Write a program to execute the instruction ldaa #$50 1000 times. This is howwe can make a delay. If the execution time of the instruction ldaa #$50 is 1ms, thenexecuting the instruction for 1000 times will make a delay for 1 sec. Example: turn a LEDon, then execute the delay to wait 1 sec to keep the LED on for 1 sec, then turn it off.

Write a program to execute the instruction ldaa #$50 1000 times. This is how we can make a delay. If the execution time of the instruction Idaa #$50 is Ims, then executing the instruction for 1000 times will make a delay for 1 sec. Example: turn a LED on, then execute the delay to wait 1 sec to keep the LED on for 1 sec, then turn it off.

Write a program to execute the instruction ldaa #$50 1000 times. This is how we can make a delay. If the execution time of the instruction Idaa #$50 is Ims, then executing the instruction for 1000 times will make a delay for 1 sec. Example: turn a LED on, then execute the delay to wait 1 sec to keep the LED on for 1 sec, then turn it off.

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Translate the following machine code into English. There is no need to trace the execution of the program. Write one English sentence per instruction. For example, for instruction 0xB103, you would write, "Compare register 1 to register 0; if they're the same, jump to address 0x03." 0x10AA 0x2FB0 0xBF00 0x7521 0xA504 0x40E1 0x50FF
Write an assembly language program that reads a specified number of positive integer inputs from standard input and outputs the largest value that was read. For example, if standard input contains: 5 3 2 7 9 4 The 5 indicates that there will be 5 additional values. Then program should read those 5 additional values and print the largest of them (e.g 9 in this case). One strategy here would be to outline the program in high-level language code and then translate it into assembly code. Be sure to assemble, run and test your program to ensure that it is syntactically correct and that it works correctly. The program should work for any valid input not just the one shown above.
Write a MARIE assembly program that implements the below Pseudocode:z=0 Input x If x=0 X=x+3 Input y If y>0 z=x*y Print z . For example, if the entered values are 9 and 5, then the output should be 45.N.B: You should include the MARIE code in your Answer (not a screenshot!), with an explanation of your code. Example: Add One /Add 1 to AC Add a screenshot of the simulation, showing the result (A screenshot of the MARIE Simulator window after running the program). Instructions: Use “ORG” instruction to start your program at address equivalent to 51210. Use x = 5 and y = 5 Do not forget to change the representation of the Input and Output windows in the simulator to Decimal. You should include the proper labels and directives at the end of your program.
Write an LC-3 assembly language program that counts the number of 1s in the value stored in R0 and stores the result in R1. For example, if R0 contains 0001001101110000 (x1370), then after the program executes, the value stored in R1 would be 0000000000000110 (decimal 6) Here are some hints ORIG x3000 AND R5, R5, #0 ADD R5, R5, #1 ;R5 will act as a mask AND R1, R1, #0 ;zero out the result register AND R2, R2, #0 ;R2 will act as a counter LD R3, NegSixt MskLoop AND R4, R0, R5 ;mask off the bit Add code here... if you want more than a 0 Solicit the number to be inspected via the keyboard. 10 points for a single digit (e.g. 5) decimal number, which must be converted to binary. 20 points for a two digit (e.g. 55) decimal number, which must be converted to binary.
What happens if an instruction isn't received, and it's recorded on VA page 30? Software-managed TLBs are quicker than hardware-managed TLBs in the following scenarios:
Write a new program in MIPS Assembly language using your LFSR function from the first problem. Start from state 0x00000001, then run a loop counting all the possible states in the LFSR before it cycles back to 0x00000001. This is shown by the following pseudocode: count = 0; initial = state = 0x00000001; do { state = LFSR(state); count++; while (state != initial); print count; Verify that the number of states is (2^15) - 1 = 32767 . Your program should complete within 30 seconds. If it takes longer then you likely have entered an infinite loop.
Give downvote if plagiarized or from internet A program is run on a system with two types of machine language instructions: type A instructions each require 3 clock cycles, while type B instructions each require 1 clock cycle. If 100 million type A instructions and 400 million type B instructions are executed, what is the CPI for this program? A program is run on a system with two types of machine language instructions: type A instructions each require 3 clock cycles, while type B instructions each require 1 clock cycle. If 100 million type A instructions and 400 million type B instructions are executed, what is the CPI for this program?
Implement a new unary instruction in place of N0P0 called ASL2 that does two left shifts on the accumulator. V should remain unchanged, but N and Z should correlate with the new value in the accumulator, and C should be the carry from the second shift. Write a program that tests all the features of the new instruction.
In the typical five stages of execution studied, which type of instruction actually does active work in each and every one of those five stages? Choose the best answer. Group of answer choices load word store word vector add add immediate None of the above add
Consider a program that declares global integer variables x, y[10]. Thesevariables are allocated starting at a base address of decimal 1000. All thesevariables have been initialized to zero. The base address 1000 has been placed in$gp. The program executes the following assembly instructions:lw $s1, 0($gp)addi $s1, $s1, 25sw $s1, 0($gp)lw $s2, 12($gp)add $s2, $s2, $s1sw $s2, 8($gp)sw $s2, 12($gp) What are the memory addresses of variables x, y[0], and y[1]? What are the values of variables x, y[0], y[1], and y[2] at the endof the program?
Give a program with 106 instructions divided into classes as follows: 10% class A, 20% class B, 50% class C, and 20% class D Clock Rate CPI Class A CPI Class B CPI Class C CPI Class D Computer 1 2.5 GHz 1 2 3 3 Computer 2 3.0 GHz 2 2 2 2 What are the clock cycles to execute this program on each computer? What is the average CPI for each computer? Which computer is faster? By how much?
What is the minimum number of cycles needed to completely execute n instructions on a CPU with a k stage pipeline? What if you have 2 pipelines of k stages each?