y = 0.52 m 0 = 50° -b= 0.8 m

Q: Figure (4) Question (: The rectangular channel has a transition that causes its width to narrow to…

A: This problem is related to fluid mechanics. Fluid mechanics is the subject of mechanical engineering…

Q: Consider water flow over a 0.80-m-high sufficiently long broad-crested weir. If the minimum flow…

A: Given Data: The total head is: H=0.8 m The downstream depth is: h2=0.5 m

Q: Water flows in a canal at an average velocity of 6 m/s. Determine if the flow is subcritical or…

A: For flow to be subcritical or supercritical following condition should be fulfilled Subcritical…

Q: The flow rate passing through a rectangular channel with a base width of 4 meters and a water depth…

A:

Q: A rectangular channel with a bottom width of 7 m discharges water at a rate of 45 m3/s. Determine…

A: The data given is, Discharge, Q = 45 m3/s Rectangular channel width, b = 7 m

Q: The best hydraulic cross section for a trapezoidal channel of base width b is one for which the…

A: The hydraulic cross-section best for the trapezoidal channel of the given base width and a specified…

Q: A trapezoidal channel has a base width of 8.3 m and side slopes that rise 1 m vertically for every 2…

A: Given Data  Width, B=8.3 m Horizontal = 2 Vertical =1 Slope=m=2 Depth of the flow (y)=2.7m…

Q: Water at 20°C flows at a depth of 0.4 m with an average velocity of 4 m/s in a rectangular channel.…

A: Given data: Depth, y = 0.4 m Average velocity, V = 4m/s   Assumption: For convenience we take…

Q: A triangular open-channel (n=0.014) has a side slope of 2H:1V. The flow depth is 3m when the slope…

A: Given: Manning's constant→n=0.014 Side slope of the triangular section→m=12 Depth of flow→d=3 m…

Q: EGL * v2/29 초

A: To find : The difference in elevation (meter) of the channel floors. Given Data: The depth of…

Q: Water flows through a 2-m-wide rectangular channel with an average velocity of 5 m/s. If the flow is…

A: Given: The width of the rectangular channel is W=2 m. The average velocity of the water in the…

Q: A channel has a slope of 0.0004 m/m with n=0.015. It is expected that the channel will be able to…

A:

Q: What is the discharge of the pipe into reservoir B if a 1.2 m diameter concrete pipe 1800 m long…

A:

Q: How does the pressure change along the free surface in an open-channel flow?

A: Fluids are transported from one position to another using natural or constructed conveyance…

Q: Water is to be transported in a cast iron rectangular channel with a bottom width of 6 ft at a rate…

A: Given data: The bottom width of the channel is; b=6 ft. The flow rate of the water is; V˙=70 ft3s.…

Q: Water is flowing in an open channel as shown below at a depth of 2m and a velocity of 3m/sec. It…

A:

Q: Water flows in a triangular V-notch steel channel, with vertex angle of 60°, at a velocity of 1.2…

A:

Q: Water flows in a 9-m-wide rectangular open channel at a rate of 55 m3/s. If the flow depth is 2.4 m,…

A: Write the formula for Froude number in terms of flow depth, width, and flow rate for the given…

Q: Water, at 20°C, is flowing steadily in a 0.4-m- wide rectangular open channel, made of corrugated…

A: Here we haveb=0.4Q=0.2 m3/sy=0.15 mNow,          A=bxy=0.4 x 1.5 =0.06 m2Flow velocity…

Q: At what depth will water flow in a 4m wide rectangular channel if n= 0.018, S_0 = 0.0009 and Q =…

A: Given details: S0=0.0009n=0.018b=4 mQ=7 m3/sec Formula used: Q=1nAR2/3S01/2

Q: Consider water flow through a wide rectangular channel undergoing a hydraulic jump. Show that the…

A: Given data Flow depth before the jump, y1. Flow depth after the jump, y2. The expression of Froude…

Q: Determine the height of a rectangular weir of length 5m to be built across a rectangular channel.…

A:

Q: When is the flow in an open channel said to be uniform? Under what conditions will the flow in an…

A: Uniform flow: Uniform flow in the open channel is said when the depth of flow is constant at every…

Q: Water at 15°C is flowing uniformly in a 2-m-wide rectangular channel at an average velocity of 1.5…

A: Given data : Temperature (T) = 15oC width of rectangular channel (w) = 2 m average velocity (V) =…

Q: triangular open-channel

A: tan θ=HVθ=tan-134=36.87o ∠ABD=∠CBD=36.870 A=2 area of∆ABDA=2AD*BD2=AD*BDA=BDtan36.87*BD…

Q: Water flows in a rectangular open channel of width 5 m at a rate of 7.5 m3/s. The critical depth for…

A: The volume flow rate is given as,   V˙=7.5 m3/s   The width of rectangular open channel is given as,…

Q: Consider steady flow of water in a horizontal channel of rectangular cross section. If the flow is…

A: Flow in open channels are described with the help of a dimensionless number called as 'Froude Number…

Q: Determine the flow depth ina long length of lined trapezoid channel of base width 3

A:

Q: Water discharges into a rectangular horizontal channel from a sluice gate and undergoes a hydraulic…

A: Given,Velocity before jump,V1=9msDepth before jump,Y1=2 mThe froude number before…

Q: The flow rate of water in a 5-m-wide horizontal open channel is being measured with a 0.60-m-high…

A: Step-1  given Data               width b=5m                      pw=0.60m         water depth…

Q: The painted-steel channel of Fig. is designed, withoutthe barrier, for a flow rate of 6 m3/s at a…

A: Given: Q=6 m3/sh= 1 mb1=3 m (a) The hydraulic radius is calculated as:…

Q: A sharp crested suppressed weir under a head of 2.03 m is 3.50 m high and 2m long. Determine the…

A: Write the given data with suitable variables.

Q: A cast iron V-shaped water channel shown, has a bottom slope of 0.5°. For a flow depth of 0.75 m at…

A: Mannings Equation              Q=1.46×A×R23×S12n Calculate Cross-sectional area…

Q: A 3-ft-diameter semicircular channel made of unfinished concrete is to transport water to a distance…

A: Assume that the flow is steady and roughness is constant and also flow is uniform. The cross-section…

Q: A triangular open-channel (n=0.014) has a side slope of 2H:3V. The flow depth is 2m when the slope…

A: To find : The volumetric flow rate . Given :  The flow depth is d=2 m. The slope is s=0.002. The…

Q: Consider water flow in a rectangular open channel of height 2 m and width 5 m containing water of…

A:

Q: Consider water flow through two identical channels with square flow sections of 4 m × 4 m. Now the…

A: Given data d=4 mw=8 m

Q: The flow rate of water in a 10-m-wide horizontal channel is being measured using a 1.3-m-high…

A: To find out the weir head H=y1-Pw=3.4-1.3=2.1m   To find out the coefficient of the rectangular…

Q: Water at 20°C flows in a partially full 4-m-diameter circular channel at an average velocity of 2…

A: For the circular channel, let us assume that the flow of the channel is uniform. The radius of the…

Q: Consider the uniform flow of water in the triangular channel shown in the figure. The channel bed…

A: Write the expression of the normal depth. Q=1nAR2/3S

Q: Q1: what is the head above the crest of the notch (weir) shown in figure below, in order to make the…

A:

Q: The flow rate of water in a 6-m-wide rectangular channel is to be measured using a 1.3-m-high…

A: Given: The width of channel is w=6 m. The head above the weir crest is h=0.70 m.

Q: How does uniform flow differ from nonuniform flow in open channels? In what kind of channels is…

A: The flow characteristics of a fluid determine the flow as uniform and non-uniform. For uniform flow,…

Q: wide as shown. The upstream depth is 70 mm. The water surface rises 40 mm as it passes over a…

A: Solution -  Given data — width of channel -0.5 m

Q: The flow is occurring in a rectangular channel at a velocity of (571/500) m/sec and a depth of 0.2…

A: First, we will calculate the flow rate of water and use that value of Q in the relation given in the…

Q: Water flows uniformly in a rectangular channel with finished-concrete surfaces. The channel width is…

A: According to the given conditionCross sectional flow area is given asA=ybA=1.2×3A=3.6 m2and wetted…

Fluid Dynamics

The study of the flow of gases and liquids, usually in and around solid surfaces, is known as fluid dynamics in physics and engineering. Fluid dynamics, for example, can be used to evaluate the movement of air through an airplane wing or the surface of a vehicle. It can also be used in ship design to increase the speed at which ships pass through water.