You are freshly employed in the design department of Tesla Motors. Your new job requires you to model battery packs that are to be installed in the upcoming Tesla Roadster. The circuit below is a simple model for modelling terminal voltage, v(t), of a battery pack. Vbatt represents the ideal DC voltage that can be provided by battery. Ro models the dissipated losses. The parallel R1 - C1 pair models, what is known as "diffusion" in batteries i.e., when a battery is allowed to rest/charge, its voltage does not immediately increases or decreases, rather builds up or decays gradually, in a capacitive fashion. i1(t) R1 ilt) RO Vbatt C1 v(t) +1

You are freshly employed in the design department of Tesla Motors. Your new job requires you to model battery packs that are to be installed in the upcoming Tesla Roadster. The circuit below is a simple model for modelling terminal voltage, v(t), of a battery pack. Vbatt represents the ideal DC voltage that can be provided by battery. Ro models the dissipated losses. The parallel R1 - C1 pair models, what is known as "diffusion" in batteries i.e., when a battery is allowed to rest/charge, its voltage does not immediately increases or decreases, rather builds up or decays gradually, in a capacitive fashion. i1(t) R1 ilt) RO Vbatt C1 v(t) +1

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter33: Single-phase Motors

Section: Chapter Questions

Problem 1PA

See similar textbooks

Similar questions

It is common, in the analysis of electrical circuits, to determine voltage drops over resistors specific. If these are passed in circuits formed by independent sources, the principle of superposition is the technique used to solve this problem. He process that, for that, the current sources must be open-circuited and the voltage sources must be shorted. when doing this in the circuit presented below, determine a voltage drop across resistor R1.
Bioelectrical impedance analysis is a commercially available method used to estimate body fat percentage. The device applies a small potential between two parts of the patient's body and measures the current that flows through. With an estimate of the resistance individually of the muscle and fat between the two points, the composition of the tissue can be estimated. Assume that the muscle and fat tissue can be modeled as resistors in parallel. a) If a potential difference of 5 V is applied across the patient's arm, what is the potential drop across the patient's fat? b) If the measured resistance of the patient's arm is 750 Ω and the resistance of fat is 3 times that of muscle, what is the resistance of the muscle?
Q1) Conduct an evaluation on the practical applications of the concepts of electromagnetism and submit a written report which includes the following. a) Design a circuit which utilizes the concept of electromagnetism and submit a simulation circuit for the same (use simulation tool of your choice) b) Write down the selected values of the components used for example the values of resistors, transistor used, capacitors etc c) Obtain the output for the ciruit using any sinks like CRO, loud speakers etc. d) Discuss about the principles of electromagnetism used in the simulation I WANT QUESTION (D)
A field party in Antarctica is using a tent that has been equipped with a small outdoor gasoline generator. The generator’s Thevenin equivalent circuit has V T of 120 V DC and the equivalent resistance, R T , of 10 Ω. There are two resistive heaters inside the tent: R 1 = 10 Ω and R 2 = 120 Ω , that can be connected to the generator separately, in series, or in parallel. For the highest heater power output, how should the heaters be connected to the generator?
The weight of the car is 800 Kg The weight of each person is 75 Kg You may assume any missing parameters you need in the design appropriately (e.g., the rolling-resistance-power, air-resistance-power, the DC motor's parameters, ....etc)
Activity 5:An automated QA machine selects the product in an industry based on the perfection of color,weight, and length which are expressed by the variables C, W, and L, respectively. If a feature isperfect the machine takes input as ‘1’, ‘0’ otherwise. Based on the conditions, the machine decideswhether to reject (R) a product or not. Assume R = 1, if the weight is not perfect as well as if anyof the color or length is not perfect. Otherwise, R = 0.(5-a) Apply your knowledge of Boolean logic to form the truth table.(5-b) Use K-map to find the formula for the above scenario.(5-c) Draw the circuit diagram for the given scenario using the minimum number of practical gates.(5-d) Draw the circuit diagram for the given scenario using NAND gates only.(5-e) Use Multisim to verify your system.(5-f) What is the benefit of using digital circuits for the abovementioned scenario? Explain.
Activity 5:An automated QA machine selects the product in an industry based on the perfection of color,weight, and length which are expressed by the variables C, W, and L, respectively. If a feature isperfect the machine takes input as ‘1’, ‘0’ otherwise. Based on the conditions, the machine decideswhether to reject (R) a product or not. Assume R = 1, if the weight is not perfect as well as if anyof the color or length is not perfect. Otherwise, R = 0. Steps; 5-e) Use any circuit designer program to verify your system.(5-f) What is the benefit of using digital circuits for the abovementioned scenario? Explain.
A piece of electrical component inside a gaming laptop uses a source of electromotive force, resistor, and inductor. If the voltage, resistance, and inductance are 4sin4t volts, 2 ohms, and 1 henry, respectively, what is the current along the circuit after 2 seconds when the initial current applied to the circuit is 0.6 amperes? Assume Kirchhoff's Voltage Law applies which states that travelling around any loop/circuit, the gains and losses of voltage across the elements add up to zero. Do not round off intermediate steps. Round off the final answer to two decimal places.
Can you please elaborate on how these equations were reached via nodal analysis? and how exactly did the equation for I come to be and also what changed in the circuit so we can get these values? thank you. also if u can add in what cases i can use nodal analysis and what should i look for to know that i'm supposed to use it would be greatly appreciated, thank you!
Q2 \ The reproduction of cells in a bacterial colony is important for many environmental engineering applications such as wastewater treatments. The formula log(N) = log(N0) + t / T log(2) can be used to simulate this, where N0 is the original population, N is the population at time t, and T is the time it takes for the population to double. Using VB.net, write a program to calculate the value of T.
Please show the step-by-step result i need it ASAP please
10. This problem is all about Second-Order Circuits. Please provide an ANSWER and FREE BODY DIAGRAM. Thanks!