- 2a2ao'2a-2aFigure P4.174.17. Find the product inertia Iyy for the beam section shown in Figure P4.17. Noticethat the centroid must be at O by symmetry.

Answered: y - 2a- 2a

Engineering

Mechanical Engineering

y - 2a- 2a

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter6: Beams And Cables

Section: Chapter Questions

Problem 6.18P: For the ladder in Prob. 6.17, find the internal force system acting on section 2, assuming that x <...

See similar textbooks

Similar questions

Consider a hollow drainage concrete cylinder of uniform mass density of 2,400kg/m^3 with length L=60m with R1 of 2.8m. Find its outer radius (R2) in m if the moment of inertia is 5, 067, 000kgm^-2 about its axis to symmetry is.
Consider the compact disc as a tick-walled cylinder has a mass of 16.0 g, and an outer diameter of 11.6 cm and inner diameter of 4.6 cm. Find the (a) moment of inertia of the compact disc about an axis passing through its center and (b) moment of inertia about an axis passing through its edge parallel to the previous axis.
A caravan weighs 28 kN. It has a wheel base of 2 m, track width 1m and height ofC.G. 300 mm above the ground level and lies midway between the front andrear axle. The engine flywheel rotates at 2950 rpm clockwise when viewed from thefront. The moment of inertia of the flywheel is 4 kg-m 2 and moment of inertia ofeach wheel is 3 kg-m 2 . Find the reactions between the wheels and the ground whenthe car takes a curve of 15 m radius towards right at 30 km/h, taking intoconsideration the gyroscopic and the centrifugal effects. Each wheel radius is 400 mm.
Find the centroidal moment of inertia Ix and Iy of the Z section of Fig 1. Let a = 3⁄4 in, b= 4 in and c = 21 in
Consider the shaded area shown in the figure. Suppose that a = 6 in. , b = 3 in. , and r = 2 in. Determine the moment of inertia for the shaded area about the y axis.
A loaded truck is transmitting 10 kN pressure on each wheel. The centre of gravity of the loaded truck is 1·2 m above the road level and the centre to centre distance of wheels is 2 m. Find the pressure exerted by the inner and outer wheels, when the truck is going round a curve of 440 m radius at 48 km.p.h.
A homogeneous circular disc with radius R = 5.04 m and thickness t = 12 x 10-3 m rotates around the z-axis (perpendicular to the disc, see figure). Calculate the moment of inertia of the disc around the z-axis (perpendicular to the disc and offset upwards a distance d = 1.78 m from the z-axis in the middle of the circle) if the density of the disc is 6.444 kg/m³.
Findwhere maximum bending moment occour solid mechanics solve
Solve this with complete free body diagram
The cone shown in the figure has a height h and a base radius P. The bulk density inside the cone depends on the distance from the z-axis as Y=A*r^3. Find the moment of inertia of this cone with respect to the E-axis parallel to the z-axis and at a distance d.Give your answer in terms of (R, h, d, M). (M here is the total mass of the cone)At the end of this problem, you will need to use the Parallel Axis Theorem. Hint is given in the 2.figure
A homogeneous circular disc with radius R = 5.04 m and thickness t = 10.1 x 10^−3 m rotates around the z-axis (perpendicular to the disc, see figure). A rectangular hole is cut from the centre of the disc with the base b = 4.725 m and the height h = 4.719 m. Calculate the mass moment of inertia of the disc around the z-axis if its density is 6.38 kg/m³.
Consider the image below: A horizontal beam of length 8 m is pinned at its left end so that it is free to rotate about that end. It has a nonuniform linear mass density given by λ(x) = 78 x (kg/m). Its right end is secured by a rope, the angle shown being 45 degrees. Calculate the magnitude of the tension in the rope, in N. (Please answer to the fourth decimal place - i.e 14.3225)