what is the value of the current Iin?

Q: 3. R=__. 1=12 mA E 12 V

A:

Q: 4. Calculate the energy dissipated by the circuit in 50 seconds. 10 ohm 100V a) 50kJ b) 50J c) 100j…

A:

Q: Determine the pressure difference between points A and B in kPa. Given Specific Gravities: Benzene…

A: According to the question we have a specfic gravities for the several liquids is given which are,…

Q: Assume that 6.25 x1015 electrons flow past a given point in a conductor every 10 s. Calculate the…

A: Rate of flow of charge is called current I.e. Current = charge/ time.  Charge of the electron…

Q: Determine the total current on a circular wire of radius 2mm and J =500az Am2 25.132 mA 5.137 mA…

A:

Q: A string insulator having 4 units. 33.33% of voltage of the total voltage is across the bottom most…

A: Given  String insulator having Number of insulator discs is n=4Voltage across the bottom unit is…

Q: How much energy must a 4 V flash light battery expend in producing a current flow of 129 mA for 9…

A: Find the energy of the circuit of the voltage and current is given with time 9min

Q: 1=4 mA E=6 V

A:

Q: The resistance of 250 x 103 ft. of copper wire (pno - 10.36 (cmil-A)/ft.) is found to be 25.9 ohm,…

A:

Q: Convert the wye equivalent to its delta equivalent

A:

Q: 12 k2 15 kN 36 V 18 mA 60 kN VAB B

A:

Q: The resistance of a 10 AWG copper wire is 20 ohms at 50 degrees Celsius. Calculate its length.

A:

Q: 30 - If the voltage at the DIAC ends falls below what voltage value, it becomes an insulator? A) 25…

A: 30 ) If the voltage at the DIAC ends falls below what voltage value, it becomes an insulator?

Q: Taking R = 2.80 k2 and E= 430 V in the figure below, R 2R 28 3R determine the direction and…

A:

Q: FIGURE 1 2 mA 6 kN 2 ΚΩ ww 6 kN 8 mA 3 kn 1 kn Vo 12 V(+

A:

Q: show complete solutions please thank u A copper conductor measures 0.60 ohm at 20 degrees…

A: In this question, choose the correct option find the resistance R at the temperature T= 30° if…

Q: Power System, Define the following (i) Spinning Reserve (ii) Hot Reserve

A: In this question we will define spinning reserve and hot reserve....

Q: R,. Si E, Vo

A:

Q: Determine the total charge entering a terminal betweent = 1sandt =2s if the current passing the…

A: Given current is - Time interval is between t = 1 sec and t = 2 sec.

Q: SITUATION NO. 1 - A specific circuit element has a charge of q = 10e^(2t ) coulomb and a voltage…

A:

Q: The current flowing through a device is i(t)= 5sinót A. Calculate the total charge flow through the…

A:

Q: How much energy must a 2 V flash light battery expend in producing a current flow of 183 mA for S O…

A: Electric energy: Electrical energy is energy derived as a result of movement of electrons or charge.…

Q: 33. A string insulator has 4 units. The voltage across the bottom - most unit is 33.33% of the total…

A: In this question we will find string efficiency...

Q: Fill in the blanks: ents Si 4.7 kA +12 Vo Vaz S. GAAS its Vo1= V, 1 decimal te ID(GaAs)= mA (…

A:

Q: Q': The diameter of a copper wire is 2 mm, a steady current of 6.25 A is generated by 8.5x10/m°…

A:

Q: 11. According to Ohm's Law, electron flow is proportional to electrical pressure. a. Inversely b.…

A: Because it's a multiple question so as per Bartleby guidelines we have to do only first part of the…

Q: 0.33 kn V Si ID1 ID2

A:

Q: Current can not flow through an insulator because they have O a. free electrons O b. no free protons…

A: The electrons in the insulator's atoms are strongly bonded, it means they have no free electrons so…

Q: 12 Ω + vi 6Ω iz 10 Q 40 Q 15 V Figure 2(b) + sI

A:

Q: The 12-gauge copper wire in a typical residential building has a cross-sectional area of 3.31x10 -6…

A:

Q: D2.4. Calculate the total charge within each of the indicated volumes: (a)0.1 s |xl. lyl. I=l s0.2:…

A:

Q: 10. Determine power absorbed by each element in the following circuit. T=6 Amp 17 Amp + 12 Volt 8…

A:

Q: SITUATION NO. 1- A specific circuit element has a charge of q = 10e^(2t ) coulomb and a voltage…

A: It is given that: q=10 e2t Cv=10 e-t V

Q: If the thickness, of an insulator is increased then its breakdown voltage 1) remains unchanged 2)…

A: Breakdown voltage: It is defined as the minimum voltage that should be applied to the insulator to…

Q: 12 k 2 k2 20001, 6 V 4 kN )2 mA 4 kN V. Figure 5

A:

Q: Nichrome ribbon resistor elements each has a resistance of 1 ohm. The element is made from sheet of…

A:

Q: Figure shows the voltage across a power semi-conductor device and current through the device during…

A: Solution: According to the question: Energy loss:EL=∫VI.dt=∫02V×60.dt+∫2545I.dt=60∫02V.dt+45∫25I.dt…

Q: 20. The quantity of charge that will be transferred by a current flow of 10 A over 1 hour period is…

A: Given, Current flow, i=10 A Time, t = 1 hour = 3600 sec

Q: How much change in the power of wind will take place if wind velocity becomes 3 times 3 times 27…

A: Wind power will increase 27 times of wind power before

Q: How much energy must a 4 V flash light battery expend in producing a current flow of 186 r for 8…

A: Voltage V = 4v I= 186mA Time t= 8 minutes t= 8*60sec= 480sec

Q: How much energy must a 4 V flash light battery expend in producing a current flow of 116 mA for 8…

A: Right Answer option 222.72 J

Q: Resistance of 800 Q has a conductance of O 125 millisiemens O 1.25 millisiemens O 12.5 millisiemens…

A: The explanation is as follows.

Q: iin 6 mA, power rails are ±12 V, find iout in milliamperes.

A: An amplifier is an electronic circuit used to increase the power of the applied input signal. The…

Q: Which one of the following is a Conventional energy source?  a. Tidal energy b. solar c. Nuclear…

A:

Q: In a string of suspension insulator with three units,the line unit has 12KV and k=0.15. The voltage…

A:

Q: 91 kN 7 k2 V.

A: Operational Amplifier: A direct coupling amplifier that can increase the bandwidth of an input…

Q: 84. What is the equivalent area in square inch for a conductor 336,400 circular mil? a. 0.428 b.…

A: This problem is mainly depends on unit conversions. The relation between mil and inch is given as…

Q: Two cities are 150 km apart. Electric power is sent from one city to another city through copper…

A: Given: Electric power is sent from one city two another city through copper wire Distance between…

Q: If the current is 1.06 mA at an applied voltage of 600 mV, and the current is 4.01 mA at an applied…

A:

Digital Integrated Circuit Design

Digital IC design is a procedural interaction that involves converting determinations and highlights into computerized blocks, which are then further transformed into basic circuits. A significant number of the imperatives related with advanced IC plan come from the foundry cycle and innovative restrictions.