Two hemispherical shells of inner diameter 1 m are joined together with 12 equally spaced bolts. If the interior pressure is raised to 300 kPa above atmospheric pressure, determine the tensile force in each bolt.

Two hemispherical shells of inner diameter 1 m are joined together with 12 equally spaced bolts. If the interior pressure is raised to 300 kPa above atmospheric pressure, determine the tensile force in each bolt.

Name: Two hemispherical shells of inner diameter 1 m are joined together wit
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: Two hemispherical shells of inner diameter 1 m are joined together with 12 equally spaced bolts. If the interior pressure is raised to 300 kPa above atmospheric pressure, determine the tensile force in each bolt.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.122P: The 12-ft wide quarter-circular gate AB is hinged at A. Determine the contact force between the gate...

See similar textbooks

Similar questions

The 12-ft wide quarter-circular gate AB is hinged at A. Determine the contact force between the gate and the smooth surface at B due to water pressure acting on the gate. Use =62.4lb/ft3 for water.
One side of the container has a 03-m square door that is hinged at its top edge. If the container is filled with water, determine the smallest force F that must be applied to the bottom edge of the door to keep it closed.
The cylindrical water tank with R = 10 ft and H = 1.6 ft has thin steel walls of uniform thickness and weighs 18000 lb when empty. Determine the depth of the water h for which the center of gravity G of the tank plus water will be located at the surface of the water. For water, use =62.4lb/ft3.
Determine the resultant force acting on the elbow of the thin-walled pipe when the pipe carries a uniform internal pressure p0.
Two hemispherical shells of inner diameter 1m are joined together with 12 equally spaced bolts. If the interior pressure is raised to 300kPa above atmospheric pressure, determine the tensile force in each bolt.
A vertical hydraulic cylinder has a piston with a diameter of 115 mm.If the ambient pressure is 100 kPa,determine the mass of the piston if the pressure inside is 950 kPa.
Determine the total pressure and depth of centre of pressure on a plane rectangular surface of 1 m wide and 3 m deep when its upper edge is horizontal and (a) coincides with water surface (b) 2 m below the free water surface.
The trough is filled to its top with carbon tetrachloride. Determine the magnitude of the resultant force acting on the semi-circular end plate, and the location of the center of pressure from the top.
Plate AB has a width of 1.5 m and a radius of 3 m. Determine the horizontal and vertical components of reaction at the pin A and the vertical reaction at the smooth stop B due to the water pressure. Strictly using General Solution, and please show pressure diagram.
The unpressurized cylindrical storage tank shown has a 3/16-in. wall thickness and is made of steel having a 60-ksi ultimate strength in ten-sion. Determine the maximum height h to which it can be filled with water if a factor of safety of 4.0 is desired. (Specific weight of water 562.4 lb/ft3.)
Show the derivation of the girth and longitudinalstresses of the thin-walled cylindrical container shownbelow. Say p is the internal pressure, d is the insidediameter of the container, and t is wall thickness. Seefigure 103.
The blade of the bulldozer shown below is rigidly attached to a linkage consisting of the arm AB, which is controlled by the hydraulic cylinder BC. There is an identical linkage on the other side of the bulldozer. Applied loads shown are for both linkages and F = 581 kN. Determine the pressure in hydraulic cylinder BC in Pa if the cylinder has a diameter of 80 mm.