You pull on a crate using a rope as image, except the rope is at an angle of 20.0 ∘ above the horizontal. The weight of the crate is 325 N, and the coefficient of kinetic friction between the crate and the floor is 0.230. What must be the tension in the rope to make the crate move at a constant velocity? What is the normal force that the floor exerts on the crate?

You pull on a crate using a rope as image, except the rope is at an angle of 20.0 ∘ above the horizontal. The weight of the crate is 325 N, and the coefficient of kinetic friction between the crate and the floor is 0.230. What must be the tension in the rope to make the crate move at a constant velocity? What is the normal force that the floor exerts on the crate?

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.78P: The figure shows a steel bar being processed by a rolling mill. Given that P=80kN and r =0.016,...

See similar textbooks

Similar questions

Two blocks of mass 50 kg and 40 kg are connected by a light inextensible string as shown in Fig. Find, from first principles, the acceleration of the system and tensions in the cable. Take Friction coefficient = 0.3
You construct a version of the cart and bucket, but with a slope whose angle can be adjusted. You use a cart of mass 167 kg and a bucket of mass 57.0 kg. The cable has negligible mass, and there is no friction. What must be the angle of the slope so that the cart moves downhill at a constant speed and the bucket moves upward at the same constant speed? With this choice of angle, what will be the tension in the cable?
Q5 A pull of 20 N at 30 ° to the horizontal is necessary to move a block of wood on a horizontal table . If the coefficient of friction between the bodies in contact is 0.25 , what is the weight of the block ?
An electric motor is accelerating a 250 kg load with acceleration of 1.2 m/s? througha gear box as shown Figure Q1(b). The rope that carries the load and spiral spring are encircled on a pulley with diameter 1.2m. Gear box ratio is 0. 1 and gear box efficiency is 100%, while gear box equivalent moment inertia is 5.55 km?. Neglect friction effect in this drive system and assume spiral spring force is X newtonCalculate the torque of the motor needed to bring up the load with acceleration1.2 m/s?.
A 200-kg log is pulled up a ramp by means of a rope that is parallel to the surface of the ramp. The ramp is inclined at 34.5° with respect to the horizontal. The coefficient of kinetic friction between the log and the ramp is 0.870, and the log has an acceleration of 0.750 m/s2. Find the tension in the rope.
A ring of mass m is attached to the spring and slides over the rod. Unextended length of the spring l0 and the spring coefficient is k. When the collar is at point C, it is released and between the collar and bar Since the coefficient of friction is μk; a) Find the velocity of the ring at points A and B using the Work-Energy method. b) Find the normal forces acting on the collar at points A and B.
A V-belt drives a pulley at a speed of 1440 m/min. The coefficient of friction between belt andpulley is 0.3, semi V-groove angle is 22.5o and angle of contact of belt with the pulley is 160o. Ifthe mass of the belt is 0.45 kg/m and if permissible pull in the belt is 800 N. Calculate the power.Consider the centrifugal tension in the belt.
You are designing a high speed elevator for a new skyscraper. The elevator will has a mass limit of 2400 kg. For passenger comfort, you choose the maximum ascent speed to be 18.0 m/s, the maximum descent speed to be 10.0 m/s, and the maximum acceleration magnitude to be 4.60 m/s squared. Ignore friction. 14. What is the minimum time it will take the elevator to ascend from the lobby to the observation deck, a vertical displacement of 640 m?
b. The skateboarder in Figure is coasting down a ramp of 300 degree,weight of the person is575 N and the frictional force is 125 N. Find the normal force from the surface.Also, determine the net work done by the three forces when the person coastingdown for a distance of 9.0 m.
A block of mass M1 resting on an inclined plane is connected by a string and pulleys to another block of mass M2 as shown in Fig. Find the tension in the string and acceleration of the blocks. Assume the coefficient of friction between the blocks M1 and the plane to be 0.2. M1=1500N , M2=1000N . Angle of inclined glane = 45 degrees
In order to burgle a local McDonald's, the Hamburglar must climb onto the roof. To do this, a ladder of length 3.31 m and mass 21.2 kg is placed leaning against a vertical wall, as shown in the image below. There is negligible friction between the ladder and the wall, but the same is not true for the ladder and the ground: us ≠ 0 between those two surfaces. Even with that friction, the ladder will start slipping if the angle ø ladder makes relative to the ground is less than 71.0°. Assuming the ladder is uniform (so that its center of gravity is located at its geometric center), what must be the maximum static frictional force (in N) that exists between the bottom of the ladder and the ground? Explain how you solved the problem involving a ladder leaning against a wall. Be sure to state what your known and unknown quantities are, what concepts were applied, and what equations were used!
A Volkswagen Bug weighing 3,045 lb is design with a wheelbase of 100.1 in has a center ofgravity that is 17 in above the pavement and 25 in behind the front axle. If the car is on aroadway with packed snow or ice, what is the maximum tractive effort that can be developed ifthe car is (a) front-wheel drive or (b) rear-wheel drive?