BuyFind*arrow_forward*

6th Edition

KASSIMALI + 1 other

Publisher: Cengage,

ISBN: 9781337630931

Chapter 5, Problem 63P

Textbook Problem

135 views

5.57 through 5.71 Draw the shear, bending moment, and axial force diagrams and the qualitative deflected shape for the frame shown.

To determine

Plot the shear diagram, bending moment diagram, axial force diagram, and the qualitative deflected shape of the frame.

Write the condition for static instability, determinacy and indeterminacy of plane frames as follows:

Here, number of members is *m*, number of external reactions is *r*, the number of joints is *j*, and the number of elastic hinges is

Find the degree of static indeterminacy (*i*) using the equation;

Refer to the Figure in the question;

The number of members (*m*) is 2.

The number of external reactions (*r*) is 3.

The number of joints (*j*) is 3.

The number of elastic hinges

Substitute the values in Equation (2).

Show the free-body diagram of the entire frame as in Figure 1.

Refer Figure 1,

Find the vertical reaction at point *A* by resolving the vertical component of forces.

Find the horizontal reaction at point *A* by resolving the horizontal component of forces.

Find the moment at point *A* by taking moment about point *A*.

Show the free-body diagram of the members and joints of the entire frame as in Figure 2.

Consider point *A*:

Resolve the vertical component of forces.

Resolve the horizontal component of forces

Structural Analysis

Show all chapter solutions

Ch. 5 - Determine the axial forces, shears, and bending...Ch. 5 - Determine the axial forces, shears, and bending...Ch. 5 - Determine the axial forces, shears, and bending...Ch. 5 - Determine the axial forces, shears, and bending...Ch. 5 - Determine the axial forces, shears, and bending...Ch. 5 - Determine the axial forces, shears, and bending...Ch. 5 - Determine the axial forces, shears, and bending...Ch. 5 - Determine the axial forces, shears, and bending...Ch. 5 - Determine the axial forces, shears, and bending...Ch. 5 - Determine the axial forces, shears, and bending...

Ch. 5 - 5.1 through 5.11 Determine the axial forces,...Ch. 5 - Determine the equations for shear and bending...Ch. 5 - Determine the equations for shear and bending...Ch. 5 - Determine the equations for shear and bending...Ch. 5 - Determine the equations for shear and bending...Ch. 5 - Determine the equations for shear and bending...Ch. 5 - Determine the equations for shear and bending...Ch. 5 - Determine the equations for shear and bending...Ch. 5 - 5.12 through 5.28 Determine the equations for...Ch. 5 - 5.12 through 5.28 Determine the equations for...Ch. 5 - 5.12 through 5.28 Determine the equations for...Ch. 5 - 5.12 through 5.28 Determine the equations for...Ch. 5 - 5.12 through 5.28 Determine the equations for...Ch. 5 - 5.12 through 5.28 Determine the equations for...Ch. 5 - 5.12 through 5.28 Determine the equations for...Ch. 5 - 5.12 through 5.28 Determine the equations for...Ch. 5 - 5.12 through 5.28 Determine the equations for...Ch. 5 - 5.12 through 5.28 Determine the equations for...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - Draw the shear and bending moment diagrams for the...Ch. 5 - For the beam shown: (a) determine the distance a...Ch. 5 - For the beam shown: (a) determine the distance a...Ch. 5 - 5.55 and 5.56 Classify each of the plane frames...Ch. 5 - 5.55 and 5.56 Classify each of the plane frames...Ch. 5 - Draw the shear, bending moment, and axial force...Ch. 5 - Draw the shear, bending moment, and axial force...Ch. 5 - Draw the shear, bending moment, and axial force...Ch. 5 - Draw the shear, bending moment, and axial force...Ch. 5 - Draw the shear, bending moment, and axial force...Ch. 5 - Draw the shear, bending moment, and axial force...Ch. 5 - 5.57 through 5.71 Draw the shear, bending moment,...Ch. 5 - 5.57 through 5.71 Draw the shear, bending moment,...Ch. 5 - 5.57 through 5.71 Draw the shear, bending moment,...Ch. 5 - 5.57 through 5.71 Draw the shear, bending moment,...Ch. 5 - 5.57 through 5.71 Draw the shear, bending moment,...Ch. 5 - 5.57 through 5.71 Draw the shear, bending moment,...Ch. 5 - 5.57 through 5.71 Draw the shear, bending moment,...Ch. 5 - 5.57 through 5.71 Draw the shear, bending moment,...Ch. 5 - 5.57 through 5.71 Draw the shear, bending moment,...

Find more solutions based on key concepts

Show solutions using Figure 5-27, what is the advantage of the suspended type magnet over the other two types of magnets?

Solid Waste Engineering

Repeat Problem 2.11 with the following data. 2.11 The grain-size characteristics of a soil are given in the fol...

Principles of Geotechnical Engineering (MindTap Course List)

Following are the results of a sieve analysis: a. Determine the percent finer than each sieve size and plot a g...

Fundamentals of Geotechnical Engineering (MindTap Course List)

Check the adequacy of the weld. The 20-kip load is a service lead, with a live load-to-dead load ratio of 2.0. ...

Steel Design (Activate Learning with these NEW titles from Engineering!)

For Problem 19.27, determine the probability (assuming normal distribution) that a car would need engine mainte...

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

Which information attributes are seldom or never applied to software elements?

Management Of Information Security

A brass cube of 48 mm on each edge is comp ressed in two perpendicular directions by forces P = 160 kN (see fig...

Mechanics of Materials (MindTap Course List)

Describe the functions of a human resource MIS.

Fundamentals of Information Systems

Accounting for Treasury Stock Paris Corporation provides travel planning services for large corporations across...

Cornerstones of Financial Accounting

Define the terms, broadband, bandwidth, and latency.

Enhanced Discovering Computers 2017 (Shelly Cashman Series) (MindTap Course List)

What is an information system? What is the role of feedback in a system?

Principles of Information Systems (MindTap Course List)

Why are bimetal strips often formed into a spiral?

Electric Motor Control

Using a Web browser, go to www.eff.org. What are the current top concerns of this organization?

Principles of Information Security (MindTap Course List)

Write a query to display the book number, title, subject, average cost of books within that subject, and the di...

Database Systems: Design, Implementation, & Management

Construct the shear force and bending moment diagrams for the beam shown by the area method. Neglect the weight...

International Edition---engineering Mechanics: Statics, 4th Edition

Which rows are included in a left outer join? What clause can you use to perform a left outer join in SQL?

A Guide to SQL

The basic safety rule when working with electricity is to ______

EBK ELECTRICAL WIRING RESIDENTIAL

What are the functions of an isolation/dump valve?

Automotive Technology

Write the query that lists the average age of your customers. (Assume that the CUSTOMER table has been modified...

Database Systems: Design, Implementation, & Management

A______ can be used to measure cutting fluid concentrations.

Precision Machining Technology (MindTap Course List)

What method does a GSM network use to separate data on a channel? a. SIM b. CDMA c. TDMA d. TDM

Network+ Guide to Networks (MindTap Course List)

Identify and briefly describe five common fact-finding methods.

Systems Analysis and Design (Shelly Cashman Series) (MindTap Course List)

Other than selling more cars, what potential benefits do connected-car technologies offer auto makers such as B...

Fundamentals of Information Systems

Technician A uses sandpaper to remove carbon deposits from turbocharger wastegate parts. Technician B scrapes o...

Automotive Technology: A Systems Approach (MindTap Course List)

A car weighs 3000 lbm and is travelling 60 mph when it has to make an emergency stop. The car comes to a stop 5...

Fundamentals of Chemical Engineering Thermodynamics (MindTap Course List)

If your motherboard supports ECC DDR3 memory, can you substitute non-ECC DDR3 memory?

A+ Guide to Hardware (Standalone Book) (MindTap Course List)

Describe the relation between voltage and amperage for welding current.

Welding: Principles and Applications (MindTap Course List)