Write a program which computes the power dissipated in a resistor of resistance R. Prompt the user for the value of R, the value of the current I, then display the result on the standard output as shown below. (Hint: P= RI) Enter the value of resistance R: ** Enter the value of current I: ** The power dissipated in R is: **

Write a program which computes the power dissipated in a resistor of resistance R. Prompt the user for the value of R, the value of the current I, then display the result on the standard output as shown below. (Hint: P= RI) Enter the value of resistance R: Enter the value of current I: The power dissipated in R is: **

C++ Programming: From Problem Analysis to Program Design

8th Edition

ISBN:9781337102087

Author:D. S. Malik

Publisher:D. S. Malik

Chapter6: User-defined Functions

Section: Chapter Questions

Problem 30SA

See similar textbooks

Similar questions

Implement a program which divides a user input by 8 using only bit shift. Your programshould include a proper and useful prompt for input, and print the results in a meaningful manner
Write a program that operates a train crossing light. The lights should flash at a rate of 2 Hz (on, off, on, off in 1 second) and operate for 20 seconds. in TinkerCad with Code
Write a program in cpp that takes three inputs from the user and output the mean and median of the numbers (for example, if the numbers are 4, 9, 6 the median for these number is 6)The program should ask the user for three number and choice of operator i.e. Mean or median until user enters -1 to end the operation
Write a program whose input is two integers. Output the first integer and subsequent increments of 5 as long as the value is less than or equal to the second integer. Ex: If the input is: -15 10 the output is: -15 -10 -5 0 5 10 Ex: If the second integer is less than the first as in: 20 5 the output is: Second integer can't be less than the first.
Write a program to generate a four-tone siren using the speaker on D12PU board with each tone lasting for one second. The frequencies of these four tones are 100 Hz, 250 Hz, 500 Hz, and 1000 Hz. USE C PROGRAMING
write a python code that decodes the coloured bands on a resistor.Each colour band printed on a resistor has a corresponding numeric value, as shown in the table below: Colour Numeric value black 0 brown 1 red 2 orange 3 yellow 4 green 5 blue 6 violet 7 grey 8 white 9 To calculate the total resistance value, the following formula should be used: resistance=(10a+b)⋅10^c where a, b, and c are the numeric values of the first, second, and third colour bands respectively. For example, let's say that the colour bands on a resistor are red-green-orange. In this case, a=2, b=5, and c=3 (using the table). Hence the resistance value is 25000 ohms: resistance=(10*2+5) x 10^3=25000 ohms Your task is to write a program which asks the user to input the three colour bands. The program should then calculate and output the resistance value indicated by the bands. As part of your solution, you must define and use a function named colour_to_number. This function should take…
Write a program in Python that accepts two integer inputs. One input will serve as the starting point and the other one serves as the ending point. Run a number through the range of starting and ending point. If the current number is a factor for the ending number, break it. Starting point is exclusive in factoring. Inputs 1. One line containing an integer for starting point 2. One line containing an integer for ending point
Write a program that mimics a calculator. The program should take as input two integers and the operation to be performed. It should then output the numbers, the operator, and the result. (For division, if the denominator is zero, output an appropriate message.) Some sample outputs follow:3 + 4 = 713 * 5 = 65
Write a program that converts an input inch(es) into its equivalent centimeters.
Write a program whose inputs are three integers, and whose output is the smallest of the three values. Ex: If the input is: 7 15 3 the output is: 3
Write a Python program that allows the user to enter any integer value, and displays the value of 2 raised to that power.
Write a java code for below also attached output please answer asap