. A voltage of 120V generates an IR drop across two resistors connected in series. If the voltage drop across R1 is 30V, what is the voltage drop across R2, in Volts? a) 80 b) 40 c) 100 d) 90 2. Three resistors R1, R2 and R3 of 20, 40 and 60 ohms are connected in parallel through the 120 V power line. What is the total current in the power line? a) 10A b) 12A c) 11A d) 15A 3. Resistors in a circuit are generally used to: a) increase the flow of the current b) decrease the flow of current c) avoid overvoltage d) decrease the power in the circ

. A voltage of 120V generates an IR drop across two resistors connected in series. If the voltage drop across R1 is 30V, what is the voltage drop across R2, in Volts? a) 80 b) 40 c) 100 d) 90 2. Three resistors R1, R2 and R3 of 20, 40 and 60 ohms are connected in parallel through the 120 V power line. What is the total current in the power line? a) 10A b) 12A c) 11A d) 15A 3. Resistors in a circuit are generally used to: a) increase the flow of the current b) decrease the flow of current c) avoid overvoltage d) decrease the power in the circ

College Physics

1st Edition

ISBN:9781938168000

Author:Paul Peter Urone, Roger Hinrichs

Publisher:Paul Peter Urone, Roger Hinrichs

Chapter21: Circuits And Dc Instruments

Section: Chapter Questions

Problem 53PE: A 1,00-?O voltmeter is placed in parallel with a 75.0kresistor in a circuit, (a) Draw a circuit...

See similar textbooks

Similar questions

A resistor is dissipating 119milliwatts [mW] of power. The voltage across the resistor is 26 volts [V]. (a) What is the value of the resistance? Express your answer in units of ohms[Ω]using an appropriate SI prefix such that there are only one, two, or three digits shown to the left of the decimal. (b) What is the current through the resistor? Express your answer in units of amperes [A] using an appropriate SI prefix such that there are only one, two, or three digits shown to the left of the decimal.
A resistor is dissipating 114 milliwatts [mW] of power. The voltage across the resistor is 13 volts [V]. (a) What is the value of the resistance? Express your answer in units of ohms [Ω] using an appropriate SI prefix such that there are only one, two, or three digits shown to the left of the decimal. (b) What is the current through the resistor? Express your answer in units of amperes [A] using an appropriate SI prefix such that there are only one, two, or three digits shown to the left of the decimal.
A constant current transfers 10*10^14 electrons onto one plate of a capacitor in 3 minutes [min]. (a) What is the current, in units of amperes [A]? Express the answer using an appropriate SI prefix such that there are only 1, 2, or 3 digits shown to the left of the decimal. (b) If the capacitor has a capacitance of microfarads [F], what is the voltage in units of volts [V] across the capacitor?
In the circuit shown in figure 1, all the resistors are rated a maximum power of 1.00 W. What is the maximum emf epsilon that the battery can have without burning up any of the resistors?
An electric device draws 6.10 AA at 240 VV. If the voltage drops by 25 %, what will be current, assuming nothing else changes? Express your answer to two significant figures and include the appropriate units. I final= If the resistance of the device were reduced by 25 %, what current would be drawn at 240 VV? Express your answer to two significant figures and include the appropriate units. I final=
What is the voltage change if you cross a resistor R in the same direction as the current I? (This means you want Vf-Vi, where Vi is the voltage where the current enters the resistor and Vf, is the voltage where the current leaves the resistor.) What is the voltage change if you cross a resistor R opposite the direction of the current I? (in this case, Vi is the voltage where the current leaves the resistor, and Vf is the voltage where the current enters the resistor.) Which answer is correct? +IR in both cases +IR in the first case and -IR in the second case. +IR in both cases -IR in the first case and +IR in the second case.
1. 9. In the circuit shown in the figure above, a power supplier of 50 V is connectedacross a resistance network. If R1 = 20 Ω, R2 = 10 Ω, R3 = 10 Ω, and R4 = 40 Ω. Whatis the equivalent resistor of the circuit? 2. 10. What is the current flowing through the R4 resistor in the circuit shown in Problem 9? 3. 11. What is the voltage across the R1 resistor in the circuit shown in Problem 9? 3.
In the left figure, create two formulations/equations of the currents IT, I1, I2, & I3 using the conceptof KCL. On the other hand, create two formulations/equations of the given voltages using theconcept of KVL on the right figure.
What voltage will produce 0.2 AA of current through a 4800-ΩΩ resistor? Express your answer to two significant figures and include the appropriate units. V=
In the circuit shown in figure 1, epsilon is equal to 41.0 V, R1= 4 ohms, R2= 6 ohms, and R3= 3 ohms. (A) what is the potential difference Vab between points a and b when the switch S is open? (B) for the 4 ohm resistor, calculate the current through the resistor with S open. (C) for the 6 ohm resistor, calculate the current through the resistor with S open. (D) for the 3 ohm resistor calculate the current through the resistor with S open. (E) what is the potential difference Vab between points a and b when the switch S is closed? (F) for the 4 ohm resistor calculate the current through the resistor with S closed. (G) for the 6 ohm resistor calculate the current through the resistor with S closed (H) for the 3 ohm resistor calculate the current through the resistor with S closed. (I) for each resistor, does the current increase or decrease when S is closed?
5 part A: If u(C) = 0.2C. What in the uncertainty of a 500 mF capacitor in mF? 5 Part B: If C = 500 mF and R = 8000 W , and V = 5 V. What is the voltage across the resistor in an RC circuit if it started out fully charged and the time since we started charging 6 seconds ago?
A current of I = 3.7 A passes through the circuit shown, where R = 78 Ω. (a) In terms of R, I, and numeric values, write an expression for the voltage of the source, V. (b) What is the voltage, V in volts?