. Create a good label (name) for each signal described below: (a)*A sensor outputs a LOW when the elevator door is closed (b) A streetlight sensor outputs a HIGH when it detects daylight (c)*A passenger seat sensor goes LOW when the seat is empty (d) A temperature sensor goes HIGH when the radiator fluid is criti- cally hot

. Create a good label (name) for each signal described below: (a)A sensor outputs a LOW when the elevator door is closed (b) A streetlight sensor outputs a HIGH when it detects daylight (c)A passenger seat sensor goes LOW when the seat is empty (d) A temperature sensor goes HIGH when the radiator fluid is criti- cally hot

College Physics

1st Edition

ISBN:9781938168000

Author:Paul Peter Urone, Roger Hinrichs

Publisher:Paul Peter Urone, Roger Hinrichs

Chapter7: Work, Energy, And Energy Resources

Section: Chapter Questions

Problem 31PE: Suppose a star 1000 times brighter than our Sun (that is, emitting 1000 times the power) suddenly...

See similar textbooks

Similar questions

A stenosis produces a high-speed jet in a vessel. The maximum velocity of RBCs in the stenosis is 80 cm/sec. Find the minimum PRF that must be used to avoid aliasing for pulsed Doppler at 7.5 MHz. Assume that the angle of sonation is 0 degrees.
Two parallel disks of diameter D = 3 ft separatedby L = 2 ft are located directly on top of each other. Thedisks are separated by a radiation shield whose emissivity is0.15. Both disks are black and are maintained at temperaturesof 1200 R and 700 R, respectively. The environment that thedisks are in can be considered to be a blackbody at 540 R.Determine the net rate of radiation heat transfer through theshield under steady conditions.
A quality assurance engineer at a frying pan company is asked to qualify a new line of nonstick-coated frying pans. The coating needs to be 1.00 mm thick. One method to test the thickness is for the engineer to pick a percentage of the pans manufactured, strip off the coating, and measure the thickness using a micrometer. This method is a destructive testing method. Instead, the engineer decides that every frying pan will be tested using a nondestructive method. An ultrasonic transducer is used that produces sound waves with a frequency of f=25 kHz. The sound waves are sent through the coating and are reflected by the interface between the coating and the metal pan, and the time is recorded. The wavelength of the ultrasonic waves in the coating is 0.076 m. What should be the time recorded if the coating is the correct thickness (1.00 mm)?
Suppose a star 1000 times brighter than our Sun (that is, emitting 1000 times the power) suddenly goes supernova. Using data from Table 7.3: (a) By what factor does its power output increase? (b) How many times brighter than our entire Milky Way galaxy is the supernova? (c) Based on your answers, discuss whether it should be possible to observe supernovas in distant galaxies. Note that there are on the order of 1011 observable galaxies, the average brightness of which is somewhat less than our own galaxy.
The coorect answer should have variable m in it
In the acoustic interferometer in the figure, the speaker emits a sound of frequency 10 kHz and the distance L has been set such that the microphone picks up a maximum intensity. The upper arm (shaded section) is then immersed in liquid nitrogen, so that the temperature of the air in this region of the tube slowly drops from the ambient temperature of 27 ⁰C to -100 ⁰C. Given that the speed of sound in air at a temperature T (in Kelvin) is vsom = √(gamma*R*T/Mmolar) and treating air as a diatomic ideal gas (gamma = 7/5) of molar mass Mmolar = 28.88 g, calculate how many times the microphone will pick up minima of intensity during the process. Assume R = 8.314 J/K.mol and consider that the air temperature does not change in the other sections of the interferometer.
UPVOTE WILL BE GIVEN! PLEASE WRITE THE SOLUTIONS COMPLETELY AND LEGIBLY. PLEASE ANSWER #2 1. Calculate the sabins of absorption at 1000 Hz in a room that has dimensions of 11.00m wide x 15.00m long x 3.50m high. The room has: a. Plasterboard (12mm(1/2") in suspended ceiling grid b. Walls are constructed of concrete blocks (coarse). c. The floor is covered with marble. 2. The absorption coefficients of the materials at 1000Hz are as follows: a. Plasterboard (12mm(1/2") in suspended ceiling grid – 0.04 b. Concrete blocks (coarse) - 0.29 c. Marble flooring -0.01 3. Compute the reverberation time (RT60) of the room. 4. Is the reverberation time appropriate for a room designed for speech? 5. As a designer, what will you recommend 5 to increase (or decrease) the reverberation time?
Assume the radiation from a heat lamp is monochromatic, with a wavelength of 1.5 μm . If the lamp’s 182.75-W output is focused on a person’s shoulder, over a circular area 26.5 cm in diameter, what is the intensity in kilowatts per square meter?
For the following process steps.. assume that you use a positive photoresist and that etch selectivity is infinite. A composite plot of four photo masks is given in Fig. 3- 26. Assume that mask alignment is perfect. All contact sizes are 0.5 x 0.5 µm. The poly 1 and poly 2 areas are opaque. and the contact I and contact 2 areas are clear in the masks. Draw the cross section at the end of each process step along the cut line shown in the figure
At 2200 degrees Celsius, the max wavelength for the Cs lamp is at 1252 nm. The measured spectral radiance is 1.86 x 10^10 J/m^3s. If the lamp is enclosed in a quartz envelope with a transmission factor of 0.92, find the spectral emissivity for the Cs lamp.
What letter corresponds to a peak maximum?
The heat capacity of liquid 4He below 0.6 K is proportional to T3, with the measured value Cv/Nk = (T/4.67 K)3. This behavior suggests that the dominant excitations at low temperature are long-wavelength phonons. The only important difference between phonons in a liquid and phonons in a solid is that a liquid cannot transmit transversely polarized waves-sound waves must be longitudinaL The speed of sound in liquid 4He is 238 mis, and the density is 0.145 g/cm3 . From these numbers, calculate the phonon contribution to the heat capacity of 4He in the low-temperature limit, and compare to the measured value.