. centrifugal pump rotates at 750 rpm. Water (p=1000) inters the impeller normal to blades (á = 0°) and exits at an angle (à = 35°) from radial. The inlet radius is 14 cm at which the blade width 18 cm. the outlet radius is 26 cm at which blade width 16.2 cm. The suction velocity 1.6 m/s and pump suction diameter 0.54m. Assuming the 85-percentage efficiency, Calculate the net head produced by this pump and calculate the required brake

. centrifugal pump rotates at 750 rpm. Water (p=1000) inters the impeller normal to blades (á = 0°) and exits at an angle (à = 35°) from radial. The inlet radius is 14 cm at which the blade width 18 cm. the outlet radius is 26 cm at which blade width 16.2 cm. The suction velocity 1.6 m/s and pump suction diameter 0.54m. Assuming the 85-percentage efficiency, Calculate the net head produced by this pump and calculate the required brake

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. A centrifugal pump with 30 cm impeller delivers 30 l/s against a head of 24 m when running at 1750 rpm. What will be the delivery of a homologous pump of 15 cm impeller diam eter assuming same efficiencies and speed? 2. A centrifugal pump with 2.3 diameter impeller running at 327 rpm delivers 7.9 m3/s of water. The head developed is 72.8 m. The width of the impeller at outlet is 0.22 m. If the overall efficiency is 91.7% determine the power to drive the pump.
A Francis turbine develops 3 MW under a head of 50 m at an overall efficiency of 88%. The diameterof the runner at the inlet is 80 cm and runner rotates with 300 rpm. If hydraulic efficiency of the turbine is90% and runner height at the inlet is 10cm, calculate (a) guide vane angle at inlet (b) blade angle at inletand (c) degree of reaction of the turbine.
While rotating at 900 rpm, a centrifugal pump delivers 2500 gpm of water at ahead of 75 ft. If the impeller diameter is 1.5 ft. and the blade width is 1.75 in.,find the (a) blade angle β2, (b) radial velocity Vr2, and (c) blade speed u2. Assumeno whirl at the inlet.Ans: β2=12.5°; Vr2=8.1 ft./s; u2=70.7 ft./s
A four-stage centrifugal pump has four identical impellers, keyed to the same shaft. The shaft is running at 400 r.p.m. and the total manometric head developed by the multistage pump is 40m. The discharge through the pump is 0.2 m*3/s. The vanes of each impeller are having outlet angle as 45°. If the width and diameter of each impeller at outlet is 5cm and 60 cm respectively, Find the manometric efficiency.
The impeller of a centrifugal pump has inner and outer diameters of 15 and 35 cm, respectively, and a flow rate of 0.15 m3/s at a rotational speed of 1400 rpm. The blade width of the impeller is 8 cm at the inlet and 3.5 cm at the outlet. If water enters the impeller in the radial direction and exits at an angle of 60° from the radial direction, determine the minimum power requirement for the pump
A four-stage centrifugal pump has four identical impellers, keyed to the same shaft. The shaftis running at 400 r.p.m. and the total manometric head developed by the multistage pump is 40m. The discharge through the pump is 0.2 m*3/s. The vanes of each impeller are having outlet angle as 45°. If the width and diameter of each impeller at outlet is 5cm and 60 cm respectively, Find the manometric efficiency.
A Francis radial-flow hydroturbine has the following dimensions, where location 2 is the inlet and location 1 is the outlet: r2 = 6.60 ft, r1 = 4.40 ft, b2 = 2.60 ft, and b1 = 7.20 ft. The runner blade angles are ?2 = 82° and ?1 = 46° at the turbine inlet and outlet, respectively. The runner rotates at n. = 120 rpm. The volume flow rate at design conditions is 4.70 ×106 gpm. Irreversible losses are neglected in this preliminary analysis. Calculate the angle ?2 through which the wicket gates should turn the flow, where ?2 is measured from the radial direction at the runner inlet. Calculate the swirl angle ?1, where ?1 is measured from the radial direction at the runner outlet. Does this turbine have forward or reverse swirl? Predict the power output (hp) and required net head (ft).
The length and diameter of a suction pipe of a single-acting reciprocating pump are 5m and 10 cm respectively. The pump has a plunger of diameter 15cm and a stroke length of 35 cm. The center of the pump is 3 m above the water surface in the pump. The atmospheric pressure head is 10.3 m of water and pump is running at 3r rpm. Determine: a. Pressure head due to acceleration at the beginning of the suction stroke, b. maximum pressure head due to acceleration and c. pressure head in the cylinder at the beginning and at the end of the stroke
A centrifugal pump impeller has a diameter of 15 cm at the inlet and a blade width of 6.3 cm. The radius at the exit is 35 cm and the wing width is 3.2 cm. Centrifugal pump rotates at 1500 rpm. The water enters the fins in a normal (perpendicular) manner and leaves 38 ° deviating from the radial direction. Volumetric flow rate is given as 0.25 m ^ 3 / s. Find the required shaft power for the centrifugal pump, assuming the efficiency as 100%. (P = water = 998 kg / m ^ 3)
A centrifugal pump rotates at n. = 750 rpm. Water enters the impeller normal to the blades (?1 = 0°) and exits at an angle of 35° from radial (?2 = 35°). The inlet radius is r1 = 12.0 cm, at which the blade width b1 = 18.0 cm. The outlet radius is r2 = 24.0 cm, at which the blade width b2 = 16.2 cm. The volume flow rate is 0.573 m3 /s. Assuming 100 percent efficiency, calculate the net head produced by this pump in cm of water column height. Also calculate the required brake horsepower in W
A backward-swept centrifugal fan develops a pressure of 80 mm of water gauge. It has an impeller diameter of 0.89 m and runs at 720 rpm. The blade angle at the tip is 39° and the width of the impeller is 0.1m. Assuming a constant radial velocity of 9.15 m/s and density of air as 1.2 kg/ m3 , determine the fan efficiency, discharge and power required.
Before solve the problem please understand the question. Give me right solution according to the question. A flow rate of 0.14 m3 / s is required from a centrifugal pump with an outer radius of 23cm and rotating at 900 rpm. The width of the propeller is b = 8cm (at the outlet). Assuming 73% efficiency, what motor horsepower is required if the outlet angle is 165º? Suppose the pallets occupy 5% of the exit area.