The surface tension of water in contact with air at 20°C is0.0725N/m. The pressure inside a droplet of water is to be0.02N/cm² greater than the outside pressure. Calculatethe diameter of the droplet of water.

Given:- temperature=20 degree celcius surface tension=0.0725N/m Pressure=0.02N/cm2 To find:-…

Answered: .0725N/m. The pressure inside a droplet…

Engineering

Civil Engineering

.0725N/m. The pressure inside a droplet of wa .02N/cm2 greater than the outside pressure. C 2015м 30 оор 54+39 охоор

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter10: Force And Force-related Variables In Engineering

Section: Chapter Questions

Problem 18P: Using the information given in Table 10.4, determine the ratio of local pressure and density to...

See similar textbooks

Related questions

Q: A -5m 120 KN B L = 15 m constant El E = 30 GPa 120 kN ↓ C -3 m

Q: 3-10. The block has a weight of 20 lb and is being hoisted for equilibrium at uniform velocity.…

A: Given: Weight of block= 20lb Find Angle theta and force in cord AB

Q: x -3 ft D G -500 lb 200 lb E B F C 6 ft 6 ft 2 ft 4 ft y

Q: 3.2 Using the average-end-area method, calculate the cut-and-fill volumes 101 stations 15+00 through…

Q: Study the water tank illustrated in Figure 1 below and calculate the horizontal distance (x) the…

A: To find out the horizontal distance of free jet of water travel before striking the ground.

Q: (3b) State and explain the four types of geological formations of groundwater

A: Geological formation of groundwater is of 4 types: Aquifer Aquifuge Aquitard Aquiclude

Q: Calculate the forces in members BC, BE, and EF. Solve for each force from an equilibrium equation…

A: Since, it is a cantilever truss and in this case we do not need to find the support reactions.Sign…

Q: 1. A rectangular beam with b = 250 mm and d = 460 mm is reinforced for tension only with 3-25 mm…

Q: Determine the maximum stress of the plate.

A: Given data, Diameter of the hole,d= 2 cm=20 mm width,b= 7 cm= 70 mm Uni-axial tension=54 MPa…

Q: 4 in 7/8 in 7/8 in 2. The lap joint shown in the figure, is fastened by four 25mm.-diameter rivets.…

A: 1in=25.4cm d=25mm t= 7/8 in T find safe load P

Q: 4. A rectangular beam with b = 250 mm and d = 460 mm is reinforced for tension only with 3-25 mm…

A: Given : b = 250 mm, d = 460 mm fy = 276.5 MPa fc' = 20.7 MPa Required: Ultimate moment…

Q: c) Classify the following into the various types of vertical curves. i. G1 = +2%, G2 = +3% ii. G1 =…

A: Note:- Hi! Thank you for the question, As per the honor code, we are allowed to answer three…

Q: carries a uniform dead load of 0. 680 KN/m including its own weight. Use fy=276.50 MPa and fc'=20.70…

A: b=250mm d=460mm 3-25mm bars L=6m fy=276.50Mpa f'c=20.70Mpa

Q: Draw the moment diagrams for the frame. Assume the frame is pin connected at A, B, and C and fixed…

A: Given data:-

Q: 1. The gate below will automatically open if the water level drops below a certain elevation.…

Q: b) Solve for the forces in each of the members. (the reaction forces are shown) 4,000 N

A: Given :

Q: Classify the soil A & B using USCS system

A: ##Classification of SOIL A AND B using USCS system ###

Q: Draw the shear and moment diagram of the continuous beam.

A: L = 3+3+3+4 = 13m

Q: Car A is traveling at a location where the speed limit is 100 km/h. The police officer in car P…

A: To solve this problem, first we need to change the value of speed in m/sec. Then using the equation…

Q: A cantilever beam having rectangular cross section with varying width band varying height h, is…

A: To find out the value of hx tofully stress of the beam.

Q: A cantilever beam of negligible mass has a mass m at its free end. If the length of the cantilever…

Q: Answer D and

Q: The equation of the three hinged symmetrical arch for the given coordinate is, when the arch perform…

Q: 10, KN A 1m 10 kN/m 1m 5 kN/m 3m Find the resultant Find the location of the resultant from pt. A…

A: Objective: To determine resultant of the forces system, location of the resultant from points A and…

Q: 2. A hydraulic press contains 1.0 m³. The areas of the small and large piston are 1.60 cm² and 645…

Q: Consider a soil with the following properties: n = 0.4, Ks = 1.93 m/d, 0 = 0.09, = 0.8 m, λ = 0.26.…

A: To solve this problem, firstly the value of unsaturated conductivity will be calculated. Since there…

Q: Calculate the force in members GD, GE, GF, and FD of the space truss. Identify if the members are in…

Q: Figure (a) shows the cross section of square footing of 3 m x 3 m. The soil properties are shown in…

A: Given, B = 3m γd = 18.5 kN/m3 ϕ = 30o

Q: Problem- For two infinite slopes (one in dry condition and other in submerged condition) in a sand…

Q: 8 mm- 8 mm 250 mm 8 mm steel beam has the cross-sectional area shown. The beam is loaded as shown…

A: Given : w = 70 kN/m Determine the absolute max. bending stress ?

Q: Q10. Determine the percentages of gravel, sand, silt and clay for each soil shown in Figure Q10 in…

A: To Determine :- The percentages of gravel, sand, silt and clay for each soil in accordance with the…

Q: Consider the beam and loading shown in the figure below. The beam has a flexural rigidity of El over…

Q: A circular metallic rod of length 250 mm is placed between two rigid immovable walls as shown in the…

A: To determine the axial stress developed in rod. Given data, L= 250 mm E = 200 GPa ΔT = 200 °C Gap…

Q: Draw the moment diagrams for the frame. Assume the frame is pin connected at A, B, and C. 6 kN/m A…

Q: Problem 2 Determine the forces in the members AB, AC, and AD of the space truss shown in figure…

A: Given : Determine forces in member AB, AC and AD?

Q: A rectangular open channel has a width of 5m and a bed slope of 0.001. For a uniform flow of depth…

A: Given data, Depth (y) = 2 m Width (B) = 5 m Bed Slope = 0.001 Velocity = 2 m/s To find out the…

Q: Er is constant. 40 kN/m 80 KN 2 m 50 kN

Q: CE 2131 PRACTICE PROBLEM ON CLOSED TRAVERSE. Determine the adjusted bearings of the following…

Q: During the subsurface investigations for design of foundations, a standard penetration test was…

A: Given- Water table at ground, Soil is fine sand, Correction factor for overburden=1.0, Rest is given…

Q: TABLE 1 LINE 1-2 2-3 3-4 4-5 5-1 TABLE 2 LINE 1-2 2-3 3-4 4-5 5-1 FORWARD BEARING S 38° 39' W N…

Q: 3. A rectangular beam with b = 250 mm and d = 460 mm is reinforced for tension only with 3-25 mm…

A: Answer We are given Width of beam b = 250 mm Effective depth of beam d = 460 mm Area of steel As…

Q: The graph shows the displacement-time history for the rectilinear motion of a particle during an…

Q: at uniform velocity. Determine the angle for equilibr and the force in cord AB. B 20° A D

Q: In order to determine the elevation of top Q of a signal on a hill, observations were made from two…

Q: A 30-m band standardized at 20°C was found to be 30.003 m. At what temperature is the tapeexactly30…

Q: The culturable commanded area for a distributary is 2 x 108 m². The intensity of irrigation for a…

Q: The beam shown in Fig1.carries a concentrated load of W and a total distributed load of 8 W.…

A: Given data:- Concentrated load = W Total distributed load = 8 W Allowable stresses in tension = 60…

Q: oblem- A sphere resting in a smooth V-shaped groove and subjected to a spring force. The spring is…

Q: The following question refers to the ACI Code. A 16" x 18" concrete Column requires 8 - #11 Vertical…

A: Given:- The dimensions of the concrete column = 16" × 18" The steel reinforcement provided = 8 - #11…

Q: . Determine the component. Determine first if the frame is statically determinate using degree of…

A: Given: Required: Determine determinacy and find support reactions

Concept explainers

Pressure and Stress

Question

The surface tension of water in contact with air at 20°C is
0.0725N/m. The pressure inside a droplet of water is to be
0.02N/cm² greater than the outside pressure. Calculate
the diameter of the droplet of water.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1 Solution:-

VIEW

Step 2 Solution:-

VIEW

Step 3 Answer:-

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

An astronaut has a mass of 68 kg. What is the weight of the astronaut on Earth at sea level? What are the mass and the weight of the astronaut on the Moon, and on Mars? What is the ratio of the pressure exerted by the astronauts shoe on Earth to Mars?
Using the information given in Table 10.4, determine the ratio of local pressure and density to sea-level values. Estimate the value of air density at the cruising altitude of most commercial airliners. Altitude (m) sealevel PPsealevel 0 (sea level) 1000 3000 5000 8000 10,000 12,000 14,000 15,000
Lake Mead, near the Hoover Dam, which is the largest man-made lake in the United States, contains 28,537,000 acre-foot of water (an acre-foot is the amount of water required to cover 1 acre to a depth of 1 foot). Express the mass of the water volume in kg and lbm.
A jet plane taking off creates a noise with a magnitude of approximately 125 dB. What is the magnitude of the pressure disturbance (in Pa)?
Calculate the capillary effect in millimeters in a glass tube of 4mm diameter, when immersed in Water Mercury the temperature of the liquid is 200C in contact with air are 0.073575 N/m and 0.51 N/m respectively. The angle of contact for water is zero and that for mercury is 1300. Take density of water at 200C as equal to 998 kg/m3. Explain the ways of describing the fluid motion
Given a liquid water having a volume of 6m3 and weight of 44kN at 4°C, Calculate a. Specific weight (N/m3) b. Specific mass (kg/m3) c. Specific volume (m3/kg) d. Specific gravity (unitless)
Calculate the pressure decrease (in psi) when you climb from an elevation of 660 ft to a mountain top 1640 ft above mean sea level. Assume that the unit weight of air is constant at 0.07967 lb/ft^3.
Air is introduced through a nozzle into a tank of water to form a stream of bubbles. If the bubbles are intended to have a diameter of 2mm, calculate by how much the pressure of the air at the nozzle must exceed that of the surrounding water. Assume that surface tension of water is 0.073 N/m. What would be the absolute pressure inside the bubble if the surrounding water is at 100 kPa?
Q7. If the surface tension at air - water interface is 0.069 N / m, what is the pressure difference between inside and outside of an air bubble of diameter 0.009 mm?
For water, starting with 1 m3 of water in a container, what is the pressure required to decrease the volume of water by 1%?
Assuming specific weight of air to be constant, what is the approximate height of Mount Banahaw in m if a mercury barometer at the base of the mountain reads 654 mm and at the same instant, another barometer at the top of the mountain reads 480 mm? Show Unit Analysis Solution
What is the pressure of the air in the tank if z = 40 cm, y =100 cm, and x = 80 cm?