Your Network Administrator has contacted you to assist in examining a workstation that has been showing network fluctuations time and again. It seems that someone spilled some hot water over the Ethernet ports. Which of the following addresses will you choose to check the functionality of the Ethernet card without worrying about corrupted hardware and to ensure that the workstation's TCP/IP services are running? ping -a 8.8.8.8 ping -a 0.0.0.0 ping 127.0.0.1 ping 192.168.1.1

Your Network Administrator has contacted you to assist in examining a workstation that has been showing network fluctuations time and again. It seems that someone spilled some hot water over the Ethernet ports. Which of the following addresses will you choose to check the functionality of the Ethernet card without worrying about corrupted hardware and to ensure that the workstation's TCP/IP services are running? ping -a 8.8.8.8 ping -a 0.0.0.0 ping 127.0.0.1 ping 192.168.1.1

A+ Guide To It Technical Support

10th Edition

ISBN:9780357108291

Author:ANDREWS, Jean.

Publisher:ANDREWS, Jean.

Chapter7: Setting Up A Local Network

Section: Chapter Questions

Problem 4TC

See similar textbooks

Similar questions

Arriving at your university room, you plug into the wired Ethernet jack for the first time. The network admin has a record of your MAC address and your machine can join the network without further action on your part. Assume: Your laptop's Ethernet address is 0a:0b:0c:0d:0e:0f, DHCP server address is 131.111.7.3, your IPv4 address will be 131.111.7.121, the gateway's IP address is 131.111.7.1, and Ethernet address is 00:01:02:03:04:05, the network subnet mask is 255.255.255.0.Write the series of protocol/packet exchanges that occur on the wired Ethernet link, up until you can send a single packet to 128.232.0.20. You do not need to describe packets after this packet has left the link. Include ARP and DHCP
I ran the ipconfig command on my computer and it reports an IP address 169.254.75.10 on the ethernet interface. Which device assigned this IP address to this interface?
Your network has a device with an Ethernet NIC that is set up with a static IPv4 address. Which two of the following IPv4 settings will be shown in the PC's IPv4 configuration? Traceroute address server DHCP Server address IP address of the PC DNS server address
You as a network administrator want to protect the network from unauthorized traffic, and for this reason, you decide to change the native VLAN to an unused VLAN so that the untagged traffic is essentially directed toward a dead-end. Which of the following commands will you use to do this on a Cisco switch? a. set native-vlan-id b. set port-mode trunk c. switchport trunk native vlan d. ip dhcp snooping
You plug a host into a switch port and the host receives an IP address but the user can’t get to the services it needs. What is probably the problem?
Which file would you modify to permanently change the TCP/IP address of the firstwired NIC on a Fedora 20 system?a. /etc/sysconfig/network-scripts/ifcfg-eth1b. /etc/sysconfig/network-scripts/ifcfg-eth0c. /etc/sysconfig/network-scripts/ipcfg-eth0d. /etc/sysconfig/network-scripts/ipcfg-eth1
From your laptop, you need to remote into a switch to make some configuration changes.Which Transport layer protocol and TCP/IP port should you open in Windows Firewall tomake this work using Telnet?a. UDP, port 23b. TCP, port 23c. UDP, port 22d. TCP, port 22e. UDP, port 21
Your network has a static IPv4-configured Ethernet NIC device. Which two IPv4 parameters below will be included in the PC's IPv4 setup? Traceroute server's IP. PC-private DHCP server address DNS server address
The scenario includes one DHCP server in an Active Directory domain. The server is configured to provide IP addresses to DHCP clients on two different subnets. The subnets are separated by a router that has DHCP Forwarding enabled. In this scenario, you use ten of the excluded IP addresses to configure servers and other devices with static IP addresses and five additional IP addresses are left available for static configuration of new devices that you might want to add in the future. Write up the Powershell script for the following according to scenario IP configuration: Installing DHCP role (DHCP1) Creating DHCP security group (your Arid Number) in DHCP1 Note: Security Group should create with your arid number. Authorizing the DHCP1server in DC1 How to getClient4 adapter hardware information Disable and Enable a Network Adapter of Client4
You have a server with two NICs, each attached to a different IP network. You’re having problems communicating with devices on remote networks that send packets to one of the interfaces. The server receives the packets fine, but the server’s replies never reach the intended destination network. Replies to packets that come in through the other interface seem to reach their destination without any problems. What can you do that will most likely solve the problem? a. Configure a second default gateway on the interface exhibiting problems. b. Change the default gateway to use the router that’s on the network of the interface exhibiting problems. c. Use the route command to add routes to the networks that aren’t receiving replies. d. Replace the NIC that’s having problems replying to packets.