What is the total settlement of the clay layer five years after the completion of primary consolidation settlement?

Q: Q5/ The depth of water before the hydraulic jump is 2.5 m and the velocity is 5 m/sec. Determine the…

A:

Q: 1.) A beam carries the loading shown. Design a rectangular timber beam if the permissible stresses…

A: Permissible bending stress in tension and compression = 120 MPa  Permissible shear stress = 100 MPa…

Q: If a horizontal force of 890 N is developed by the water jet leaving the pipe on the 90° deflector…

A: Solution-The given values are as follows, Horizontal force(F)=890NEfficiency(η)=90%To DetermineThe…

Q: Design a column to support an Mx = 230 kN.m, My =140 kN.m and axial load N = 3500 kN. The column is…

A: Columns are vertically arranged and carry load from beams to footing. Columns are designed based on…

Q: Am 8 kN/m ΒΙΣ 2m Figure 7 C

A:

Q: all steel are Fy = 345 MPa unless noted otherwise W12x19: d = 30.8864 cm bf = 100mm tf = 8.725 mm tw…

A: Hi! Thank you for the question As per the honor code, We’ll answer the Third question since the…

Q: 4 m 500 N/m 30 1.6 kN 4 m B

A:

Q: * Draw M moment diagrams by using both slope deflection method and Cross method separately

A: As per the policy, solution will be provided only for slope deflection method,question for…

Q: 1. Titanium alloy with an elastic modulus of 107 GPa (15.5 x 106 psi) and an initial diameter of 3.8…

A:

Q: Q2/ Water flow in rectangular section at the flow rate of (3 m³/sec ) at width of (1 m), the depth…

A:

Q: 1. Determine the moments at A, B, C and D then draw the moment diagram. Assume the supports at A and…

A:

Q: Q1/ For the truss shown in Fig. (1) Find All reactions All Area of the members = 3 EI Constant note:…

A: Truss A truss is a construction comprised entirely of parts that are held together by two forces. A…

Q: * In a particular road intersection, it has been observed that (2/3) of vehicles turn to the right…

A:

Q: F6-10. Determine the force in members EF, CF. and BC of the truss. State if the members are in…

A: Determine the force in members EF. CF, and BC of the truss.

Q: The face of a vertical dam has the shape of an isosceles trapezoid of altitude 11 ft, upper base 28…

A:

Q: Calculate the weight of a Wire Mesh Reinforcement needed for a 10'x10' slab. The specifications are…

A: Requirement of wire mesh reinforcement in slab Mesh reinforcement is required in a composite slab…

Q: A 1-0m 2| KN 13 Tekw/m 2m मै

A: Beam: The primary structure which resists loads coming onto the structure in a building is known as…

Q: Describe how groundwater is affected by the following terrains: permafrost, desert, and the ocean…

A: Answer Introduction Groundwater is the largest reservoir of liquid fresh water on Earth and is found…

Q: An unsymmetrical triangular weir with a vertex angle equal to a = 38 deg(left half) + B = 31…

A:

Q: 1. Determine the moments at A, B, C and D then draw the moment diagram. Assume the supports at A and…

A:

Q: What can be done if the required development length is restricted by the of constructions? a. Bend…

A: Note- Hi! Thank you for the question, As per the honor code, we are allowed to answer three…

Q: Define the friction losses in pipes, what are the parameters that effect on friction in the pipe?…

A:

Q: Solve the problem indicated below. NEATLY draw the cross section of each beam and all diagrams that…

A:

Q: for the beam Shown in figure, find the value of rotation at supports and the value of deflection at…

A:

Q: Talk about geology, like earthwork, tsunami, based Somalia?

A: Somalia also has some of the world's biggest scattered populations. Outside of Africa, there are…

Q: 11-Determine the greatest angle u so that the ladder does not slip when it supports the 75-kg man in…

A: Slippery condition may occur at the contact either A point or B point , here Assuming Point B for…

Q: A series of pipes with Q=194 L/s was to be examined for head losses. If the roughness coefficient is…

A: To Determine The minimum diameter (mm) of the pipe that could replace all three pipe, (D)

Q: As shown in Fig. 1, a cylinder of diameter 122mm and length 200mm is placed inside a concentric long…

A:

Q: 35. Determine the minimum speed of a car at the point the brakes are immediately applied to avoid a…

A:

Q: Determine the height to be raised of box mars 12.4kg to gain Potential energy ergy of 133 2 J

A:

Q: An oil (S = 0,85, v 1.8-10 m/s) flows through 0.1m diameter pipe at 2m³/sec, 150m long. Find the…

A:

Q: 60 Looking at the x direction, provide the front view, top view, and left-side view using the meter…

A: WE HAVE TO DRAW THE LEET SIDE , FRONT VIEW AND TOP VIEW   Looking at X direction, we conclude that…

Q: what is the central angle in degrees of a simple curve whose radius is 20m and the distance of the…

A:

Q: 1. Determine the moments at A, B, C and D then draw the moment diagram. Assume the supports at A and…

A:

Q: Compute the midspan value of deflection for 900N 600N 3m the beam shown? 3 Ans/ S = 3100 N.m ²³ ΕΙ…

A:

Q: Ex) A (1/5) scale of a vehicle is to be tested, One in a wind tunel, second in a water tunnel,…

A:

Q: Q2: In Fig. 1 the upper plate moves upwards in 1.5 m/s and the lower plate moves upwards in1 m/s,…

A:

Q: A fluid is contained between parallel plates; the bottom plate is fixed and the upper plate moves.…

A: solution Given shear stress ζ=162Padistance between plates dy=2mm=0.002mts velocity du=1.4ms-1

Q: me the reactions at the supports. - 4 m 500 N/m 30 4 m

A:

Q: estimate the quantity of flow

A: Reservoir: - It is defined as a natural or artificial place where water is to be stored for the use…

Q: 5. A child in a school crossing ran into the street and was struck by a car, despite the driver…

A: Skidding occurs when a vehicle's tires lose traction on the road. When your tires lose grip, you…

Q: A rigid bar AB is hinged at A and supported by copper rod 2 m long and steel rod i m long as shown…

A:

Q: What is the importance of shear and bending moment diagra in beams? 8:10

A: Importance of shear and bending diagram: It is the diagram which represents the total load and…

Q: Question 2 Estimate the quantity of Steel Reinforcement from given schedule bar table 4 for the…

A: Assuming that the bars in B1, B2 and B3 are curtailed at 1 m from the supports  Bar Tag Bar…

Q: Determine the amount of water needed to achieved the normal consistency of 650 grams cement by using…

A: The amount of water required to be mixed in cement to make a cement paste such that when the sample…

Q: rectangular barge with 6750 m² horizontal cross-

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: Q1: Determine the volume of earthwork to be excavated for the plot shown in fig 1. The formation…

A: This question belongs to subject estimation & costing . In this question we find out volume of…

Q: Q1: Water flows through a smooth pipe of a 65 mm diameter and a 10 m length with a head loss of 0.5…

A:

Q: 3. Determine the required plastic moment of resistance assuming uniform section of

A: DETERMINATION OF PLASTIC MOMENT CAPACITY OF BEAM SECTION

Q: SITUATION 6 The hull of a boat has a volume of 180 m³, and the total mass of the boat when empty is…

A:

Calculation of Settlement

The vertical displacement of the structural foundation due to the loading from the superstructure is known as settlement. It is due to the reduction of air voids present in the soil. The amount of vertical displacement depends on the bearing capacity of the soil on which the foundation is laid. The effect of the settlement depends on the magnitude of settlement, uniformity, and the structural design of the structure. The maximum allowable settlement for residential and office buildings should be less than 18 mm, for industrial buildings, it is 38 mm and for commercial buildings, it is 25 mm.