Write an 8051 asm program to design a voltage level indicator system using potentiometer and LEDS. The system must display the different level of the voltage with the help of 5 LEDS as per following conditions. a) If the voltage is between 0 to 1V glow LED1 p) If the voltage is between 1 to 2V glow LED1 and LED2 c) If the voltage is between 2 to 3V glow LED1 to LED3 d) If the voltage is between 3 to 4V glow LED1 to LED4 e) If the voltage is between 4 to 5V glow LED1 to LED5

Write an 8051 asm program to design a voltage level indicator system using potentiometer and LEDS. The system must display the different level of the voltage with the help of 5 LEDS as per following conditions. a) If the voltage is between 0 to 1V glow LED1 p) If the voltage is between 1 to 2V glow LED1 and LED2 c) If the voltage is between 2 to 3V glow LED1 to LED3 d) If the voltage is between 3 to 4V glow LED1 to LED4 e) If the voltage is between 4 to 5V glow LED1 to LED5

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Computer Science A circuit for two output ports (A&C) of the AVR ATmega16 microcontroller each connected to 8 LEDs. Write a program to control the LEDs in a sequence shown by stepping to lit on the LED sequentially as in the figure by toggling the LED at the same time for both ports (500mS) ending at the last state of the figure and looping back inversely to the start. This s done for 3 times back and forth.
Draw the high level state machine and data path for: an elevator that can move between floors 1 and 20 of a building. The destination of the elevator can be set by pressing the button for a specific floor, the value representing the desired floor is F. Once the value of F is input, if the current level C is greater than F the elevator will descend one floor per clock cycle. If the C is less than F, the elevator will ascend one floor per clock cycle. If C is equal to F, the elevator will not move. If there is no desired floor currently input, the elevator will remain idle until a floor is selected. Assume the elevator initial starts at level 1. The elevator cannot go below floor 1 or above floor 20. For any multibit inputs, outputs, or variables, state how many bits are needed.
Program a circuit where a yellow LED light will turn on when a button is pressed and remain on for 4 seconds. Then, a red light will flash at 2 Hz for 8 seconds. C++
write a C program that utilizes the RTC alarm to toggle an LED every five seconds
Write a C++ code to program and arduino board to control 3 lights(red, yellow, green). Red stays ON for 5 seconds and goes OFF, YELLOW stays ON for 5 seconds and goes OFF, GREEN stays ON for 5 seconds and goes OFF. This whole process repeats forever.
Write a C program using Microchip Studio for 3 traffic lights that count down from 60 to 0 one by one with a delay of 3 seconds between each, then implement the program using SimulIDE (use 7-segment display to show the timer)
Answer the given question with a proper explanation and step-by-step solution. Programming the Pico micropython Write a code with helper functions that makes 4 sounds with 250 Hz, 500 Hz, 750 Hz, and 1000 Hz of PWM frequency by the Cytron board’s Buzzer (connected to GP18), respectively, every 1 sec (each sound lasts 0.25 sec) if you press and hold GP20 button. Also, the code should play the same 4 notes in a reverse sequence from highest to lowest frequencies every 1 sec (each sound lasts 0.25 sec) when the GP22 button is pressed. In addition to that, your code should turn on the LED of GP2 while making 250 Hz sound, the LED of GP3 while making 500 Hz sound, the LED of GP4 while making 750 Hz sound, and the LED of GP5 while making 1000 Hz sound. Moreover, nothing should happen if you press both GP20 and GP22 buttons at the same time. You SHOULD define helper functions to be called for making each sound and turning its corresponding LED on. You may need another function to be defined…
Boolean Logic Draw the truth table for the following functions: F(A,B)=AB+(A+B) F(A,B,C)=AB+BC+CA F(A,B,C,D)=ABC+ABD+BC¯D Digital Circuits Draw the truth tables for the following Boolean expressions. xy+yz+xz x¯y+yz¯+x¯z (x⊕y)+(y⊕z)+(x⊕z) (xy)¯⊕z Draw circuit diagrams implementing each of the above expressions. You may simplify the expressions or not, as you choose. You may use any of the six fundamental logic gates (AND, OR, NOT, NAND, NOR and XOR).
write a C-program that will accept a numeric value of the resistor from the technician and provide an output the 3-color resistor code to the monitor. formula for find the 1st band, 2nd band and 3rd band resistor color in c program, based on a given number?
Program a circuit where a yellow LED light will turn on when a button is pressed 4 times and remain on for 4 seconds. Then, a red light will flash at 2 Hz for 8 seconds.
You need to program the logic for an autonomous road line painting vehicle. The vehicle (flashes yellow hazard lights during operation) is responsi a solid yellow line when the road bend is 45 degrees or more. When the road curvature is straight (or less than 45), a white dashed line must be pa intersection, the painting must stop and resume once past the intersection. When the vehicle reaches the final destination or at any time, should th deplete, the vehicle must stop and the red hazard lights must be turned on. Write down the procedure for a computer to perform this task as well-written pseudo-code. Your pseudo-code must be explicitly stated in low-level could be easily translated into a computer program by a programmer.
Write a programming code for the automatic sled router in microcontroller (menu selection, indicators, inputs and motor controls) Requirements of the automatic router design1) Use high torque 12V DC motor for router bit rotation (cw & ccw)2) Use two stepper motors (12V) for linear translation in xy directions3) Allow manual adjustment on the cutting depth by user4) Provide xy motion control for automation of the leveling process5) Utilize sensor to limit the machining range (small size will be faster)6) Use latch or pushbutton for machine operation (speed selection - router bit & xy translation, rotational direction of the router bit, start/stop, emergency stop, home positioning)