Answered: wood-stave penstock of 1.8 m diameter…

Name: A wood-stave penstock of 1.8 m diameter is wrapped with steel hoops an
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: A wood-stave penstock of 1.8 m diameter is wrapped with steel hoops and subjected to a fluid pressure of 380 KPa. If the allowable tension in the hoop is 42.4 kN, what is the maximum hoop spacing?

Engineering

Mechanical Engineering

wood-stave penstock of 1.8 m diameter is wrapped with steel hoops and subjected to a fluid pressure of 380 KPa. If the allowable tension in the hoop is 42.4 kN, what is the maximum hoop spacing?

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter4: Coplanar Equilibrium Analysis

Section: Chapter Questions

Problem 4.153P: Repeat Prob. 4.152 assuming that the 400-kN force is applied at O instead of L.

See similar textbooks

Similar questions

Repeat Prob. 4.152 assuming that the 400-kN force is applied at O instead of L.
The 12-ft wide quarter-circular gate AB is hinged at A. Determine the contact force between the gate and the smooth surface at B due to water pressure acting on the gate. Use =62.4lb/ft3 for water.
A vertical cylinder gasoline storage tank is 30m in diameter and is filled to a depth of 15m with gasoline of mass density 740 kg/m³. if the shell plating has an allowable stress of 100 MPa, calculate the required wall thickness at the bottom of the tank.
A thin-walled hollow sphere 3.8 m in diameter holds helium gas at 1767 kPa. Determine the minimum wall thickness of the sphere in mm if its allowable stress is 84.8 MPa.
The strength per meter of the longitudinal joint in the figure is 480 kN, whereas or the girth joint is 200 kN. Determine the maximum diameter of the cylindrical tank if the internal pressure is 1.5 MPa.
A cylindrical steel tank having an internal diameter of 50 in. is submerged in seawater (weight density =64⁢ lb/ft3) to a depth of 9750 ft. The internal gage pressure in the tank is 1600 psi. (a) If the allowable stress of the steel is 32 ksi, what is the minimum allowable outside diameter of the tank? (b) What is the maximum tensile stress before the tank is immersed? Determine the external pressure of the seawater at a depth of 9750 ft. po= psi Determine the maximum magnitude of σr produced in the tank. σr = psi Based on the maximum magnitude of σr produced in the tank from Part 2, is there an outside diameter for which the radial stress magnitude will exceed the allowable stress of the steel in this case? More calculations are needed. No Yes For this case, choose the correct statement regarding the maximum magnitude circumferential normal stress. It occurs at the outer surface of the tank, and it is tensile. It occurs at the outer surface of the tank, and it…
A cylindrical pressure vessel has an inner diameter of 4 ft and a thicknessof 1 2 in. Determine the maximum internal pressure it can sustain so that neither its circumferential nor its longitudinal stress component exceeds 20 ksi. Under the same conditions, what is the maximum internal pressure that a similar-size spherical vessel can sustain?
Two hemispherical shells of inner diameter 1m are joined together with 12 equally spaced bolts. If the interior pressure is raised to 300kPa above atmospheric pressure, determine the tensile force in each bolt.
A water tank 3m in diameter and 6m high is made from 12mm thickness of steel. When the tank is filled with water: - Determine the circumferential stress - And the tension force in the vessel
The manhole cover of an ammonia storage tank is to be held by 25 stud bolts. If the pressure inside the storage tank will remain constant at 12.5 kg/cm2 and the manhole diameter is 508 mm, what should be the stress area of the carbon steel bolts?
The 3 × 4-m side AB of a tank is hinged at its bottom A and is held in place by a thin rod BC. The maximum tensile force the rod can withstand without breaking is 200 kN, and the design specifications require the force in the rod not to exceed 20 percent of this value. If the tank is slowly filled with water, determine the maximum allowable depth of water d in the tank.
Your answer is partially correct. A homogeneous, 4-ft-wide, 9.8 -ft-long rectangular gate weighing800lbis held in place by a horizontal flexible cable as shown in the figure below. Water acts against the gate, which is hinged at point A. Friction in the hinge is negligible, Determine the tension in the cable. AssumeL1=9.8ft,L2=7.2ft, andθ=57∘. Please type answer note write by hend.