ft Area of cross-section of shorter…

Q: difference between volume measurements and capacities?

A: solution                                   volume                                       capacity…

Q: your

A:

Q: [A] E [A] [B] [C] ..

A:

Q: What of the following about the scale is/are true ? O a. A scale drawing is a diagram of an object…

A: Option : (e) All of the statements

Q: A B

A: solution solution HGL stands for hydraulic gradient line EGL stands for energy gradient line HGL is…

Q: What sieve size has the lowest percent passing? (2 decimal places, no need for unit

A: Percent passing decreases as we move down the sieve ( smallest sieve at bottom). Since smaller sieve…

Team Management

To complete a specific task or to accomplish organizational goals along with increasing work productivity, individuals need to come together and think along a common path and direction. There are certain tasks in an organization that cannot be done alone and the involvement of more individuals is essential. These groups of individuals who work together for a common goal compose a team and the individual members involved are known as team members.