When a stationary mass of gas was compressed without friction at constant pressure its initial state of 0.8 m3 and 0.105 MPa was found to change to final state of 0.40 m3 and 0.105 MPa. There was a transfer of 85 kJ of heat from the gas during the process.How much did the internal energy of the gas change ? * 1 Add File

When a stationary mass of gas was compressed without friction at constant pressure its initial state of 0.8 m3 and 0.105 MPa was found to change to final state of 0.40 m3 and 0.105 MPa. There was a transfer of 85 kJ of heat from the gas during the process.How much did the internal energy of the gas change ? * 1 Add File

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter2: Matter And Energy

Section: Chapter Questions

Problem 30RQ: A gas is compressed inside a compressor's cylinder. When the piston is at its bottom dead center,...

See similar textbooks

Similar questions

A gas is compressed inside a compressor's cylinder. When the piston is at its bottom dead center, the gas is initially at 10 psig, 65F, and 10.5 in3. After compression and when the piston is at top dead center, the gas is 180Fand occupies 1.5 in3. What would be the new pressure of the gas in psig?
Initial condition: T = 360Ch = 1860.8 KJ/kg Process: IsometricFinal condition: saturatedRequired: Final pressure
Question 1 0.2804 kg of nitrogen, originally in a cylinder at 200 kPa and 32 oC, is to be compressed polytropically (PVn = C) to a final pressure of 1380 kPa. The volume compression ratio is 5:1. For nitrogen, R = 297 J/kg.K and  = 1.41. Calculate:(a) The value of the index n(b) The work done during compression(c) The change in internal energy(d) The change in entrop
1 kg of steam at initial conditions of 5.1 MPa and 370 °C expands in a turbine until it becomes saturated. It is withdrawn and reheated to 340°C. After further expansion in the turbine to 160 , part of the steam is extracted for feedwater heating. The remaining steam expands to the condenser pressure of 0.018 MPa. For 1kg of steam, find Wnet, Ec, Ee and the ideal steam rate. Remember:1. For values taken from the steam tables: Use them as is, do not round off.2. For values obtained by interpolation and final answers obtained by solving, use FOUR (4) decimal places.PLEASE USE THE STEAM TABLE PROVIDED: https://docs.google.com/document/d/1crebk95lXFEAR5d6Y6LymXJNraO9WLgtNjquSlVOvVs/edit
Five cubic meter of nitrogen are heated at constant volume so that the pressure changes from 276 kPa abs to 1375 kPa gage, For nitrogen, R= 0.296 kJ/kg-K and Cp= 1.039 kJ/kg-K. Find the transferred heat. Choices: (a. 20,515 kJ; b. 17,835kJ; c.21,066kJ; d.15,065 kJ)
Box the final answer. Write legibly. Steam flows into a turbine at a rate of 3.5 kg/s and ¾ MW of heat are lost from the turbine. Ignoring elevation and kinetic energy effects, calculate the power output from the turbine in KW? Steam pressure entering the turbine is 62 Bar at 440ºC and leaves at 74 Kpa.
Task 5A sample of gas is compressed by an average pressure of 2 atm which decrease its volume from400 cm 3to 200 cm 3. During the process, 10 J of heat is rejected to the surroundings. Explain and demonstrate the application of the first law of thermodynamics to this system and calculatethe change in energy of the system.
104#1. an ideal gas with R=0.062 BTU/lbm-degree R and Cv=0.158 BTU/lbm-degree R undergoes athree process cycle in a cklose system. from the initial state of 20 psia and 570degree R, the gas is compressed at coinstant pressure to 1/5 of its initial volume, process 1-2; it is then heated isochrocally to state 3, process 2-3; and finally, it expands polytopically with index n=1.5 back to its initial state, process 3-1. determine the pressure, specific volumes and temperatures at cardinal points around the cycle and the cycle thermal efficiency.
1.One cubic meter of an ideal gas at 600K and 1000kPa expands to 5 times its initial volume as follows: (a) By a mechanically reversible , isothermal process (b) By a mechanically reversible adiabatic process (c) By an adiabatic, irreversible process in which expansion is against a restraining pressure of 100kPa. For each case, calculate the final temperature, pressure and the work done by the gas. Cp=21 J/mol-K.Single line text. Please answer step by step
A piston cylinder device has a volume of 0.04 m3 and initially contains air at 293 K and 1 bar. This device is used to perform a cycle in which the gas is heated at a constant volume until the temperature reaches 1000 K. The air is allowed to expand following an isothermal process until the volume is 3.5 times the original volume. It is then cooled at a constant volume process. The completion of the cycle is a PV1.36 = constant process back to the original state. For the air, the specific heat is cv =0.79 kJ/(Kg K) = constant and its gas constant is RG=0.287 kJ/(Kg K). Calculate the net work produced by this cycle, the required heat input to the cycle and its thermal efficiency. How much heat is removed from the system during the cycle? Could the heat removed from this cycle be used to heat or partial heat the water that is at an initial temperature of 298 K? Would you recommend designing a heat recovery for this purpose?
We take a 33 kg chunk of ice (Temp is 0°C) and submerge it in an isolated container. This container has 6 kg of water, and the water is 7°C. Answer the following: 1) How much ice from the block melts (in grams)? 2) What is the change in entropy for the entire system?
Calculate the amount of work necessary for the reversible compression of steam from 1 bar to 10 bar. The compression is to take place in a cylinder fitted with a weightless piston at the constant temperature of 500 oC. Under these conditions we have a superheated vapor. Assume that steam may be treated as an ideal gas. Report your answer in units of kJ/kg using three decimal places. For conversion, note that the molar mass of water is 18.015 g/mol.