Which of the following is a correct statement relating Control Unit of Von Neumann computer? O a. Control unit is not responsible for decoding of instructions. b. Control Unit ensures that all the operations in the processor are asynchronous. Control unit has general purpose registers that can be used in arithmetic and logical operations. Od. Control Unit contains both instruction pointer and program counter.

Which of the following is a correct statement relating Control Unit of Von Neumann computer? O a. Control unit is not responsible for decoding of instructions. b. Control Unit ensures that all the operations in the processor are asynchronous. Control unit has general purpose registers that can be used in arithmetic and logical operations. Od. Control Unit contains both instruction pointer and program counter.

Name: Which of the following is a correct statement relating Control Unitof
Uploaded: 2024-03-20T06:51:23.000Z
Channel: Bartleby
Description: Which of the following is a correct statement relating Control Unitof Von Neumann computer?O a. Control unit is not responsible for decoding of instructions.b.Control Unit ensures that all the operations in the processorare asynchronous.C.Control un

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

P1:Given the following memory values and a one-address machine with an accumulator,whatvalues do the following instructions load into the accumulator?·Word 20 contains 40.·Word 30 contains 50.·Word 40 contains 60.·Word 50 contains 70.a. LOAD IMMEDIATE 20b. LOAD DIRECT 20c. LOAD INDIRECT 20d. LOAD IMMEDIATE 30e. LOAD DIRECT 30f. LOADINDIRECT 30
Which of the following instructions requires the most care? Justify your reasoning. I Gather system time, flush memory, and access user memory (iv) Users' Space Writing (v) Moving information from one register to another (vi) Putting a stop to distractions (vii) Switching from interactive to observing mode
Here are some registers and storage locations during the run of a program.For this example, all numbers are hex.eax contains 300ebx contains 3000The doubleword at memory location 300 contains 500The doubleword at memory location 10 contains 70 What is in eax after the command addl $10, %eax executes? a. 310 b. 510 c. 370
Assume the two instructions below are executed.AND R4, R4, #0STR R4, R7, #-1Which one of the statements below is correct? Group of answer choices The execution sets the value at memory address with label H to x1233. The execution sets the value in R4 to x400F. The execution sets the value at memory address with label H to x1234. The execution sets the value at memory address with label H to 0. The execution sets the value at memory address with label B to x1233.
What will be the contents of BX after the following instructions execute?mov bx,5stcmov ax,60hadc bx,ax
A particular application has the following mix of instruction types: a) What percent of the instructions use data memory? b) What percent of instructions use instruction memory? c) What percentage of the instructions use all five stages (Fetch, Decode, ALU, Memory, Writeback) of instruction execution?
Q2) (a) For the expression given ( An + B’n ) * ( C’n + Dn ) , you should write Zero-Address instructions to compute the same expression? Also mention what type of computer organization will use these instructions.
From the given code from step 1-step19 a- What are the memory location addresses that will be accessed in memory data segment in this program? b- What is the content of each memory location accessed in memory data segment in this program? c- What does the content of each memory location refer to?
Which of the following refers to the associative memory? A. the address of the data is generated by the CPU B. the address of the data is supplied by the users C. there is no need for an address i.e. the data is used as an address D. the data are accessed sequentially E. None of the above
Assume you have a computer that runs a programme that is 50% floating point multiply, 20% floating point division, and the other 30% is made up of other instructions. a. Management desires that the machine run four times faster. You can speed up the division by no more than three times and the multiply by no more than eight times. Can you accomplish management's target with just one enhancement, and if so, which one? b. What is the speed of the new machine in comparison to the original machine if you enhance both multiply and divide?
Which of the following is correct regarding Memory-Mapped I/O? Select one: a. Memory-Mapped I/O is more complex and inflexible in handling I/O operations. b. The same memory reference instructions (read/write) can be used for I/O transfers. c. There are separate input and output instructions to handle I/O data transfers. d. There is a separate memory and I/O address space. O e. The available memory address space is larger when using Memory-Mapped I/O.
11. Which of the following is not a form of memory ? a. Instruction cache b. Instruction register c. Instruction opcode d. Both a and b