You have been asked to investigate the loading effects on an alternator supplying a load and also charging a car battery at the same time. The output of the alternator has been rectified to smooth dc, and the circuit is shown below. I Battery 1 15V 0.80 Load 120 G Rectifier output 16V 2.89 Using Kirchhoff analysis, determine the initial current in each section along with its direction and the potential difference across the load.

You have been asked to investigate the loading effects on an alternator supplying a load and also charging a car battery at the same time. The output of the alternator has been rectified to smooth dc, and the circuit is shown below. I Battery 1 15V 0.80 Load 120 G Rectifier output 16V 2.89 Using Kirchhoff analysis, determine the initial current in each section along with its direction and the potential difference across the load.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.3P: The instantaneous voltage across a circuit element is v(t)=400sin(t+30)volts, and the instantaneous...

See similar textbooks

Similar questions

Let a series RLC network be connected to a source voltage V, drawing a current I. (a) In terms of the load impedance Z=ZZ, find expressions for P and Q, from complex power considerations. (b) Express p(t) in terms of P and Q, by choosing i(t)=2Icost. (c) For the case of Z=R+jL+1/jC, interpret the result of part (b) in terms of P,QL, and Qc. In particular, if 2LC=1, when the inductive and capacitive reactances cancel, comment on what happens.
The instantaneous voltage across a circuit element is v(t)=400sin(t+30)volts, and the instantaneous current entering the positive terminal of the circuit element is i(t)=100cos(t+10)A. For both the current and voltage, determine (a) the maximum value, (b) the rms value, and (C) the phasor expression, using cos(t) as the reference.
Consider two interconnected voltage sources connected by a line of impedance Z=jX, as shown in Figure 2.27. (a) Obtain expressions for P12 and Q12. (b) Determine the maximum power transfer and the condition for it to
The real power delivered by a source to two impedances, Z1=4+j5 and Z2=10 connected in parallel, is 1000 W. Determine (a) the real power absorbed by each of the impedances and (b) the source current.
Under balanced operating conditions, consider the three-phase complex power delivered by the three-phase source to the three-phase load. Match the following expressions, those on the left to those on the right. (i) Realpower, P3 (a) (3VLLIL)VA (ii) Reactive power, Q3 (b) (3VLLILsin)var (iii) Total apparent power, S3 (c) (3VLLILcos)W (iv) Complex power, S3 (d) P3+jQ3 Note that VLL is the rms line-to-line voltage, IL is the rms line current, and is the power-factor angle.
Is the power factor in Question 6 a leading or lagging power factor? Explain your answer.
How many different load groups are there in power plants? Explain by drawing on a power-time curve.
In the circuit given on the side Ra=Rb=Rc=Basic frequency of 13 Ohm loadsit is powered by an AC voltage of f= 60 Hz. Power derived from the sourceits value was measured as Pk=9372.12 Watts. Each switchingthe element is triggered in such a way that it will be at 180 degrees.The DC bus voltage (E=?) and the effective value of the ic phase current(ic rms=?) calculate.
Two generating stations A and B have the capacities 500MW and 800MW respectively are interconnected by a short line. The percentage speed regulations from no load to full load of the two stations are 2 and 3 respectively. Find the power generation at each station and power transfer through the line if the load on bus of each station in 200MW.
CAN YOU EXPLAIN THE OPERATIONS IN SENTENCES? For the maximum average power transfer in the circuit shown in Figure 2, use the impedance ZLand ZLFind the value of the maximum average power transferred to ?
What are ‘load curves’ and ‘load duration curves’? Discuss their utility in the economics of generation.
Given that a nonzero AC voltage source is applied, what can you say about whether the power, reactive and complex power are positive, negative, or zero for a load with a lagging Power Factor. Repeat your analysis for this load when connected in parallel with a pure capacitor. Consider all cases and justify your answer(s).