take Vs=333V round off to 3 decimal places You are presented with the following controlled rectifier configurations:TopologyConfigurationSupply phase voltageLoad resistanceLoad inductance(line to neutral)(Ohm)(Henry)Single phase half-waveSingle-phase bridgeThree-phase half-waveThree-phase bridgeSix-phase half-wave1Vs1002Vs1003Vs1004Vs100Vs100infiniteCalculate the load voltage for each configuration with its corresponding firing delay angle as stated in question10. Configuration 1;11. Configuration 2;12. Configuration 3;

Given: Consider the following controlled rectifier configuration: Vs=333 V To find: Calculate the…

You are presented with the following controlled rectifier configurations: Configuration Topology Supply phase voltage (line to neutral) Load resistance Load inductance (Ohm) (Henry) Single phase half-wave Single-phase bridge Vs 100 2 Vs 100 Vs Vs 3 Three-phase half-wave 100 Three-phase bridge Six-phase half-wave 4 100 Vs 100 infinite Calculate the load voltage for each configuration with its corresponding firing delay angle as stated in question 10. Configuration 1; 11. Configuration 2; 12. Configuration 3;

You are presented with the following controlled rectifier configurations: Configuration Topology Supply phase voltage (line to neutral) Load resistance Load inductance (Ohm) (Henry) Single phase half-wave Single-phase bridge Vs 100 2 Vs 100 Vs Vs 3 Three-phase half-wave 100 Three-phase bridge Six-phase half-wave 4 100 Vs 100 infinite Calculate the load voltage for each configuration with its corresponding firing delay angle as stated in question 10. Configuration 1; 11. Configuration 2; 12. Configuration 3;

EBK ELECTRICAL WIRING RESIDENTIAL

19th Edition

ISBN:9781337516549

Author:Simmons

Publisher:Simmons

Chapter19: Special-purpose Outlets-water Pump, Water Heater

Section19.2: Water Heater Branch Circuit

Problem 8R: For residential water heaters, the Consumer Product Safety Commission suggests a maximum temperature...

See similar textbooks

Similar questions

For residential water heaters, the Consumer Product Safety Commission suggests a maximum temperature setting of ___________ F (_____________ C). Some states have laws stating a maximum temperature setting of ____________ F (________________ C).
At what height are the telephone outlets in this residence mounted? Give measurement to center. _____
I need help with (d) . Thanks 1. Consider a half-wave rectifier circuit with a resistive load of 25 Ωand a 60 Hz ac source of 110V rms.(a) Determine v0(t) and i0(t)(b) Calculate the rms values of v0(t) and i0(t)(c) Calculate the average power delivered to the load(d) Repeat questions a , b, and c to the full wave rectifier of Figure below with R-load and thesame source and load parameters
Exe: The single-phase bridge rectifier has an RL Load and an ac source, with R = 10Ω andL = 10mH. The peak value of the source is Vm = 100V at 60 Hz. The expressions of voltage andcurrent outputs are:(a) Determine v0(t) and i0(t) with two ac terms (n=2 and 4)(b) Determine the power absorbed by the load.
3- One phase half wave controlled one rectifier feeding an ohmic load rectified voltage in the state of load current and voltage across a thyristor Source for trigger angle a = 120 ° two periods depending on the voltage Draw to scale along. Straightened of tension average the value of Calculate (U = 120 V, R = 10 ohm.
Three-phase half wave rectifier supply resistive load with DC power of 4 kW; the ammeter connected with D1 indicates 8 A r.m.s current, and the source frequency is 50 Hz Due to system inductance the average voltage drops to 96.2% of idealized value ( when the inductance is neglected). How much will the average and r.m.s voltage s be? The r.m.s phase current and average load current Is=? & Idc=? The secondary r.m.s voltage and transformer capacity Vs & KVA? The inductances causes the voltage drop Lc=? The diode forward current and maximum inverse voltage? Now, if the phase B is failed ( disconnected), how much with new dc voltage be in %..Vdc=….% ??
A full-wave rectifier is connected to a single-phase source and supplying an inductive load. For the sake of simplicity, you can assume that the ripple at the output current is negligible. Input specifications: The source is single-phase utility grid at 220 V and 50 Hz. Output specifications: The load resistance is 10 Ohm. Sketch the schematic of the system. Sketch the waveforms of the output voltage and current and the source voltage and current. Determine all the performance parameters.
Q1.Three-phase half wave rectifier supply resistive load with DC power of 4 kW; the ammeter connected with D1 indicates 8 A r.m.s current, and the source frequency is 50 Hz Due to system inductance the average voltage drops to 96.2% of idealized value ( when the inductance is neglected). How much will the average and r.m.s voltage s be? The r.m.s phase current and average load current Is=? & Idc=? The secondary r.m.s voltage and transformer capacity Vs & KVA? The inductances causes the voltage drop Lc=? The diode forward current and maximum inverse voltage? Now, if the phase B is failed ( disconnected), how much with new dc voltage be in %..Vdc=….% ??
FACTS: AC-DC converters take the AC power from wall outlets and convert it to unregulated DC. These power supplies include transformers that change the voltage of the AC that comes through wall outlets, rectifiers to save it from AC to DC and a filter that removes noise from the peaks and troths of the AC power waves.The DC-to-AC Converters are used to charge the batteries in the vehicles. These circuits are mainly used for driving low-power AC motors and are used in a solar power system. The DC to AC converters can be used in dc transmission lines for transmitting power to loads. QUESTION: What do you think is the main reason why we have AC power in our outlets instead of DC power? Explain your answer.
A single phase fully controlled bridge is operated with a resistive load R = 10 Ω, the input voltage to the bridge is 230 V. The firing angle is 60°. Determine, (i) Average load voltage, (ii) Average and rms load current, (iv) Average output power, (iii) Form factor and ripple factor, (v) Rectifier efficiency, and (vi) SCR ratings
Design a full wave rectifier with capacitor filter, using a centrally tapped Trafo to supply a load of 100Ω. Specify all components: Trafo, rectifier diodes, capacitor filter and power dissipated in the load. The ripple should not exceed 3.0Vpp. THE load voltage should be 30 VDC. (0.5) Draw the electrical circuit of the rectifier correctly. Watch out for the units!
Determine the DC currents (IB, IC and IE) and dc junction voltages (VBE, VCE and VCB) Use the following values: VBB = 4V RB = 5 kΩ RC = 188 Ω VCC = 23 V βDC = 73