What was the mass of water used if 249 g of a copper ball, initially at 314°C was immersed into the water and allowed to mix until thermal equilibrium was reached at 38.8°C? The specific heat of water is 4.184 J g ° C and that of copper is 0.387 J g ° C. The initial temperature of the water was 22.6°C.

What was the mass of water used if 249 g of a copper ball, initially at 314°C was immersed into the water and allowed to mix until thermal equilibrium was reached at 38.8°C? The specific heat of water is 4.184 J g ° C and that of copper is 0.387 J g ° C. The initial temperature of the water was 22.6°C.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter2: Steady Heat Conduction

Section: Chapter Questions

Problem 2.39P: The tip of a soldering iron consists of a 0.6-cm- diameter copper rod, 7.6 cm long. If the tip must...

See similar textbooks

Similar questions

8.592 kg of steam at a pressure of 20 bar and temperature of 300 deg C expands isentropically to a pressure of 0.5 bar. Determine the work done on steam in kJ during expansion For the steam table, please refer to the green book entitled " Thermodynamic Properties of Water Including Vapor, Liquid, and Solid Phases)
Imagine that we put a 140-g steel ball with an initial temperature of 119°C into a cup containing 140 g of water with an initial temperature of 11°C. What is the final equilibrium temperature of this system in degrees Celsius? The specific heats of steel and water are 450 J kg−1 K−1 and 4186 J kg−1 K−1,respectively.The final equilibrium temperature of this system is _______degreesC.
13 moles of monatomic ideal gas undergoes a thermodynamic process from point a topoint c, as shown by the PV diagram in Figure 1 i) Determine the work done ON the gas from point a to point c ii) Find the temperature of the gas at point b. b) 2 moles of diatomic gas has a constant volume of 2.0 L and a temperature of 2000 K. Ifthe temperature of the gas raised to 2800 K, find the thermal energy absorbed by thegas.
A 2.00 - mol sample of an ideal diatomic gas at a pressure of 1.00 atm and temperature of 440 K undergoes a process in which its pressure increases linearly with temperature, use P = Po + aT . The final temperature and pressure are 720 K and 1.60 atm. Determine (e) the change in internal energy, (b) the work done by the gas, and (c) the heat added to the gas. (Assume five active degrees of freedom . )
A 5kg Cu block at 200 C is submerged in 100 lb water at 10 C in an insulated vessel Determine the final equilibrium temperature.
An isolated piston inside a rigid, isolated cylinder, closed at both ends, has two chambers; one containing a two-phase water mixture and one containing a two-phase mixture of R-134a. If the temperature inside the chamber containing water is 85.9°C, determine the temperature inside the other chamber. Assume mechanical equilibrium. Do you have enough data to calculate the quality in both cases? Justify your answer.
Instructions: Show your entire solution. Indicate which table from the steam tables you utilized in your solution. 5. A 4.12-kg steam-water mixture at 1.0 MP is contained in an inflexible tank. Heat is added until the pressure rises to 3.5 MPa and the temperature to 400°C. Determine the heat added in kJ.
How many kilograms of -5 °C ice per day will melt and evaporate to steam after adding a total of 7500 kJ/hr?
An ideal gas of 4kg mass (MW=3g/mol and k=2.3) contained in a regulated mass system went through three processes in a cycle, one after the other. The initial conditions for the gas were 20kPa and 310K in the first step, and the pressure was isometrically increased by 30kPa. The gas was heated to 400 degrees Celsius using a technique defined by the equation PV3=C. Upon returning to its previous state, it exhibits polytropic behavior. Calculate the change in entropy for each of the processes.
What is the internal energy of 2.2 kg of dry saturated steam at 11 bars ?
A 10-g ice cube at -10°C is dropped into 40 g of water at 30°C. After enough time has passed to allow the ice cube and water to come into thermal equilibrium, what is the temperature of the water?
5kg of Steam at pressure of 4.9 bar is produced from water at 20°c. Determine the amount of heat supplied if the Steam is 0.9 dry.