What will be the rise in temperature in 30 minutes of a block of copper of 500-gram mass if it is joined to a cylindrical copper rod 20 cm long and 3.0 mm in diameter when a temperature difference of 80 degree Celsius is maintained between ends of the rod? The thermal conductivity of copper is 1.02 cal/cm2-sec-°C/cm (neglect heat losses). Please include FBD

What will be the rise in temperature in 30 minutes of a block of copper of 500-gram mass if it is joined to a cylindrical copper rod 20 cm long and 3.0 mm in diameter when a temperature difference of 80 degree Celsius is maintained between ends of the rod? The thermal conductivity of copper is 1.02 cal/cm2-sec-°C/cm (neglect heat losses). Please include FBD

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter4: Numerical Analysis Of Heat Conduction

Section: Chapter Questions

Problem 4.12P

See similar textbooks

Similar questions

To determine the thermal conductivity of a structural material, a large 15-cm-thick slab of the material is subjected to a uniform heat flux of 2500 W/m2 while thermocouples embedded in the wall at 2.5 cm. intervals are read over a period of time. After the system had reached equilibrium, an operator recorded the thermocouple readings shown below for two different environmental conditions: Distance from the Surface (cm) Temperature (C) Test 1 0 40 5 65 10 97 15 132 Test 2 0 95 5 130 10 168 15 208 From these data, determine an approximate expression for the thermal conductivity as a function of temperature between 40 and 208C.
A plane wall 15 cm thick has a thermal conductivity given by the relation k=2.0+0.0005T[W/mK] where T is in kelvin. If one surface of this wall is maintained at 150C and the other at 50C, determine the rate of heat transfer per square meter. Sketch the temperature distribution through the wall.
The thermal conductivity of fibreglass insulation at 67F is 0.02 Btu/h ft F. What is its value in SI units?
1.71 The thermal conductivity of silver at 212°F is 238 Btu/h ft °F. What is the conductivity in SI units?
A plane wall of thickness 2L has internal heat sources whose strength varies according to qG=qocos(ax) Where qo is the heat generated per unit volume at the center of the wall (x=0) and a is a constant. If both sides of the wall are maintained at a constant temperature of Tw, derive an expression for the total heat loss from the wall per unit surface area.
1.3 A furnace wall is to be constructed of brick having standard dimensions of Two kinds of material are available. One has a maximum usable temperature of 1040°C and a thermal conductivity of 1.7 W/(m K), and the other has a maximum temperature limit of 870°C and a thermal conductivity of 0.85 W/(m K). The bricks have the same cost and are laid in any manner, but we wish to design the most economical wall for a furnace with a temperature of 1040°C on the hot side and 200°C on the cold side. If the maximum amount of heat transfer permissible is 950 , determine the most economical arrangement using the available bricks.
Discuss the modes of heat transfer that determine the equilibrium temperature of the space shuttle Endeavour when it is in orbit. What happens when it reenters the earths atmosphere?
1.63 Liquid oxygen (LOX) for the space shuttle is stored at 90 K prior to launch in a spherical container 4 m in diameter. To reduce the loss of oxygen, the sphere is insulated with superinsulation developed at the U.S. National Institute of Standards and Technology's Cryogenic Division; the superinsulation has an effective thermal conductivity of 0.00012 W/m K. If the outside temperature is on the average and the LOX has a heat of vaporization of 213 J/g, calculate the thickness of insulation required to keep the LOX evaporation rate below 200 g/h.
Determine the heat conduction of a boiler if you are given the following data: The thickness of the boiler is 15 cm, the T1 is the temperature of the water is 25°C and the T2 of the steam is 110°C, the thermal conductivity The boiler material is iron (use presentation table), the boiler area is 4.5 m^2
Mechanical Engineering. Please help to solve, will upvote after. What is the change in length of a 5-m tin rod if the temperature changes from 11 to245°C?
In a glass plant in Cavite, a furnace has fire-brick walls made up of the following two materials in series : Non-corrosive brick as inner layer (material 1) Clay brick as outer layer (material 2) Thickness 4.5 inches 8 inches Thermal conductivity k1 k2 The temperature inside the furnace (inside wall surface of the non-corrosive brick) is found to be 1105 oF while the outside temperature (outside wall surface of clay brick) is 365 oF. This is not the desired temperature inside the furnace so engineers thought of lagging the furnace walls with another material to reduce heat loss. The additional lagging material consists of magnesia layer which is 2 inches thick and has a thermal conductivity of 0.04 Btu /h.ft.oF. During a test run on the furnace with the magnesia lagging material now, new temperature readings were recorded : Point of measurement Temperature reading Inside furnace (inside wall surface of non-corrosive brick 1355 oF Interface between…
One wall of a room measures 14 feet long and 8 feet high. It's contains a window 5 feet wide and 3.5 feet high. The wall has an R-Value of 15.5. the unit R-value of the window is 3.5. Find the rate of heat flow through the wall when the inside air temperature is 68 degrees Fahrenheit and the outside temperature is 5 degrees Fahrenheit.