When the plant rotating equipment is installed what are possible environment problems will be faced and how the environment is polluted? In what way we can develop good environment around the plant rotating equipment?

Q: What improvements can be done to increase the efficiency to boil the water?

A:

Q: What do you mean by breakthrough curve for fixed-bed adsorption system?

A: Given: breakthrough curve for fixed-bed adsorption system

Q: . isothermal process is the best for production of maximum work for all wworking fluids False True

A: Below  is   PV  diagram showing  all  the  processes:-            From  above diagram, we find…

Q: Which statement is incorrect Select one: a. Diversity factor never will be less than unity b. Plant…

A: The diversity factor is always more than one, thus option a is correct. The statement b is also…

Q: Explain the temperature Changes: Heat Capacity ?

A: Temperature change- process where the temperature of body changes or hotness of body changes  i.e in…

Q: Mechanical working of metal is another name for_______________. a. Machining process b. Metal…

A: Mechanical working of metal is another name for Forming process. Answer: d. Forming Process

Q: why bare pipe has 0% efficiency and full covered insulate pipe has more efficiency

A: A thermal insulator has a low thermal conductivity and is a poor heat conductor. To reduce heat loss…

Q: In order to avoid the substantial cost of the installing high-pressure tubes. what is used in the…

A: In order to avoid the substantial cost of the installing high-pressure tubes, the heat transfer…

Q: or induced draft counter flow cooling tower O a. fan is kept at bottom of cooling tower and air and…

A: Induced draft — A mechanical draft tower with a fan at the discharge (at the top) which pulls air…

Q: the answer option C

A:

Q: 14. What type of reactor does this appear to be? 0.368+

A: this type of graph shown second order reaction.

Q: 2 B

A: To-Find:- Resultant at point C

Q: Which of the following does not belong to the group? force stress time velocity

A:

Q: Which one of given options is true? O Work surface after machining process transforms into machined…

A: Solution:

Q: What are the four ways we put fluids to work

A: Crystalloid IV solutions contain small molecules that flow easily across semipermeable membranes.…

Q: Which can do work faster per unit time?

A: In order to solve the problem,It is important to define the given options properly.

Q: In the wind experiment, what blade pitch angle results in maximum power output? O a. small and…

A:

Q: In sectional view, mechanical fasteners like bolts, screws, nuts are represented as___. a. Sectioned…

A: Sectional View

Q: Project 2: In company that designs road cars and heavy trucks, it important to make the proper…

A: Hi, thank youy for the question! Since we only answer up to 3 sub-parts, we’ll answer the first 3.…

Q: When does the impact occur?

A: Impact: It the force that is applied to the specimen or object from a certain height. These are…

Q: methods of temperature

A:

Q: Analyze the thermal power plant carefully and list all burn out products which are harm full for the…

A: Thermal power plants are known to pump out a lot of greenhouse gases and ash, which are by-products…

Q: What kind of power isn't used as a power source for driving machine tools?         a)Steam power…

A: Power: The rate of work done is known as power. Generally, mechanical power is required to drive…

Q: or safety of plant which department is responsible?

A: Given Data⇒ Department Safety of plant

Q: (b) State THREE (3) differences between cold working and hot working processes.

A: Deformation of the material will be done at a temperature less than recrystallization temperature is…

Q: The optimum effective temperature for human comfort is ?

A: For a human being,

Q: Distinguish between the Surface Loads and the Distributed Loads?

A: Load is defined as an external force or a couple to which a member is subjected during its…

Q: Which statement is incorrect Select one: a. Diversity factor never will be less than unity b. Plant…

A: Given: To select the wrong statement

Q: Which can do work faster per unit time? (A) 2300-W engine (B) 3-hp engine (C) 1.5 kW engine (D)…

A: To solve this question, each options need a proper analysis and conversion into same units.

Q: Does the tool (WRENCH) have any fragile or delicate parts that need to be protected? If so, how do…

A: Solution:   A Wrench is a tool which produces torque when a certain amount of force is applied in…

Q: Draw Schematic diagram of Hydro Power Plant indicating all the parts and explain the working of the…

A: The schematic diagram of the Hydro Power Plant is shown below in three parts. First part:

Q: What is the energy produced in

A: To find Energy produced per month (MW)

Q: what are some of the ways by which the blades of windmill be improved

A: Wind energy is an example of renewable energy and its use never harms the environment. But it is an…

Q: Write one to two paragraph Executive Summary of a shell and tube heat exchange and the manufacturing…

A: A Heat exchanger is a device which is used to transfer heat from one fluid to another. There are…

Q: Describe the performance of a flat plate collector with regards to the energy flow.

A: Describe the performance of a flat plate collector with regards to the energy flow.

Q: Total heat transfer rate

A: 1). first find the reynold's number and determine whether tye flow is laminar or turbulent?? 2).…

Q: Identify the energy storage device a. Flywheel b. Winch c. Gear d. Screw jack

A: To find : which of the following is energy storage device

Q: w windmill works.

A: Windmill has baled or sails. The basic principle is that it converts the kinetic energy of wind into…

Q: Which statement about hydroelectric power plant is wrong? Select one: O a. Its construction coast is…

A: Let us discuss all the options   (a) Its construction cost is very high and takes a long time for…

Q: Explain the Electromechanical Energy conversion and its features

A: Electromechanical energy conversion means conversion from the electrical form of energy into the…

Q: The is the actions associated with equipment repair after it is broken. Select one: O a. Rolling O…

A:

Q: An engineer was tasked with evaluating a heat and power generation unit for an aluminium smelting…

A: Given data: Power requirement per smelting processing line = 0.6 MW Overall thermal efficiency = 35…

Q: Which one of given options is true?   a)Machined surface after drilling process turns into work…

A: Which one given option is true?

Q: what the functions of well head in brief and Explain the functions???

A: Image of a wellhead:

Q: 5. Mention the level measurement system, which protects the DP transmitter from the corrosive…

A: In the bubble type level framework, fluid is not entirely set in stone by estimating the tension…

Q: what is the decrease in internal energy?

A: The initial volume of the air is, V1=80 ft3=2.26535 m3 The initial pressure of the air is, P1=350…

Q: Insulation -Lead shot W To Control knob Thermal reservoir explain about the picture about…

A:

Mechanisms of heat transfer

Heat transfer is an essential discipline in thermal engineering that deals with the transfer, conversion, usability, and creation of heat or thermal energy. Transfer of heat occurs through various mechanisms like conduction, convection, radiation, and change of phases. All these mechanisms have distinct characteristics, but these mechanisms can simultaneously occur in an identical system.