What is the rate of heat transfer, temperature gradient, and the direction of the heat transfer through a piece of Celotex 3 ft by 8 ft by 1 in. in thickness, if the temp of one surface is 80°F and of the other side is 60°F? - thermal conductivity of Celotex in AES = 0.028.

What is the rate of heat transfer, temperature gradient, and the direction of the heat transfer through a piece of Celotex 3 ft by 8 ft by 1 in. in thickness, if the temp of one surface is 80°F and of the other side is 60°F? - thermal conductivity of Celotex in AES = 0.028.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter1: Basic Modes Of Heat Transfer

Section: Chapter Questions

Problem 1.2P: 1.2 The weight of the insulation in a spacecraft may be more important than the space required. Show...

See similar textbooks

Related questions

Q: Force A =? T

Q: the open tank in the figure contains water and is being filled through section 1. Assume…

Q: When does resonance takes place in a system?

A: Given Data- In Vibration when resonance will occur we have to explain it.

Q: Question No.14: Following data related to reciprocating steam engine as shown in fig. When the crank…

Q: A 3-kg sphere moves in the x-y plane and has the velocity shown at this instant. What is the a.…

Q: The 25-lb block is attached to two springs having a stiffness of k = 14 lb/ft. A periodic force F =…

A: Given data Weight of block = 25 lb Stiffness constant = 14 lb/ft Find the maximum speed .

Q: A —12M 12m The resultant is, O-1200 kN.m 1100 N/m. -1200KN 600KN -12000KN B

A: Given data w = 100 kN Find the resultant force

Q: Q4. The triangular plate ABC is deformed into the shape shown by the dashed lines. If at A, EAB =…

Q: The 100-kg spool is resting on the inclined surface for which the coefficient of kinetic friction is…

A: Write the given data. μk=0.13kG=0.22 mm=100 kgt=7 s

Q: THERMODYNAMICS UPVOTE WILL BE GIVEN. PLEASE WRITE THE COMPLETE SOLUTIONS. NO LONG EXPLANATION…

Q: There are cooled 4 lb/min of oxygen at constant volume from 200 psia and 2400° R to 800° R For…

Q: Steam enters a turbine 80 lb of steam per minute with an enthalpy of 2171 BTU/lb and velocity of 125…

Q: voice that the order of the elements of the matrixdeterminant is important; switching rows 2 and 3…

A: Given data :- Force = (130i - 155j +70k) N Dimensions are x1=1.35 m…

Q: The wheel is attached to the spring. The mass of the wheel is m=20 kg. The radius of the wheel is…

A: Write the given data. m=20 kgr=0.6 mkG=0.4 mL0=1 mk=2 N/mθ=30°L2=4 m

Q: Calculate the work required to stretch the following springs 0.5 m from their equilibrium positions.…

A: Given:Stretch in the spring, x=0.5 ma. Force, F=50 NStretch, x1=0.1 mb. Work, W=40 JStretch, x2=0.4…

Q: Calculate the pressure at A in kPaa.

A: To find pressure at point A

Q: an engine having a 40 hp rating is used as an engine hoist to lift a certain weight at a height of 8…

A: Introduction In this problem, we will calculate the maximum weight that can be lifted by the crane…

Q: stresses for plane stress systems as shown below, (a) Using analytical method, (b) using Mohr's…

Q: A C-130 pilot desires to fly a low-level navigation mission at 4 n miles/ min (240 kn ground speed).…

A: Given Data The ground speed is: Gs=240 kn The wind speed is: Ws=20 kn Altitude is: h=10,000 ft The…

Q: Determine the force in each member of the loaded truss. The force is positive if in tension,…

A: Given data as per the question Weight =260 kg

Q: What does it mean when the compressibility factor, Z, rises above a value of 1 in the graph shown on…

A: Introduction Compressibility of gas (Z) is the ratio of the volume of a gas at a particular…

Q: Bernoulli. A horizontal water jet issues into the atmosphere from a flow in a pipe at Pg= 0.7 atm,…

Q: Refrigerant 134a enters an insulated diffuser as a saturated vapor at 100°F with a velocity of 1200…

A: GivenRefregerent R-134aT1=100oF=(100°F − 32) × 5/9 = 37.778°C saturataed vaporV1=1200 ft/s…

Q: Period: Method of Joints For the truss section below, determine the x and y components and the load…

Q: The pressure, dry bulb temperature and relative humidity of air in a room are 1 bar, 30°C and 70%,…

Q: For steady, fully developed flow inside a straight pipe of diameter D, neglecting gravity effects,…

A: Given data:diameter of the pipe is 'D'Pressure drop is ∆PLength of the pipe is 'L'The wall shear…

Q: Determine the time needed for the load at "B" to attain a speed of 15 m/s, starting from rest, if…

Q: A homogeneous, 4-ft-wide, 5.6-ft-long rectangular gate weighing 800 lb is held in place by a…

Q: Determine whether the four-bar mechanism is a Crank-Rocker, Rocker-Rocker, Crank-Crank, or…

A: The shortest link in the mechanism is The longest link in the mechanism is The length of the other…

Q: Can you re-derive the adiabatic equation of state Vf /Vi = (Ti / Tf) ^(Cv/nR), from ∂V/∂T)s = Cv/P

A: Given Data: dVdTs=CvP Process is adiabatic.

Q: Determine the magnitude P of the vertical force required to lift the wheelbarrow free of the ground…

Q: Oil (SG=0.91) enters the thrust bearing at 250 N/hr and exits radially through the narrow clearance…

A: Given ; inlet diameter, D1 = 3 mm = 0.003 m length of exit pipe, D = 10 cm = 0.1 m narrow…

Q: 1. Please solve dy/dx=y/x +sin (y/x) 2. Xdy/dx+y²/x=y Solve both

Q: What is the smallest acceleration that bar A needs to move horizontally to maintain bodies 1 and 2…

Q: - Rz (Ten-point surface roughness, The mean and valleys of distance b/us five Over a Wavines: ·Lay:…

Q: Determine the force P required to maintain the 230-kg engine in the position for which 0 = 27°. The…

Q: Given the following information for two windows in a room, one placed on the south side, and the…

Q: How long will it take the water surface in the tank shown to drop from h = 3 m to h = 50 cm?

A: Answer 5.79: Given data: h=3 m to h=50 cmV=2gh Need to determine the time taken by the water surface…

Q: 3.11e If the deformation mapping of a body in a naval machine is given by x(X) = (X + AXz)ên + (Xz+…

Q: What are the different Heat pump circuits? Explain any one of them with the help of neat sketch

A: given; three types of different circuit for heat pump. air to air water source geothermal

Q: free endpoint B (Figure 2) The force is given by F-110 NI-145 NJ+70 Nk The dimensions are 1.25 m.…

Q: An oil pump operating at steady state delivers oil at a rate of 10 lb/s through a 1-in.-diameter…

Q: What is an adverse pressure gradient, and where does it occur on an airfoil (Show that on an airfoil…

A: An airfoil is defined as a streamline that is capable of generating significantly more lift than…

Q: Question 3: The free body diagram of the back model in static equilibrium is shown in Figure 1…

Q: A rigid, perfectly insulated system contains 0.53m3 of helium at 1000 kPa. The system receives 1000…

A: Since the container is rigid, the volume of the helium remains the same. Also, the adiabatic index…

Q: The 23-kg disk, is pinned at its mass center O and supports the 3-kg block A. The belt which passes…

Q: The motion of the collar at "A" is controlled by a motor at "B" such that when the collar is at SA =…

Q: Calculate the forces in members AB, BH, and BG. Members BF and CG are cables which can support…

Q: Two adiabatic chambers, 2 m³ each, are interconnected by a valve, as shown in the figure, with one…

A: Given data: V1=2 m3P1=1200 kPaTA=127°C=400 K Need to determine the change in internal energy and…

Q: A metal hollow shaft is subject to a tensile load of 53kN and a positive torsional moment (right…

A: Given Data: Tensile load acting on the shaft FT=53 kN=53×103 N. The torque acting on the shaft…

Question

- thermal conductivity of Celotex in AES = 0.028.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Follow-up Questions

Read through expert solutions to related follow-up questions below.

Follow-up Question

what is the temp gradient and direction?

Solution

by Bartleby Expert

SEE SOLUTION

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

1.3 A furnace wall is to be constructed of brick having standard dimensions of Two kinds of material are available. One has a maximum usable temperature of 1040°C and a thermal conductivity of 1.7 W/(m K), and the other has a maximum temperature limit of 870°C and a thermal conductivity of 0.85 W/(m K). The bricks have the same cost and are laid in any manner, but we wish to design the most economical wall for a furnace with a temperature of 1040°C on the hot side and 200°C on the cold side. If the maximum amount of heat transfer permissible is 950 , determine the most economical arrangement using the available bricks.
1.2 The weight of the insulation in a spacecraft may be more important than the space required. Show analytically that the lightest insulation for a plane wall with a specified thermal resistance is the insulation that has the smallest product of density times thermal conductivity.
What is the rate of heat transfer through a piece of Celotex 3 ft by 8 ft by 1 in. in thickness, if the temp of one surface is 80°F and of the other side is 60°F? thermal conductivity of Celotex in AES = 0.028. Pls determine the temperature gradient and the direction of the heat transfer as well.
Q2: A: The exterior wall of a single-story office building near Chicago is 3 m high and 15 m long. The wall consists of 100-mm face brick, 40-mm polystyrene insulating board. 150-mm lightweight concrete block, and an interior 16-mm gypsum. The wall contains three single-glass of 3 mm thickness windows 1.5 m high by 2 m long. Calculate the heat loss through the wall at design conditions if the inside temperature is (20 °C). The outside temperature is (-18 "C).
Define the thermal conductivities of some materials at room conditions
A 1 in. o.d. (outer diameter) tube reactor is insulated with a 3 inch layer of asbestos. If the temperature of the outer surface of the insulation is 100 °F and the rate of heat loss per foot of reactor length is 50 BTU/hr, what must the temperature of the inside of the reactor be? [for asbestos, k = 0.105 BTU/hr ft °F]
(a) The temperature at the surface of the heating rod, T1. (b) If the salt solution temperature is 300 degree Celcius, what is the value of convection heat transfer coefficient, h of the salt solution ? (c) If the heating rod is not covered by metallic cylinder and corresponds to the result of part (a) and (b), how much the rate of energy transfer to the salt solution ? (d) Compare and discuss the difference of heat transfer with and without the matallic cylinder.
Required info: There is a 2.00 cm thick stagnant air pocket. a) What thickness of cork would have the same R-factor as the stagnant air pocket? The thermal conductivity of air is 0.0230 W/m-K and of cork is 0.0460 W/m-K. b) What thickness of tin would be required for the same R-factor as a 2.00-cm-thick stagnant air pocket? The thermal conductivity of air is 0.0230 W/m:K and of tin is 66.8 W/m-K. THANK U
Is the material homogeneous and isotropic? How does it behave?
The temperature in deep space is close to absolute zero, which presents thermal challenges for the astronauts who do space walks. Propose a design for the clothing of the astronauts that will be most suitable for the thermal environment in space. Defend the selections in your design.
The 12ft x 14 foot room illustration in figure 1.6a has an exterior wall at a surface temperature of 60°F, a window surface temperature of 40°F (double glazing on a cold day). The two interior wall surfaces are a temperature of 72°F. Determine the MRT sensation of a person standing in the center of the room. (See figure 1.6 below) Round your values to the nearsest hundreth decimal place (0.00). You will need to upload your mathematical work in question 4.
The compartment below is used as a freezer of refrigerator compartment. Inner wall is at -10 C and outer wall is at 20 C. Insulator with a thermal conductivity of 0.040 W/(mK) is used to prevent the heat losses from the compartment. The shape is in square form with a side of 1.3 m and unit width into the page. Determine the amount of the heat load if the thickness of the insulator is 2 cm? *