What the differences between from the following: -Natural and refinery gas -Thermal and catalytic reforming

Q: What is the advantage of having high steam quality compare to low steam quality?

A: Steam quality formula  x = mvapormliquid+mvapor

Q: What are the modifications that we can do to improve the performance of gas powe  plant? Explain…

A: To increase the performance of the power plant various modifications are can be added, some of them…

Q: What do you mean by breakthrough curve for fixed-bed adsorption system?

A: Given: breakthrough curve for fixed-bed adsorption system

Q: Explain regeneration by pressure reduction?

A: The regeneration done by the reduction of pressure is known as pressure swing adsorption.

Q: P a Pa P,/2 b 2V.

A: For solution refer below images.

Q: How does the pressure affect the value of latent heat of fusion?

A: Latent heat of fusion is the amount of heat required to change the phase of a substance from solid…

Q: Why should the adiabatic flame temperature be much higher for a pure oxygen feed than for an air…

A: -The temperature of the products of the combustion reaction if no heat is lost in the external…

Q: How is regenerative thermal oxidizer (RTO) different from traditional thermal oxidizer?

A: A thermal oxidizer or a thermal incinerator or afterburner is an air pollution control process unit…

Q: What are the advantages of Contact condensing systems?

A: In contact condensing systems, the direct contact between the two mediums takes place. The…

Q: Calculate the energy wasted (Qexhaust) from convection oven if 5000SCFM natural gas is found in the…

A: Introduction: Designers who need to carry hot fluids through pipes over a long distance must account…

Q: Dehumidifier is an example of which of the following?

A: Dehumidifier is a air conditioning device.

Q: Hello Sir, Good Morning. I have a question in my homework related thermodynamics lesson. The…

A: To propose whether it is adequate to use water instead of refrigerant 134-1 as the working fluid.

Q: In a Brayton cycle air enters the compressor at 101.32 kPa, 32°C and leaves at a pressure of 808…

A: Given dataAir enters the compressor P1 = 101.32kPaTemperature of air at entry of compressor T1 =…

Q: 4. How does the latent heat of water vary with the working pressure? Explain.

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: by a regenerative ditions and in an

A:

Q: Carbon dioxide (R-744) is unlikely to be used as a refrigerant because of its _______.   A) high…

A: Carbon dioxide (R-744) refrigerant has only limited use because of the high power requirements per…

Q: What is energy release rate and the relationship with stress intensity factor?

A:

Q: Differentiate between regenerative system and non-regenerative systems in Adsorption.

A: given: Differentiate between regenerative system and non-regenerative systems in Adsorption.

Q: Analyze the thermal power plant carefully and list all burn out products which are harm full for the…

A: Thermal power plants are known to pump out a lot of greenhouse gases and ash, which are by-products…

Q: 1-why the heat exchanger are produce from stainless-steel? 2-what are the differentiation between…

A: Answer 1: The primary function of the heat exchangers is exchange the heat from hotter fluid to the…

Q: A refrigeration technician had to say ;"Absorption refrigeration systems are cost effective in ice…

A: Refrigeration  Refrigeration is the process of lowering the temperature of the substance.…

Q: The conclusion of Inverse Square Law for Heat

A:

Q: 4-How does the latent heat of water vary with the working pressure? Explain.

A: As pressure on molecule increases they require more heat to overcome the pressure force acting or to…

Q: Describe Isentropic Processes of Ideal Gases

A:

Q: 2. Find the theoretical C.O.P. for a CO2 machine working between the temperature range of 25°C and –…

A:

Q: efficiency and pres Explain each of the processes on the T-s diagram.

A: Given: Gas turbine cycle Describe the processes.

Q: Illustrate, Label and Discuss the following on fuel processes a. Thermal Cracking

A: Fuel process: It is the transformation of the raw fuel material or fluid into a hydrogen-containing…

Q: hat does back work ratio mean and should it be greater than one?

A: In  turbine  air expend and produced work. The part of the the work is being utilized to run the…

Q: room is heated by an iron that is left plugged in. Is this a heat or work injection? Take the entire…

A: It is required to evaluate given statement

Q: Fuel Stack Combustion gases to stack Boiler AirD Turbine Electric generator Condenser Warm water…

A: To find: The technical recommendation for the suggested system.

Q: STAINLESS STEEL AND HOW IT AFFECT ENVIRONMENT OR HUMAN HEALTH

A: Stainless steel is a ferrous alloy produced for making cooking utensils , kitchen accessories etc…

Q: Research: Reheat and Regenerative Cycle - Processes in a Reheat & Regenerative Cycle - Diagrams -…

A:

Q: What is organic Rankine cycle? Describe and classify the fluids used through the T-s diagram.

A:

Q: Write one to two paragraph Executive Summary of a shell and tube heat exchange and the manufacturing…

A: A Heat exchanger is a device which is used to transfer heat from one fluid to another. There are…

Q: A student proposes to use water instead of refrigerant-134a as the working fluid in an air…

A:

Q: Q- Why does the process of steam injection used in applications which need to maintain air with high…

A: In comparison to other humidification methods, steam humidifiers have a negligible effect on…

Q: While discussing the reaction by a refrigerant to heat:

A:

Q: Where do the deposits of burnt products accumulate inside an engine and what are the remedial…

A: Deposits of burnt products accumulate inside an engine can take place in following part and their…

Q: Explain Gas-fired power plant

A: Given Data⇒ Gas-fired power plant

Q: diagram of ‘regeneration cycle’ and state the advantages and disadvantages of regeneration.

A:

Q: Catalytic reforming process can be done using a semi-regenerative fixed process technology. This…

A:

Q: 1.What is the difference between the Water Tube Boiler and Fire Tube Boiler ?

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Atomic diffusion in solids

In material science, diffusion can take place in solid, liquid, and gases. In solids, atomic diffusion can take place with the help of thermally activated and randomly vibrating atoms. The atomic diffusion in solids is complex and very slow in comparison to atomic diffusion in liquids and gases because the interatomic distance between the atoms is smaller in solids as compared to liquids and gases.