What is the shearing strength of soil along a horizontal plane at a depth of 4 m in a deposit of sand having the following properties Angle of internal friction, = 35° Dry unit weight, d = 17kN/m³ Specific gravity, Gg = 2.7. Assume the ground water table is at a depth of 2.5 m from the ground surface. Also find the change in shear strength when the water table rises to the ground surface.

What is the shearing strength of soil along a horizontal plane at a depth of 4 m in a deposit of sand having the following properties Angle of internal friction, = 35° Dry unit weight, d = 17kN/m³ Specific gravity, Gg = 2.7. Assume the ground water table is at a depth of 2.5 m from the ground surface. Also find the change in shear strength when the water table rises to the ground surface.

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter9: Consolidation

Section: Chapter Questions

Problem 9.20CTP

See similar textbooks

Similar questions

If the internal friction angle of a backfill soil is equal to 28°. Calculate the Rankine active pressure coefficient.
A rectangular footing (4.5 x 4.36 m.) is placed 1.98 m. below the ground surface. The soil arrangement is composed of sand (ground) for the first 6.94 meters and followed by clay for the next 6.78 meters. The force acting on the footing is 10,700 kN. Determine the settlement of the consolidating layer in mm. Assume a 2V:1H pressure diagram. Unit weight of sand = 16.9 kN/m3. Clay has the following properties: Unit weight = 18.3 kN/m3, Void ratio = 95, Liquid limit = 49. Round off to two decimal places.
A deposit of sand has the following properties: angle of internal friction, Ф = 35°, Dry unit weight, Ɣd = 1.7 gm/cc (17 kN/m²), Specific gravity, G = 2.7. Assume the ground water table is at a depth of 2.5 meters from the ground level. 1. What is the shearing strength of soil along a horizontal plane at a depth of 4 m. a. 41 kN/m² b. 11 kN/m² c. 58 kN/m² d. 15 kN/m² 2. Find the change in shear strength, when the water table rises up to the ground level. a. 41 kN/m² b. 11 kN/m² c. 58 kN/m² d. 15 kN/m²
If the internal friction angle of a backfill soil is equal to 28°. Calculate the Rankine active earth pressure coefficient.
A granular soil is subjected to a minor principal stress of 200 kN/m2. If the angle of internal friction is 30°, determine the inclination of the plane of failure with respect to the direction of the major principal stress. Show free body diagram. a.30 b.45 c.60 d.37.5
question 5 A rectangular footing (4.67 x 4.45 m.) is placed 1.62 m. below the ground surface. The soil arrangement is composed of sand (ground) for the first 6.22 meters and followed by clay for the next 5.85 meters. The force acting on the footing is 10,929 kN. Determine the settlement of the consolidating layer in mm. Assume a 2V:1H pressure diagram. Unit weight of sand = 16.6 kN/m3. Clay has the following properties: Unit weight = 18.6 kN/m3, Void ratio = 28, Liquid limit = 43. Round off to two decimal places.
Plz give the correct answer. Compute the intensities of active and passive earth pressure at depth of 8 m in dry cohesionless sand with an angle of internal friction of 30 degrees , and unit weight of 18kN / (m ^ 3) What will be the intensities of active and passive pressure if the water level rises to the level? Take the saturated unit weight of sand as 22kN / (m ^ 3) .
6. From the given soil profile, the groundwater table is located 2m below the ground level. (See picture below) Compute the horizontal effective stress at point A. (Answer: 53.36 kPa) Compute the lateral effective stress at point A if the lateral earth pressure coefficient at rest is K0=0.50. (Answer: 26.68 kPa) Compute the lateral total stress at point A. (Answer: 56.11 m)
A soil profile is shown in Figure Q3(b)(i). The groundwater level is located on the ground surface. The sand layer is under artesian pressure where the excess pore water pressure is 40 kN/m^2. (i) Calculate the total vertical stress, pore water pressure and effective vertical stress at the base of each layer. (ii)Determine the increment of the effective stress at the base of sand layer if the 1.5m height fill will be imposed on the ground surface. Note that, the density of the fill material is 1750 kg/m^3. (iii) The excavation will be made in the clay layer for the basement construction. Evaluate the stability of the soil from boiling or quick condition. The depth of the excavation is shown in Figure Q3(b)(ii). (iv)Propose the maximum depth of cut that can be made to avoid boiling or quick condition.
The soil in a deposit underlying an area where a level ground surface exists has a unit weight of 22 kN/m3. Determine the principal stresses o1 and oz at a depth of 5 m below the soil surface if the lateral pressure is 0.50 of the vertical pressure. Adjust your answer to ZERO decimal places. 01 = kN/m2, 03 = kN/m2
Refer to the soil profile shown. Given H1 = 9.76m and H2 = 4.22 m. If the ground water table rises by 2.41 meters, determine the change in effective stress (numerical value only, in kPa) at the bottom of the clay layer. Properties of dry sand: Gs = 2.56, e =0.61. Properties of clay: Gs = 2.79, e = 0.83.
A soil profile consists of; layer 1, 10m sand layer and layer 2, 3m clay layer. The ground water table is located 4m below ground surface. For sand, γdry=2.00 T/m2 (tons/m2), γsat=2.25 T/m2, and for clay layer, LL=46%, water content=42% and Gs=2.76. A uniform vertical stress, ΔP=20T/m2 is applied at the ground surface. Determine, a) Effective unit weight of clay, b) overburden pressure at the mid point of the clay layer, c) primary consolidation settlement