When entering the command "service password- encryption" on a router, which of the following is true? As an example, it is used to protect the telnet password. b. It is used to encrypt all passwords. c. It's used to encode the password for the elevated user account (privileged exec mode). O d. Passwords for game consoles may be encrypted using it.

When entering the command "service password- encryption" on a router, which of the following is true? As an example, it is used to protect the telnet password. b. It is used to encrypt all passwords. c. It's used to encode the password for the elevated user account (privileged exec mode). O d. Passwords for game consoles may be encrypted using it.

A+ Guide To It Technical Support

10th Edition

ISBN:9780357108291

Author:ANDREWS, Jean.

Publisher:ANDREWS, Jean.

Chapter8: Network Infrastructure And Troubleshooting

Section: Chapter Questions

Problem 12TC

See similar textbooks

Similar questions

Which of the following statements about the router command "service password- encryption" is true? a. The telnet password is encrypted using it. b. It is used to encrypt each and every password. c. The privilege exec mode password is encrypted using it. It's used to encrypt the console password.
Which of the following statements concerning the command "service password- encryption" on a router is accurate? It's used to encrypt the telnet password, for example. b. All passwords are encrypted using it. c. It is used to encrypt the password for the privilege exec mode. O d. It's used to encrypt console passwords.
You have opened a telnet session on port 25 with your e-mail server. What commandcan you type within your telnet session to start an e-mail session? (Choose all thatapply.)a. STARTb. HELOc. EHLOd. WAZUP
Router5 is in rom mode, and there is an enable password on it which we don't know. Bring it back to boot in normally, set new enable password of 'cisco' and restore its configuration. IF the original configuration is restored, the router should be able to ping the others without any further configuration. If the interface (on Router5) are down (it will be red) after you restore, bring the interface up with 'no shutdown command' Wait until you see the messege "from loading to FULL, LOADING done" BEFORE TRYING TO TEST PING 0x2102 (boot normally) (default)0x2120 (rom mode)0x2142 (ignore nvram content) This is all ONE question, please answer full question.
Which file would you modify to permanently change the TCP/IP address of the firstwired NIC on a Fedora 20 system?a. /etc/sysconfig/network-scripts/ifcfg-eth1b. /etc/sysconfig/network-scripts/ifcfg-eth0c. /etc/sysconfig/network-scripts/ipcfg-eth0d. /etc/sysconfig/network-scripts/ipcfg-eth1
1. Which of the following is not usually implemented in the server-side code? a. Routing Code b. All of these are usually implemented in Server-Side Code c. Authentication Logic Code d. User Interface Code 2. True or False. The fetch method can only be used to make GET requests. a. True b. False 3. True or False. Node.js is a asynchronous event-driven framework. This means it can only handle one event at a time a.True b. False 4. When using the router level middleware in express, what must match for the Handler Method to be executed? a. None of these b. Path and URL c. Request and Response d. Method and Path
which of the following files are used by TCP wrappers? ( Choose two.) a) /etc/wrap.allow b) /etc/wrap.deny c) /etc/hosts.allow d) /etc/hosts.deny
Can you provide some explanation and steps to do , i am using ubuntu20.04 on windows 10 VMware. also i could able to config VPN connection to the server what is next step also i would like to use python for programming. task description is below. Thanks A UDP service FlagServ is running at flagserv.cse543.rev.fish:13337. This UDP service receives a target IP address from the user, and if the user is authenticated, it will happily send a flag (a special string) via UDP to port 13337 of the target IP. Your job is to write a program that retrieves the flag. FlagServ employs THE BEST AUTHENTICATION METHOD IN THE WORLD: Source-IP-based authentication, which means it authenticates all users based on their source IP addresses. If a user's source IP address is trusted, FlagServ will send out the flag to the specified destination (repeat: via UDP). Otherwise, it will send an error message back to the untrusted user (via UDP, too). The only trusted IP is 10.2.4.10. Your task is to break or…
Which router command describes "service password-encryption"? It encrypts telnet passwords. It encrypts all passwords. It encrypts privilege exec mode passwords. It encrypts console passwords.
The following program sets up a single client/server connection. When the client connects, the server reads any incoming data as text and prints it out one line at a time. If the server receives the string “shutdown”, then it closes the socket and exits. Download this program Download this program into GCC and run the code. Then update your code to allow for the server to manage concurrent connections on the same port. Use IP address 127.0.0.1. Page of 3 ZOOM /* Server code */ #define BUF_SIZE 1024 #define LISTEN_PORT 8080 int main(int argc, char *argv[]) { int sock_listen, sock_recv; int i, addr_size, bytes_received; int incoming_len; int recv_msg_size; struct sockaddr_in my_addr, recv_addr; int select_ret; fd_set readfds; struct timeval timeout={0,0}; struct sockaddr remote_addr; char buf[BUF_SIZE]; /* create socket for listening */ sock_listen = socket(PF_INET, SOCK_STREAM, IPPROTO_TCP); if (sock_listen < 0) { printf("socket() failed\n"); exit(0); } /* make local address…
Your DHCP server now uses these alternative DNS servers. In general, what is the quickest way for your clients to get the new settings? * Try a double restart of the computer. Enter ipconfig /registerDNS on the client. Watch for the DHCP client to request a lease renewal. O Launch ipconfig /renew on the client. Clear the server's DNS cache.
Step 1: Write a script to find and print your local IP address Use the following code: import socket hostname = socket.gethostname() local_ip = socket.gethostbyname(hostname) print(local_ip) Step 2: Write a script to find and print your OS platform and release (for example, "Windows version 10") Use the following code: import platform print(platform.system ()) print(platform.release ()) Step 3: Write a script to find and print a "ping sweep"? Use the following code: import os my_ip="192.168.10.103" # sub your ip address os.system('ping -n 4 {}'.format(my_ip)) Step 4: Write a script to find and print current day and time import time now = time.localtime() print(time.strftime("%m/%d/%Y %I:%M:%S %p", now)) Extra Credit: Add code to Step#4 which prints a greeting, either "good morning", "good afternoon", "or good evening", depending on the current time.