You are an engineering intern at a manufacturer of mechanical tools, your senior engineer asked you to evaluate the stresses on a newly-design utility hook, shown in Figure.6, to confirm it's not exceeding its yield strength. The hook dimensions are (d, Dị, L) = (20, 75, 250) mm. The task can be completed by calculating the stresses at the inner and outer surfaces of section A - A when the load is F = 4 kN. A D F D d

You are an engineering intern at a manufacturer of mechanical tools, your senior engineer asked you to evaluate the stresses on a newly-design utility hook, shown in Figure.6, to confirm it's not exceeding its yield strength. The hook dimensions are (d, Dị, L) = (20, 75, 250) mm. The task can be completed by calculating the stresses at the inner and outer surfaces of section A - A when the load is F = 4 kN. A D F D d

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.6P: The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular...

See similar textbooks

Similar questions

As seen in the figure, ABC rod with end-A fixed support pipe section has an outer diameter of 30 mm and an inner diameter of 24 mm. 50 N force at an angle of 30 ° with the y-axis at the free end C to the ABC rod is implemented. (a)Show and calculate the cross-sectional effects on the cross-section a a. (b) Calculate the stresses occurring at the H point of the ABC bar and calculate these stresses
Rigid bar ABC shown in the figure is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 5 mm, and it is supported by double-shear pin connections at B and D. The pin at bracket A is a single-shear connection. All pins are 6 mm in diameter. Assume a = 600 mm, b = 250 mm, h = 425 mm, P = 900 N, and θ = 55°. Determine the the shear stress in pin B. Express your answer in MPa rounded to the nearest hundredths.
STRENGTH OF MATERIALS (NO LONG EXPLANATION NEEDED) PLEASE WITH FBD! RATE WILL BE GIVEN For the given system below, rods A and B support the rigid bar, pinned at O, as it is subjected to load P = 40 kN. The rods are identical except for their lengths. Find the (a) stress in rod A if its cross-sectional is 300mm2 (b) If rod A elongates by 2mm, how much is the elongation of rod B?
For the beam shown, determine the support reactions and draw the stress diagrams. shear and bending moment. EI is constant. The rigth answer is: VA = 1.3 kN (↑); HA = 0 kN; MA = 4.40 kN.m (clockwise); VB = 51.20 kN (↑). I don't know how to get these results, please show how, step by step.
Please answer correctly, badly need it. Thank u godbless The internal shear force at a certain section of a steel beam is V= 8.8 kN. The beam cross-section shown in the figure has dimensions of b=141 mm, c=31 mm, d=63 mm, and t=6 mm. Determine: (a) the shear stress at point H. (b) the shear stress at point K. (c) the maximum horizontal shear stress in the cross-section. Break the cross-section into five rectangles, as shown. It is seen that the two labeled with a (1) are identical, and the two labeled with a (2) are identical. Find A1, the area of rectangles (1), and y1, the vertical distance from the bottom edge of the cross-section to the centroid of rectangles (1). Similarly, find A2, the area of rectangles (2), and y2, the vertical distance from the bottom edge of the cross-section to the centroid of rectangles (2). Then, find A3 and y3 for rectangle (3). A1= mm2 y1= mm A2= mm2 y2= mm A3= mm2 y3= mm Find y¯, the vertical…
A steel column of hollow circular cross section is supported on a circular, steel base plate and a concrete pedestal (see figure). The column has an outside diameter d = 250 mm and supports a load P - 750 kN. (a) If the allowable stress in the column is 55 MPa, what is the minimum required thickness? Based upon your result, select a thickness for the column, (Select a thickness that is an even integer, such as 10, 1 14,.. ., in units of millimeters.) (b) If the allowable bearing stress on the concrete pedestal is 15 MPa, what is the minimum required diameter D of the base plate if it is designed for the allowable load Pallow that the column with the selected thickness can support.
A 600 kg material is hung from the end of the horizontal bar BD as shown. Determine the stress on the rod AC if its diameter is 30 mm. Use 2 decimal places in every solved values. Pls include fbd.
STRENGTH OF MATERIALS. Please show the complete solutions. Rate will be given. Answer in 3 decimal places! The plate shown is fastened to the fixed member by eight 16-mm diameter rivets. Compute the polar moment of inertia, J. Determine the value of the loads P so that the maximum shearing stress in any rivet does not exceed 80 MPa. If P = 8200 N, what is the maximum and minimum shearing stress developed in the rivet.
Solve the following problems completely and neatly. Use 3 decimal places in all your computations except for strain and rho(5 decimal places). Input your answer in the text box provided in each number. Calculate the stress in the steel of the section in PART B in MPa.0
A steel plate 2.5 m x 1.3 m x 100 mm thick is to be hoisted by a steel cable sling as shown in the figure. Assume the steel weighs 77.3 kN/cu.m. Determine the bearing stress (MPa) in the steel plate the 10 mm diameter pins exert. The correct answer is 14.81. Show solution.
Rigid bar ABC shown in the figure is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 5 mm, and it is supported by double-shear pin connections at B and D. The pin at bracket A is a single-shear connection. All pins are 6 mm in diameter. Assume a = 600 mm, b = 250 mm, h = 425 mm, P = 900 N, and θ = 55°. Determine the the normal stress in rod (1). Express your answer in MPa rounded to the nearest hundredths.
Determine the average normal stress in each rod if T2=400∘F Calculate the new length of the aluminum segment.