What is the solution to this question Q ) A 440V d.c. compound generator has an armature, series field andshunt field resistance of 0. 5Ω, 0.1Ω, and 200Ω respectively.Calculate the generated e.m.f and electromagnetic power(developedpower) in armature while delivering 40A to external circuit for both1-Long compound connection2-Short compound connection

What is the solution to this question Q ) A 440V d.c. compound generator has an armature, series field andshunt field resistance of 0. 5Ω, 0.1Ω, and 200Ω respectively.Calculate the generated e.m.f and electromagnetic power(developedpower) in armature while delivering 40A to external circuit for both1-Long compound connection2-Short compound connection

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.53P

See similar textbooks

Similar questions

Electric Machine-check image, all question there. Consider the above equivalent circuit of IM. A three phase, Y connected , 215 V (line to line), 7.5Kw , 60Hz , three pole IM has the following parameter values in Ω/phase referred to the stator R1=0.294Ω , R2=0.144 Ω, X1=0.203 Ω, X2=0.409 Ω, Xm=10.25 Ω The total friction , windage and core losses may be assumed to be constant at 350W independent of load, For a slip s=0.02, compute the followings a)Stator current b)Power factor(pf) c)Rotor speed d)Power Output(shaft) e)Output(shaft) torque f)Efficiency
A 100 kN, 500 V, 300 rpm generator has the main dimensions, D = 1.5 m, L= 0.4 m, flux density in the air gap = 1 Wb/m voltage drop at full load is 7 volts and form factor k,= 0.7. Calculate (1) Emt/ conductor (ii) Number of conductors in series (ii) Total flux.
EE 422 - AC and DC Machinery Solve the following problems completely. Box and Round-off your final answer in nearesttwo decimal places. 1.A long shunt compound generator delivers 100A,250V at rated load. The resistances of the various windings are: Ra = 0.1 ohm, Rip = 0.02 ohm, Rsh = 100 ohm and Rse = 0.025 ohm. If the stray power losses amount to 1.8kW, solve for the overall efficiency of the generator. answer: 86.36% 2. A motor is supplying 60 Nm of torque to its load. If the motor’s shaft is turning at 1,800 rpm, what is mechanical power to the load in horsepower? answer:15.2 hp
A 125-volt d-c generator whose internal resistance is 0.15 ohm is connected through a 0.45 ohm line resistor to charge two 90-volts storage batteries A and B in parallel. If the internal resistance of batteries A and B, respectively, 0.32 ohm and 0.4 ohm, what are the charging currents?
• T or F, modify the wrong part if False, please underline twice your answer if True or False. At maximum efficiency, the amount power that a DC generator would deliver will always be at maximum.
A hydro-electrie station is operated with a mean head (h) of 30 m and consume (discharge water) 218.75 * 10 6 m3 of water in one ycar for the average load. The expected load factor for the station is 80 %. Calculate the power in Kw for which the station should be designed (max.load). Assume that the mechanical efficiency of the turbine is 90% and the efficiency of the generator is 95%,
Two shunt generators and a battery are working in parallel. The open circuitvoltage, armature and field resistances of generators are 250 V, 0.24 ohm, 100ohms and 248V, 0.12 ohm and 100 ohms respectively. If the generators supply thesame current when the load on the bus-bars is 40 A. Calculate the e.m.f. of thebattery if its internal resistance is 0.172 ohm.(Ans. 248
Problem 7. There is a triphasic line. The line will have a length of 100 km. The drivers are bluejay. 1. Calculate the percentage increase in AC resistance at 50°C, due to the skin effect. 2. Calculate the equivalent resistance of the line, considering an operating temperature of 70°C
- Loads, Service, and Overcurrent Protection 6.a. The general lighting load is based on a _______ per square foot basis.A. kilowattB. number of circuitsC. volt-ampereD. general illumination6.b. What's the primary disadvantage of using copper conductors?A. AvailabilityB. WeightC. CostD. Durability
9.If there is a Line to Ground fault in a network, and it is found that the zero sequence current of a generator is 10<0° A, we can say that A) The current flowing in the generator from neutral to ground is zero. B) The generator has a floating neutral. C) The current flowing in the generator from neutral to ground is 10<0° A. D) The current flowing in the generator from neutral to ground is 30<0° A. E) N. A.
Electric Machine; Check image, all question there. Let’s consider three phase, Y connected, 220 volt (line to line), 7.5 kW, 55 Hz, four pole IM has the following parameter values in Ω/phase referred to the stator: R1=0.294Ω , R2=0.144 Ω, X1=0.503 Ω, X2=0.209 Ω, Xm=13.25 Ω Determine the following for 0.02 slip. a)Electromechanical Torque(Tmech) Electromechanical power(Pmech) b)Maximum electromechanical torque(Tmax),Corresponding speed(nr,max) c)Electromechanical starting torque(Tstart), Corresponding stator load current(I2,start)
Power transmission and distribution in the Philippines Draw and discuss the steps of power transmission and distribution from the power plant to the end-user (include the material used and rated power transmission. Discuss the advantages and disadvantages of single-phase and three-phase system. Discuss the “The War Current” between two inventors Nicolai Tesla and Thomas Edison. Who do you think was the better inventor?