You have a choice between four types of candidate near-inert bioceramic for use in the manufacture of a femoral head component from a number of different suppliers. Which one should you choose given the information in the table below? Bioceramic Formulation: Density (g/cm³) Grain Size (μm) Flexural Strength (MPa) Hardness (HV) Fracture Toughness Kic (MPa.m-¹/²) Select one: O a. Material Delta O b. Material Omicron O c. Material Alpha O d. Material Beta Alpha 3.86 <4.5 450 1800 3.5 Beta 3.98 <2.0 580 2000 5 Omicron 6.08 <0.5 1050 1250 9 Delta 4.36 <1.5 1150 1975 8.5

You have a choice between four types of candidate near-inert bioceramic for use in the manufacture of a femoral head component from a number of different suppliers. Which one should you choose given the information in the table below? Bioceramic Formulation: Density (g/cm³) Grain Size (μm) Flexural Strength (MPa) Hardness (HV) Fracture Toughness Kic (MPa.m-¹/²) Select one: O a. Material Delta O b. Material Omicron O c. Material Alpha O d. Material Beta Alpha 3.86 <4.5 450 1800 3.5 Beta 3.98 <2.0 580 2000 5 Omicron 6.08 <0.5 1050 1250 9 Delta 4.36 <1.5 1150 1975 8.5

Precision Machining Technology (MindTap Course List)

2nd Edition

ISBN:9781285444543

Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Publisher:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Chapter2: Measurement, Materials, And Safety

Section2.6: Metal Composition And Classification

Problem 6RQ: Small particles of________ alloys are flammable.

See similar textbooks

Similar questions

1. Choose the material that is brittle, a poor thermal conductor, a good thermal insulator, and can withstand high temperatures. a. Ceramics b. Composites c. Polymers d. Metals 2. Choose the substance with the greatest surface tension. a. C9H20 b. C12H26 c. C6H14 d. C24H50 3. Condensation polymers A. Are deposited in molds by condensing vapors B. Also release a small molecule such as water when they are formed C. Usually are made from monomers containing one or more C=C bonds D. None of the Above
Which of the following is FALSE regarding the continuum assumption of fluids? Select one: a. Uncertainties within the molecular properties of the fluid will be neglected b. Limit concepts can be applied on fluids c. Fluids with same composition may have different properties d. The fluid will be analyzed in the macroscopic level Which of the following does NOT describe a difference between liquids and gases? Select one: a. Liquids form a free surface while gases do not b. Liquids have lower bulk modulus of elasticity than gases c. Specific gravities of liquids are higher than gases d. Viscosity of liquids decreases as temperature increases while on gases, viscosity increases with temperature
A tentative rule was given about tipping in Testing Experiment Table 8.4, where if a vertical line passing through the object's center of mass is within the object's area of support the object does not tip. According to the rule, the full box of crackers in the following experiment, which has a width of 13 cm and a height of 20 cm, was seen to tip at an angle of: θc=tan−1(13 cm/20 cm)=33∘θ According to the rule, at what angle will a box with the left half filled with crackers begin to tip? Assume the box is light-weight and that the contents remain in the configuration in
In analysis of an aluminum-zinc alloy, the mass of gelatin capsule is 0.1192g, mass of alloy is 0.2634g, mass of empty Beaker is 168.2449, mass of Beaker + Water is 272.5682g, the temperature of water is 22 degrees Celsius, the vapor pressure of water from table 1 is 19.827 mm Hg, Calculate mass of alloy sample.
Suppose we got the following data during a test of a 2- stroke engine in which gas is usedas a fuel:Diameter of the piston = 149 mmStroke length = 179 mmClearance volume = 0.88 literrpm of the engine = 302Indicated mean effective pressure = 6.0 barGas consumption = 6.0 m3/hCalorific value of the gas (fuel) = 16990 kJ/m3Make a clear sketch the geometry of this engine using the data and determine thefollowing:i. Indicated power developed by the engine in watt.ii. Air Standard Efficiencyiii. Indicated thermal efficiency of the engine.
S-curve model of diffusion: (true/false) and reasoning a. k = 0, the rate of diffusion is instantaneous? b. fixed k ≥ 0, the carrying capacity is determined only by the ratio of a and b? c. fixed k ≥ 0, the rate of diffusion is determined only by the ratio of a and b?
I mix two fluids together, and I use the same mass of each fluid. They are completely miscible; in fact, the two chemicals are isomers. What is the composition of the mixture on a molar basis? Give a numerical answer and a written explanation of how you arrived at it, but do not use any equations.
Case 1: Material system without density and viscosity differences Though unlikely in real life, in this case, we assume that all of the material in the homogenizer is of the same density and viscosity. Thus, only one set of material parameters are mentioned (density, ρ; dynamic viscosity, μ). The important parameters are listed as follows: Target quantity : Mixing time, θ Geometric parameters : Stirrer diameter, d Material parameters : Density, ρ Dynamic viscosity, μ Process-related parameters : Stirrer speed, n 1.1) Write out the relevance list for Case 1. 1.2) Generate the pi-set for this case. 1.3) Write out the appropriate pi (π) numbers from the generated pi-set. 1.4) Identify the established dimensionless numbers from the derived pi (π) numbers. 1.5) Write the possible relationship of the dimensionless numbers for Case 1.
Consider the following samples of gases at the same temperature. REFER IMAGE Arrange each of these samples in order from lowest to highest:a. pressureb. average kinetic energyc. densityd. root mean square velocityNote: Some samples of gases may have equal values for these attributes. Assume the larger containers have a volume twice the volume of the smaller containers, and assume the mass of an argon atom is twice the mass of a neon atom.
Refer to the Worksheet shown, set up to calculate the displacement of a spring. Hooke's law states that the force (F, in newtons) applied to a spring is equal to the stiffness of the spring (k, in newtons per meter) times the displacement {x, in meters): F= kx. ;Chapter 10, Problem 161CA, Refer to the Worksheet shown, set up to calculate the displacement of a spring. Hooke's law states Cell A3 contains a data validation list of springs. The stiffness (cell 83) and maximum displacement (cell C3) values are found using a VLOOKUP function linked to the table shown at the right side of the worksheet. These data are then used to determine the displacement of the spring at various mass values. A warning is issued if the displacement determined is greater than the maximum displacement for the spring. Use this information to determine the answers to the following questions. Write the expression, in Excel notation, that you would type into cell 86 to determine the displacement of the spring.…
MECT361 Mechatronics Components and Instrumentation Please solve the problem in keupord 0.Consider the Material Selection Design Problem for the FRAME of a Human Powered Road Vehicle. Define the selection criteria, assign weights (importance), and evaluate the following alternatives based on COST, WEIGHT, STRENGTH, AVAILABILITY, MANUFACTURABILITY, ASSEMBLY, TEST & MAINTENANCE, ENVIRONMENT & SUSTAINABILITY, SAFETY & RELIABILITY: a.Steel b.Aluminum c. Titanium d.Composite- CFRP
The bulk modulus of a material, as a meaningful physical property, is applicable to which of the following? Choose A. Only liquid B. Only gas C. Solids, liquids and gases D. Only solid