You are an electrician working in an industrial plant. A circuit contains eight incandescent lamps connected in series across 480 volts. One lamp has burned out, and you must determine which one is defective. You have available a voltmeter, ammeter, and ohmmeter Which meter would you use to determine which lamp is defective in the shortest possible time? Explain how you would use this meter and why

You are an electrician working in an industrial plant. A circuit contains eight incandescent lamps connected in series across 480 volts. One lamp has burned out, and you must determine which one is defective. You have available a voltmeter, ammeter, and ohmmeter Which meter would you use to determine which lamp is defective in the shortest possible time? Explain how you would use this meter and why

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter2: Electrical Quantities And Ohm’s Law

Section: Chapter Questions

Problem 3PA: You are an electrician installing the wiring in a new home. The homeowner desires that a ceiling fan...

See similar textbooks

Similar questions

You are an electrician installing the wiring in a new home. The homeowner desires that a ceiling fan with light kits be installed in five different rooms. Each fan contains a light kit that can accommodate four 60-watt lamps. Each fan motor draws a current of 1.8 amperes when operated on high speed. It is assumed that each fan can operate more than three hours at a time and therefore must be considered a continuous-duty device. The fans are to be connected to a 15-ampere circuit. Because the devices are continuous-duty, the circuit current must be limited to 80% of the continuous connected load. How many fans can be connected to a single 15-ampere circuit? How many circuits will be required to supply power to all five fans?
You are a journeyman electrician working in a large office building. The fluorescent lighting system is operated at 277 V. You have been instructed to replace the existing light ballasts with a new electronic type that is more efficient. The manufacturer of the ballast states that the maximum peak operating voltage for the ballast is 350 V. Will the new electronic ballast operate on the buildings lighting system without harm?
3. You are an electrician. You have been asked by a homeowner to install a lighted mirror in a bathroom. The mirror contains eight 40-watt lamps. Upon checking the service panel you discover that the bathroom circuit is connected to a single 120-volt, 20-ampere circuit breaker. At present, the circuit supplies power to an electric wall heater rated at 1000 watts, a ceiling fan with a light kit, and a light fixture over the mirror. The fan motor has a full-load current draw of 3.2 amperess and the light kit contains three 60-watt lamps. The light fixture presently installed over the mirror contains four 60-watt lamps. The homeowner asked whether the present light fixture over the mirror can be replaced by the lighted mirror. Assuming all loads are continuous, can the present circuit supply the power needed to operate all the loads without overloading the circuit?
Basic Electrical Engineering A homeowner is installing a swimming pool. You have been asked to install a circuit to operate a 600-watt underwater light and a circuiting pump. The motor nameplate reveals that the pump has a current draw of 8.5 amperes. The devices are considered a continuous duty. Can the power to operate both of these devices be supplied by a single 20-ampere circuit? The voltage source is 220 V.
WHICH OF THE ELECTRICAL SWITCHES (USING JUST ONE UNIT ONLY) CAN YOU USE TO PUT ON AND OFF ALTERNATELY TWO BULBS? YOU MAY EXPLAIN BRIEFLY OR DRAW A SCHEMATIC OR WIRING DIAGRAM.
The power to a 25-watt lamp is being measured with a voltmeter and an ammeter. The voltmeter has a resistance of 14,160 ohms. The meter is connected directly across the lamp terminals. When the ammeter reads 0.206 ampere, the voltmeter reads 119 volts. 1. What is the true power of the lamp? 2, What percentage of error is introduced if the instrument power is neglected?
A homeowner is installing a swimming pool. You have been asked to install a circuit to operate a 600-watt underwater light and a circulating pump. The motor nameplate reveals that the pumph hasa current draw of 8.5 amperes. The devices are considered continuous duty. Can the power to operate both of these devices be supplied by a single 20-ampere circuit?
A garden hose is used to fill the pool. Water comes out of the hose at a rate of 10.5 gallons per minute. How much time, to the nearest hour, will it take to fill the pool 6 inches from the top? [1 ft3 = 7.48 gallons]
A blow-dryer and a vacuum cleaner each operate with a voltage of 120 V. The current rating of the blow-dryer is 9.2 A, while that of the vacuum cleaner is 4.4 A. Determine the power consumed by (a) the blow-dryer and (b) the vacuum cleaner. (c) Determine the ratio of the energy used by the blow-dryer in 10 minutes to the energy used by the vacuum cleaner in 59 minutes.
How do you connect an ammeter to determine the current in a resistor? How do you connect a voltmeter to determine the voltage in a resistor?
An electrician charges $425.00 for a wiring job. The cost of materials amounts to 62% of the total cost. Find the amount'of money that the electrician receives for labor
Older Homes have fuses instead of cicuit breakers. The fuse will blow, breaking the cicuit, if more then a certain amount of current flow through it. A fuse for one line in your home's electrical system melts if more then 30A of current flow goes through it. Determine if the fuse will blow if the following appliances are all connected in Parallel to that line: a 13 ohms toaster, a 18 ohm dishwasher, a 24 ohm fridge, and a 15 ohm heater. The potential difference across all devices is 120V. Sketch this with a drawing and explain