Write relation of static head with co-efficient of discharge.

Q: the hydraulic cycle in figure consist of:7-

A:

Q: Explain the working principle and applications of centrifugal pump, turbine, gear and axial flow…

A: Centrifugal pump: A centrifugal pump includes imparting energy to the fluid through a centrifugal…

Q: Min. power required to pump the water

A: Given data;   ρ=1850 kg/m3m=2.5 kg/s∆p=130kpa=130000 Pa

Q: (A) Compute the volumetric efficiency of hydraulic motor with a displacement of 0.00985 Vrev at 2400…

A:

Q: Water is pumped through a cast iron pipe (D-6 in). The pump is 75 % efficient. Calculate the…

A:

Q: List any four advantages of the Horizontal Axis Wind Turbine.

A:

Q: Effect of vane angle of a pump head against discharge,using equation and diagram 12:16

A: following is the answer to above question-

Q: Calculate the mass flow rate of air through the compressor.

A: Given Data The initial temperature is:Ti=20°C The volume flow rate is:V˙=120litres/minute=120×10-3…

Q: nthalpy turbine

A: given:

Q: Compare a orifice plate for low speed to a Pitot Static Tube.

A: Orifice plate is a flow rate measuring device used for restricting flow, for reducing pressure. It…

Q: C- Mention three of the advantage of the positive displacement pump?

A: The question given is

Q: A designer needs a quarter-turn valve to flow approximately 10 GP an inlet pressure of 3000 psig…

A: Flow Rate Equation

Q: Q. Define coefficient of discharge and write equation for actual discharge.

A: Coefficient of dischargeCoefficient of discharge is defined as the ratio of  the actual flow…

Q: Determination of Discharge Thru a Siphon

A: Given Height = 83.5 cm To find Theoretical discharge Actual discharge Difference percentage

Q: A cylinder with a bore diameter of 1.5 in and a rod diameter of 0.625 in is to be used in a system…

A:

Q: 6. A pump draws water from a sump through a vertical 6" pipe. The pump has a horizontal discharge…

A:

Q: Q- (A) Compute the volumetric efficiency of hydraulic motor with a displacement of 0.00985 Vrev at…

A: Given data: Volumetric displacement, VD = 0.00985 l/rev Speed of the motor, N = 2400 rpm Actual…

Q: Explain major impact all major losses through the pipes.

A:

Q: A cylinder with a bore of 4.5 inches and a rod diameter of 1.5 inches is to be used in a system…

A:

Q: Figure shows two possible locations for a water pump in a piping system that pumps water from the…

A: Net positive suction head (NPSH) can be defined as the measurement of fluid's pressure on the…

Q: Oil at 24 gpm and 1200 psi enters the low-pressure inlet of a 4:1 Racine pressure intensifier. Find…

A: Introduction: The Racine pressure intensifier is used to boost the oil or air exit pressure. It…

Q: A gear pump has a 75-mm outside diameter, a 55-mm inside diameter, and a 30-mm width. If the actual…

A:

Q: Lukewarm water at 60 °C in a storage tank is being pumped at 300 L/min from the tank. The line from…

A: Water temperature, T=60oCWater flow rate, Q=300 L/min=300*10-360m3/s=0.005 m3/sLength of suction…

Q: Write relation of dynamic head with co-efficient of discharge.

A:

Q: estimate the volume flow rate of water through the siphon

A: Given data: Apply Bernoulli’s equation between the free surface of the tank and the exit of the…

Q: A centrifugal pump takes brine from the bottom of a supply tank and delivers it into the bottom of…

A: Volume flow rate Q=400 gal/min=0.0252361m3/s h=150 ft length of pipe, L=600 ft Diameter for 4 in…

Q: Include a free body diagram.  pump draws water from a sump through a vertical 6′′ pipe. The pump…

A:

Q: Calculate the discharge throug

A: To find Discharge

Q: 3. Critically explain the working of the excavator with respect to the hydraulic circuit drawn.

A:

Q: FIND THE TOTAL DYNAMIC HEAD IN METER OF THE PUMPING SYSTEM DRAW THE SCHEMATIC DIAGRAM OF THE PUMPING…

A:

Q: For flow nate 28 Lis rale Sind pump Power

A:

Q: efine and discuss the important parts of the Duplex Pump.

A: defination a pump with two cylinders especially : one whose plungers are driven directly by the…

Q: Explain what is meant by a hydraulically balanced vane pump. How is this accom- plished?

A: INTRODUCTION : A vane pump is a positive displacement pump which is use to maintains a constant flow…

Q: 29. A cylinder with a bore diameter of 50 mm and a rod diameter of 20 mm is to be used in a system…

A:

Q: What is hydraulic head?

A: also called as ' Total head' of a fluid SI unit - meter

Q: List main probable causes and solutions for troubleshooting in pumps. (any four reasons and…

A: Four reasons for troubleshooting of pumps are- 1.Lack of Prime, 2.Loss of Prime, 3.Suction is too…

Q: What is performance characteristics of a centrifugal pump

A: A centrifugal pump is designed to develop certain manometric head and discharge at constant speed…

Q: Determine the least number of stages for a multi-stage pump to deliver 80 L/s against a total head…

A:

Q: A centrifugal pump takes brine from the bottom of a supply tank and delivers it into the bottom of…

A: Given: Difference in the level of the supply tank and discharge tank: →Z2-Z1=150 ft Length of the…

Q: What is double reciprocating pump?

A: Given Data⇒Double reciprocating pumpProblem definition⇒Problem says What is double reciprocating…

Q: Problem 1 consists of ten questions to be solved consecutively. The objective is to pump 280 gal/min…

A: givenQ=280 gal/ minQ=0.028m3/s312,40 such steel pipe ⇒ID⇒90.12mm

Q: Discuss the relation between the head pressure and flow rate for the benefits of connecting the…

A: When the two pumps are connected in series, their resultant pump performance curve is given by…

Q: A centrifugal pump has the following specifications: I= 20 mm 2= 70 mm bi = 20 mm %3! b 10 mm a =…

A:

Q: Write about the working and construction of a compressor which is having a cooling system in order…

A: Working and construction of a compressor :-

Q: Ex2-The two pumps (n=1800 rpm) each have the following characteristics: h= (100, 90, 80, 60, 40,…

A:

Q: It is desired to deliver 5gpm at a head of 640ft in a single stage pump having a specific speed not…

A: correct answer: 2

Q: Determination of Discharge Thru a Siphon Vol

A: Given Distance = 83.5 cm = 0.835 m To find Trials Theoretical discharge Actual discharge Difference…

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.